User Manual for Kinan models including: KVM-1508XX 8 Port 19 LCD KVM Console, KVM-1508XX, 8 Port 19 LCD KVM Console, LCD KVM Console, KVM Console, Console
8-Port Cat5 1U Rack Mount KVM Console, 19" Rackmount Monitor and Keyboard, 8 VGA to RJ45 Dongles Included, 23.8" Deep, OSD/Hotkey/Button Switching,1280×1024@60Hz, Support Windows, Linux, Mac and Sun : Electronics
File Info : application/pdf, 8 Pages, 439.35KB
DocumentDocument19LCD KVM Console (8 Port/ 16 Port) User Manual Print date: 2023 / 04 Version: V1.2 8 Port /16 Port User Manual The CAT5 LCD KVM console integrates multiple-port CAT5 KVM switches in a 1U height console. Multiple computers can be controlled from the single monitor-keyboard-mouse console. KVM Installation Diagram 1) Make sure the KVM console has been connected to the ground. ( ) 2) Connect the adapter to the KVM and the PC or server() 3) Connect any available KVM port and KVM adapter with CAT5 cables. ( ) 4) Plug the female port of the power cable in the KVM power socket, and plug the male port in the AC power port. ( ) Note: 1. Connect external USB keyboard, mouse and monitor according to the()step in 2. If cascading required, please connect KVM console and KVM switch with adapter (), and Hotkey need to be different with KVM console and KVM switch. Please check the hotkey setting 2.1 Turn off Mouse Hotkey function (F4: Tool ->Mouse HotOn) 2.1 Keyboard hotkey setting (F3: Set -> OSD Hotkey) Caps Lock +Caps Lock F12 +F12 Ctrl+Ctrl+KVM Hotkey -2- 8 Port /16 Port Opening the Console 1. Release the release catch; User Manual UNLOCK UNLOCK UNLOCK Note: The release lock can only do horizontal locking, it doesn't bear any load. 2. Pull the KVM console all the way out until it clicks into place; 3. Rotate the LED module all the way back to expose the LED screen; the LED module can be rotated up to 108°. Best Resolution : 1280x1024@60Hz 4. The KVM makes two "beep" sounds after power on, an OSD window appears for you to input user name and password. The orange LED and LED tube are flashing before you enter your password. 5. LED panel is powered on when the power LED is green. 6. Power on the computer or server after power on the KVM. The factory default pass word is blank; double click "Enter "to log in. -3- 8 Port /16 Port User Manual Closing the console Close the LED display panel and the power automatically shut down. Push the release catch in the direction of the arrow, push the LED panel all the way in until it automatically lock up. Key AUTO LOCK Operating the Monitor Figure 3.4 Monitor adjust menu buttons The LED OSD allows you to set up and configure the LED display. Buttons Functions MENU SELECT Brings up the main menu. EXIT/AUTO Exits the current menu and returns to the previous menu or exits the LED OSD. Press AUTO for automatic configuration. SL-/SL+ Moves the menu to make corresponding adjustment. LED state Green: Running Red: Power off or access nonstandard VESA signal Flashing green: Energy saving mode or no signal Press AUTO if the screen migrates after power on or under other circumstances, then the screen auto-configures to its best display state. Note: It may not be adjusted to its best state if part of the display mode is not standard VESA mode. If so, return back to OSD menu to RESET, then it will revert back to normal. It is recommended to set up the display mode at 1280×1024@60Hz, refresh rate at 60Hz. -4- 8 Port /16 Port LED Functions User Manual No. Components 1-16 Reset Scan 1 Brightness Definition Initialize 2 Port Selection Buttons & LEDs 3 Station ID Function Switching freely from port 1 to port 16 Press 1 and2 at the same time for three seconds resets the keyboard and mouse Press 7 and 8at the same time for three seconds enters the auto scan mode. Press 3 for three seconds enters brightness adjusting mode. 33 are flashing on the LED tube. Then press 56to adjust. Press3exits or waits for five seconds and it will auto-exit. Press 4 for three seconds enters definition adjusting mode. 44 are flashing on the LED tube. Then press 56to adjust. Press 4 exits or waits for five seconds and it will auto-exit Press 6 for three seconds will initialize the brightness and definition of each port. Indicator LEDs are built into the switches, the online LED light is on the left and the selected LED light is on the right. 1) An online LED light (green) indicates that the KVM has connected to its corresponding computer and power on. 2) A selected LED light (orange) indicates that the computer attached to its corresponding port is up and running. Display the current port -5- 8 Port /16 Port User Manual OSD Operation Double click the right button of the mouse or double click hotkeyScroll Lock to invoke below OSD main menu. You can customize the OSD hotkeys; find more details in OSD function instructions. To access the OSD menu through keyboard: 1.In the submenus that appears, moving the highlight bar to your selected port and then press Enter. 2. Press any key from 0-9to enter any port of current station To access the OSD menu through mouse: move port selection single click port switch single clickport switch double clickappear OSD menu single clickexit OSD menu *Note: Operate via keyboard after invoke the OSD menu via the touchpad. -6- 8 Port /16 Port User Manual OSD Functions Menu Keys ADM F1 Scan F2 Set F3 Tool F4 Edit F6 QV F7 Lout F8 Esc Exit Scroll Lock Num Lock Submenu/Explanation Set User login-Set User login account and password Set accessible-Set access permissions BRC Mode -monitor multiple computers at the same time Load Default-reset the menu to the original factory default settings All-Lists all the ports on the installation Power On-lists only powered on ports that have attached computers. Quick View-Lists only the ports that have been selected as Quick View ports Auto Scan-set scanning time period Port ID-set how long a port displays on the monitor OSD Hotkey-set OSD hotkeys Lout Time off- to set the time out value Reset RGB-Press Enter reset RGB BeeperOn-press Enter switch Bee sounds Mouse HotOn-press Enter to close touchpad operating on OSD. Restore Values-press Enter restore the current user default value. About KVM- press Enter shows the KVM version Edits port names Start or close Quick View Log out/lock the KVM Press this key exits OSD menu Press this key exits OSD menu Press this key exits OSD menu The display screen will be distorted if the CAT5 cable is too long, for this case, you can adjust according to below steps: 1Press+and ADJ FOCUS will pop up, then press+,-to adjust definition. 2Press and ADJ BRIGHT will pop up, then press, . to adjust brightness. -7- 8 Port /16 Port User Manual Specifications (19") Model 8 Port 16 Port Computer Direct 8 16 connections Max 256 512 Port emulation Keyboard, mouse PS/2, USB LCD model SXGA TFT LCD monitor View area Optimum resolution Display color 19 1280×1024@60Hz 16.7 M Brightness 250cd/m² T y p Contrast ratio 1000 : 1 T y p Pixel pitch(mm) 0.2928(H) × 0.2928(W) Mouse Keyboard Port selection Input power X/Y resolution Touchpad with trackball >1000 points / inch, (40 points/mm) Eliminates the need for an external mouse 99 keys (82 keys main keyboard +17 independent small number pad) Front panel pushbuttons, hotkeys, OSD menu 100V- 240Vac , 50-60Hz , <1.5A Power consumption 20W 21W Operating temperature 0 -- 50 Store temperature -20 -- 60 Humidity 0--80% RH, non-condensing Net weight 13.4kg 13.4kg Product dimension (W × D × H) 448mm×605mm×42.5mm Package dimension (W × D × H) 765mm×615mm×185mm -8-