Installation Guide for tp-link models including: POE150S PoE Injector Splitter, POE150S, PoE Injector Splitter, Injector Splitter, Splitter
Pobierz POE10R | TP-Link Polska
POE10R
File Info : application/pdf, 2 Pages, 477.97KB
DocumentDocumentInstallation Guide
PoE Injector and PoE Splitter
To ask questions, find answers, and communicate with TP-Link users or engineers, please visit https://community.tp-link.com to join TP-Link Community. For technical support and other information, please visit https://www.tp-link.com/support, or simply scan the QR code.
© 2023 TP-Link 7106510639 REV6.20.0
Some models featured in this guide may be unavailable in your country or region. For local sales information, visit https://www.tp-link.com. For simplicity, we will take POE150S and POE10R for example throughout the Guide, other models may differ in appearance.
PoE Injector Only The PoE Injector supplies steady power and data connectivity to a powered device such as PoE IP Camera, PoE AP and PoE IP Phone through an Ethernet cable.
Power Socket
Ethernet Device (switch, router, etc.)
PoE Injector
Powered Device (PD)
LAN IN
PWR DC 48V
IP Camera
AP
IP Phone
Note: The maximum output power of POE150S is 15.4W. PoE devices that require more than 15.4W are not supported.
PoE Splitter Only The PoE Splitter can be used with a PoE/PoE+ switch to deliver direct current (DC) power and data to a Non-PoE device.
PoE/PoE+ Switch
PoE Splitter
LAN OUT
PWR DC OUT
12V 9V 5V
Note: Set the required voltage of the non-PoE device before cable connection.
Non-PoE Device (suggested power:<12 W)
PoEInjector PoE Spli ter PoEInjector
PoE Spli ter
PoE Injector & Splitter The PoE injector and PoE splitter can be used as a kit to supply power and transmit data to a Non-PoE device.
Power Socket
Ethernet Device (switch, router, etc.)
PoE Injector
LAN IN
PWR DC 48V
PoE Splitter
LAN OUT
PWR DC OUT
12V 9V 5V
Non-PoE Device (suggested power:<12 W)
Note: Set the required voltage of the non-PoE device before cable connection.
Power LED Explanation
PoE Injector:
PoE Splitter:
PoEInjector PoE Spli ter
LAN IN
PWR DC 48V
On: Supplying power normally Off: No power supply
LAN OUT
PWR DC OUT
On: Connected to PSE correctly Off: No PSE is connected
FAQ
Q1. Can the PoE injector supply power to a PoE device which doesn't have a gigabit PoE port?
A: Yes. All RJ45 ports of the PoE injector support 10/100/1000 Mbps auto-negotiation.
Q2. What can I do if my PoE injector doesn't supply power to the powered device or the supplied power is unstable?
A1: Ensure the PD is PoE-compliant and its connecting port supports the PoE function.
A2: Ensure the power consumption of the PD doesn't exceed 15.4 W, otherwise the overload protection of the PoE injector will be activated. The quality and length of the Ethernet cable may influence the reception of the power supply.
Q3. Must I use the PoE injector together with the PoE splitter?
A: No. The PoE injector can supply power to all PDs support PoE function. The PoE splitter is used with a PoE switch or the PoE injector to supply power to a non-PoE device.
Q4. The Power LED of PoE injector is not lit.
A1: Ensure the power cord is connected the PoE injector with power source properly.
A2: Ensure the power consumption of the PD doesn't exceed 15.4 W, otherwise the PoE injector will activate the overload protection and the power will be cut off.
Specifications
General Specifications
Standards IEEE 802.3i, IEEE802.3u, IEEE 802.3ab, IEEE 802.3af
LED Cable Type
PWR
UTP/STP of Cat. 5 or above (based on the standards that the connected devices comply with)
Ports
POE150S: 10/100/1000 Mbps Auto-Negotiation RJ45 LAN IN Port 10/100/1000 Mbps Auto-Negotiation RJ45 POWER+DATA OUT Port DC 48 V Power Input Port
POE10R: 10/100/1000 Mbps Auto-Negotiation RJ45 POWER+DATA IN Port 10/100/1000 Mbps Auto-Negotiation RJ45 LAN OUT Port 5V / 9V / 12V DC OUT Power Output Port
Environmental and Physical Specifications
Operating Temperature Storage Temperature Operating Humidity
0°C to 40°C (32°F to 104°F) -40°C to 70°C (-40°F to 158°F) 10% to 90% non-condensing
Storage Humidity
5% to 90% non-condensing
Safety Information
Keep the device away from water, fire, humidity or hot environments. Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us. Do not use any other chargers than those recommended. Do not use damaged charger or USB cable to charge the device. Adapter shall be installed near the equipment and shall be easily accessible.
Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.
FCC compliance information statement
Product Name: PoE Injector
Model Number: POE150S
Component Name
Model
I.T.E. POWER SUPPLY
T480038-2B1
Product Name: PoE Splitter
Model Number: POE10R Responsible party:
TP-Link USA Corporation
Address: 10 Mauchly, Irvine, CA 92618
Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6804
E-mail: sales.usa@tp-link.com
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.
Issue Date: 2024.01.24
FCC compliance information statement
Product Name: I.T.E. POWER SUPPLY Model Number: T480038-2B1 Responsible party: TP-Link USA Corporation Address: 10 Mauchly, Irvine, CA 92618 Website: https://www.tp-link.com/us/ Tel: +1 626 333 0234 Fax: +1 909 527 6804 E-mail: sales.usa@tp-link.com This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.
Issue Date: 2024.01.24
, .
Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)
CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
BSMI Notice (For POE150S)
Pb
Cd
Hg
Cr+6
PCB
-
-
1"" 2" - "
PBB
PBDE
EU Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863. The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce.
UK Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016. The original UK Declaration of Conformity may be found at https://www.tp-link.com/support/ukca
, .
Explanaon of the symbols on the product label
Symbols may vary from productsThe label is at the bottom of the product.
Symbol
Explanation
Cl a ss II equipment
Cl a ss II equipment with functional earthing Alternating current Direct current Pol a rity of d.c. power connector
For indoor use only
Dangerous voltage
Ca uti on, risk of electric shock
Energy efficiency Ma rking
Protecti ve earth
Ea rth
Fra me or chassis
Functional earthing
Ca uti on, hot surface
Ca uti on
Opera tor's manual
Stand-by
"ON"/"OFF" (push-push)
Fuse
Fuse is used in neutral N
RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
Ca uti on, avoid listening a t high vol ume l evels for l ong periods
Di s connection, a ll power plugs
m
Switch of mini-gap construction
Switch of micro- gap construction (for US version)
µ
Switch of micro-gap /micro-disconnection construction
(for other versions except US)
Switch without contact gap (Semiconductor switching device)
Link: The wallet designed for the internet
TP-Link Community
TP-Link: Your Smart Home, Simplified