User Manual for Optoma models including: ZU1300 DLP Laser Projector, ZU1300, DLP Laser Projector, Laser Projector, Projector
Optoma ZU1300 ZU1300
File Info : application/pdf, 104 Pages, 23.99MB
DocumentDocumentDLP® Projector User manual TABLE OF CONTENTS SAFETY............................................................................................... 5 Important safety instructions...................................................................................................... 5 Light Intensity Hazard Distance................................................................................................. 6 Laser radiation safety information ............................................................................................. 6 Product safety labels ................................................................................................................. 7 Light beam related safety labels........................................................................................... 7 Copyright ................................................................................................................................... 8 Disclaimer.................................................................................................................................. 8 Trademark recognition............................................................................................................... 8 FCC ........................................................................................................................................... 8 Declaration of conformity for EU countries ................................................................................ 9 WEEE ........................................................................................................................................ 9 INTRODUCTION ............................................................................... 10 Package overview .................................................................................................................... 10 Standard accessories ............................................................................................................... 10 Optional accessories ................................................................................................................ 11 Product overview ...................................................................................................................... 12 Connections.............................................................................................................................. 13 Keypad ..................................................................................................................................... 14 Remote control ......................................................................................................................... 15 SETUP AND INSTALLATION........................................................... 16 Installing the projection lens ..................................................................................................... 16 Adjusting the projector position ................................................................................................ 18 Boresight adjustment................................................................................................................ 20 Required tool ....................................................................................................................... 20 Setting the projector start mode .......................................................................................... 20 Performing the boresight adjustment .................................................................................. 20 BX-CTA17 Boresight Tool Operating................................................................................... 23 Connecting sources to the projector......................................................................................... 25 Adjusting the projector image ................................................................................................... 26 Remote setup ........................................................................................................................... 27 USING THE PROJECTOR ............................................................... 30 Powering on / off the projector.................................................................................................. 30 Selecting an input source ......................................................................................................... 31 Menu navigation and features .................................................................................................. 32 OSD menu tree......................................................................................................................... 33 Image menu.............................................................................................................................. 48 Picture Mode ....................................................................................................................... 48 Dynamic Range................................................................................................................... 49 2 English Brightness ........................................................................................................................... 49 Contrast............................................................................................................................... 49 Sharpness ........................................................................................................................... 49 Gamma................................................................................................................................ 49 Dynamic Contrast................................................................................................................ 50 Color Settings...................................................................................................................... 50 Wall Color ............................................................................................................................ 51 3D Setup ............................................................................................................................. 51 Save to User........................................................................................................................ 53 Apply to User....................................................................................................................... 53 Reset ................................................................................................................................... 53 Display menu............................................................................................................................ 54 Aspect Ratio ........................................................................................................................ 54 Digital Zoom ........................................................................................................................ 54 Geometric Correction .......................................................................................................... 55 Edge Mask .......................................................................................................................... 57 Freeze Screen..................................................................................................................... 57 Test Pattern ......................................................................................................................... 57 PIP/PBP............................................................................................................................... 58 Reset ................................................................................................................................... 59 Input Settings menu.................................................................................................................. 60 Auto Source......................................................................................................................... 60 Quick Resync ...................................................................................................................... 60 Active Inputs........................................................................................................................ 60 Latency Adjustment ............................................................................................................. 60 Backup Input ....................................................................................................................... 60 HDMI ................................................................................................................................... 61 Reset ................................................................................................................................... 61 Device Setup menu .................................................................................................................. 62 Language ............................................................................................................................ 62 Projection ............................................................................................................................ 62 Lens Settings....................................................................................................................... 62 Schedule ............................................................................................................................. 64 Date and Time..................................................................................................................... 66 Power Settings .................................................................................................................... 67 Light Source Settings .......................................................................................................... 67 Shutter................................................................................................................................. 68 Security ............................................................................................................................... 68 On Screen Display .............................................................................................................. 68 Logo Setup .......................................................................................................................... 69 Backlight.............................................................................................................................. 69 High Altitude ........................................................................................................................ 69 User Data ............................................................................................................................ 69 System Update (FOTA) ....................................................................................................... 69 Reset ................................................................................................................................... 69 Communication menu............................................................................................................... 70 Projector ID ......................................................................................................................... 70 Remote Setup ..................................................................................................................... 70 Network Setup..................................................................................................................... 71 Email Notification................................................................................................................. 71 Control................................................................................................................................. 71 English 3 Baud Rate ........................................................................................................................... 72 Reset ................................................................................................................................... 72 Using the web control panel ................................................................................................ 73 Using RS232 command by Telnet ....................................................................................... 76 Info menu.................................................................................................................................. 76 ADDITIONAL INFORMATION.......................................................... 77 Compatible resolutions ............................................................................................................. 77 Image size and projection distance .......................................................................................... 91 Ceiling mount installation.......................................................................................................... 94 Projector dimensions........................................................................................................... 94 Ceiling mount information.................................................................................................... 94 IR remote codes ....................................................................................................................... 95 Troubleshooting ........................................................................................................................ 97 LED status indicators................................................................................................................ 98 Specifications ........................................................................................................................... 99 Manual Warp Control Instruction ............................................................................................. 100 Optoma global offices.............................................................................................................. 103 4 English SAFETY The lightning flash with arrow head within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Please follow all warnings, precautions and maintenance as recommended in this user manual. Important safety instructions Do not block any ventilation openings. To ensure reliable operation of the projector and to protect from overheating, it is recommended to install the projector in a location that does not block ventilation. As an example, do not place the projector on a crowded surface. Do not put the projector in an enclosure such as a book case or a cabinet that restricts air flow. To reduce the risk of fire and/or electric shock, do not expose the projector to rain or moisture. Do not install near heat sources such as radiators, heaters, stoves or any other apparatus such as amplifiers that emits heat. Do not let objects or liquids enter the projector. They may touch dangerous voltage points and short out parts that could result in fire or electric shock. Do not use under the following conditions: ± In extremely hot, cold or humid environments. (i) Ensure that the ambient room temperature is within 0°C~40°C (32°F~104°F) (ii) Relative humidity is 10% ~ 85% ± In areas susceptible to excessive dust and dirt. ± Near any appliance generating a strong magnetic field. ± In direct sunlight. Do not use the unit if it has been physically damaged or abused. Physical damage/abuse would be (but not limited to): ± Unit has been dropped. ± Power supply cord or plug has been damaged. ± Liquid has been spilled on to the projector. ± Projector has been exposed to rain or moisture. ± Something has fallen in the projector or something is loose inside. Do not place the projector on an unstable surface. The projector may fall over resulting in injury or the projector may become damaged. Do not block the light coming out of the projector lens when in operation. The light will heat the object and cause it to melt, burn or start a fire. Please do not open or disassemble the projector as this may cause electric shock. Do not attempt to service the unit yourself. Opening or removing covers may expose you to dangerous voltages or other hazards. Please call Optoma before you send the unit for repair. See projector enclosure for safety related markings. The unit should only be repaired by authorized service personnel. Only use attachments/accessories specified by the manufacturer. Do not look straight into the projector lens during operation. The bright light may harm your eyes. Turn off and unplug the power plug from the AC outlet before cleaning the product. Use a soft dry cloth with mild detergent to clean the projector housing. Do not use abrasive cleaners, waxes or solvents to clean the unit. English 5 Disconnect the power plug from the AC outlet if the product will not be used for a long period of time. Do not setup the projector in places where it might be subjected to vibration or shock. Do not touch the lens with bare hands. Do not clean the lens when the projector is turned on. Any damage resulting from doing so will void the warranty. Remove battery/batteries from remote control before storage. If the battery/batteries are left in the remote for long periods, they may leak. Do not use or store the projector in places where smoke from oil or cigarettes may be present, as it can adversely affect the quality of the projector performance. Please follow the correct projector orientation installation as non standard installation may affect the projector performance. Use a power strip and/or surge protector. As power outages and brown-outs can KILL devices. Warning: Do not remove the earthing pin on the mains plugs. This apparatus is equipped with a three prong earthing type mains plug. This plug will only fit an earthing-type mains socket. This is a safety feature. If you are unable to insert the plug into the mains socket, contact an electrician. Caution: This equipment is equipped with a three-pin grounding-type power plug. Do not remove the grounding pin on the power plug. This plug will only fit a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact an electrician. Light Intensity Hazard Distance This product is classified as CLASS 1 LASER PRODUCT - RISK GROUP 2 of IEC 60825-1 : 2014 and also complies with 21 CFR 1040.10 and 1040.11 except for conformance as a Risk Group 2 LIP as defined in IEC 62471-5:Ed. 1.0. For more information, see Laser Notice No. 57, dated May 8, 2019. When set up with BX-CTA13 lens (throw ratio greater than 2.92), this projector may become Class 1 Laser ProductRisk Group 3 (RG3); with other lens (throw ratio less than 2.92), this projector may become Class 1 Laser ProductRisk Group 2 (RG2) according to IEC 60825-1:2014 and IEC 62471-5: 2015, and also make a variance approvals under 21 CFR 1010.4 for RG3 LIP according to Classification and Requirements for Laser Illuminated Projectors (LIPs) (Laser Notice No. 57). Projection Lens BX-CAA01/ BX-CTA01 BX-CAA03/ BX-CTA03 BX-CAA06/ BX-CTA06 BX-CTA15 BX-CTA16 BX-CTA17 Throw Ratio 0.95-1.22 1.52-2.92 1.22-1.52 0.75-0.95 0.361(120") 0.65-0.75 Classification and Requirements for Laser Illuminated Projectors (LIPs) HD: N/A IEC 62471-5: 2015 IEC 60825-1: 2014 CLASS 1 LASER PRODUCT RISK GROUP 2 Projection Lens Throw Ratio BX-CTA13 2.9-5.5 Classification and Requirements for Laser Illuminated Projectors (LIPs) IEC 62471-5: 2015 HD: 2.55 meters IEC 60825-1: 2014 CLASS 1 LASER PRODUCT RISK GROUP 3 Laser radiation safety information To ensure safe operation, read all laser safety precautions before installing and operating the projector. This projector is class 1 laser product of IEC/EN 60825-1:2014 and risk group 2 with the requirements of IEC 62471-5:2015. This projector uses extremely high brightness laser. Do not stare directly into the light beam, as the extremely high brightness may cause permanent eye damage. (Risk Group 2 of IEC 62471-5:2015). No direct exposure to the beam shall be permitted. (Risk Group 3 of IEC 62471-5:2015). 6 English This product is not for household use. Possibly hazardous optical radiation emitted from this product. This projector has a built-in Class 4 laser module. Never attempt to disassemble or modify the laser module. Any operation or adjustment not specifically instructed in the User manual creates the risk of hazardous laser radiation exposure. Do not stare into beam when the projector is on. When turning on the projector, make sure no one within projection range is looking into the lens. Follow the control, adjustment, or operation procedures to avoid damage or injury from exposure to laser radiation. The instructions for the assembly, operation, and maintenance include clear warnings to avoid possible exposure to hazardous laser radiation. We recommend you install this projector above the reach of children. Notice is given to supervise children and to never allow them to stare into the projector beam at any distance from the projector. Notice is given to use caution when using the remote control for starting the projector while in front of the projection lens. Notice is given to the user to avoid the use of optical aids such as binoculars or telescopes inside the beam. Product safety labels Light beam related safety labels Label image Label description "WARNING: MOUNT ABOVE THE REACH AND SIGHT OF CHILDREN." The use of a ceiling mount is recommended with this product to place it above the eye level of children. Additional warning against eye exposure for close exposures less than 1 m. Optoma Technology Inc. 47697 Westinghouse Drive, Fremont, CA 94539, USA This product is in conformity with performance standards for laser products under 21 CFR 1040, except with respect to those characteristics authorized by Variance Number FDA-2021-V-1350 effective on October 2, 2022. U.S.A. Only FDA laser variance (US projectors only) IEC/EN 60825-1:2014 CLASS 1 LASER PRODUCT RISK GROUP 2 Complies with 21 CFR 1040.10 and 1040.11 except for conformance as a Risk Group 2 LIP as defined in IEC 62471-5:Ed. 1.0. For more information see Laser Notice No. 57, dated May 8, 2019. IEC/EN 60825-1:2014 PRODUIT LASER DE CLASSE 1 GROUPE DE RISQUE 2 Conforme aux normes 21 CFR 1040.10 et 1040.11, à l'exception de la conformité en tant que LIP du groupe de risque 2 définie dans la CEI 62471-5: Ed. 1,0. Pour plus d'informations, voir l'avis au laser n ° 57 du 8 mai 2019. IEC/EN 60825-1:2014 1 RG2 IEC 62471-5:Ed.1.0 RG2 LIP 1040.11 2019 5 8 57 IEC/EN 60825-1:2014 1 RG2 IEC 62471-5:Ed.1.0 RG2 LIP 1040.11 2019 5 8 57 21 CFR 1040.10 21 CFR 1040.10 This product is classified as Class 1 Laser Product-Risk Group 2 of IEC 60825-1:2014 and also complies with 21 CFR 1040.10 and 1040.11 as a Risk Group 2, LIP (Laser Illuminated Projector) as defined in IEC 62471-5:Ed.1.0. For more information, see Laser Notice No. 57, dated May 8, 2019. This projector may become Risk Group 3 product when an interchangeable lens with throw ratio greater than 2.92 is installed. Refer to the manual for the lens list and hazard distance before operation. Such combinations of projector and lens are intended for professional use only, and are not intended for consumer use. Not for household use. No direct exposure to beam shall be permitted, which can cause injury to the retina in the back of the eye. As with any bright light source, do not stare into the beam, RG2 IEC 62471-5:2015 English 7 Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. © Copyright 2022 Disclaimer The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes. Trademark recognition Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations and pending applications in other countries throughout the world. HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. DLP®, DLP Link and the DLP logo are registered trademarks of Texas Instruments and BrilliantColorTM is a trademark of Texas Instruments. HDBaseTTM and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance. All other product names used in this manual are the properties of their respective owners and are Acknowledged. FCC This device has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the device and receiver. Connect the device into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/television technician for help. Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations. Caution Changes or modifications not expressly approved by the manufacturer could void the user's authority, which is granted by the Federal Communications Commission, to operate this projector. Operation conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference and 2. This device must accept any interference received, including interference that may cause undesired operation. Notice: Canadian users This Class A digital apparatus complies with Canadian ICES-003. Remarque à l'intention des utilisateurs canadiens Cet appareil numerique de la classe A est conforme a la norme NMB-003 du Canada. 8 English Declaration of conformity for EU countries EMC Directive 2014/30/EU (including amendments) Low Voltage Directive 2014/35/EU Radio Equipment Directive 2014/53/EU (if product has RF function) RoHS Directive 2011/65/EU WEEE Disposal instructions Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please recycle it. English 9 INTRODUCTION Package overview Carefully unpack and verify that the projector comes with all the standard accessories shown below. Some accessories may not be available depending on the projector model, specification and your region of purchase. The warranty card is only supplied in specific regions. Please check with your place of purchase or consult your dealer for more information. Standard accessories Projector Remote control(*) Power lead Quick Start User Manual Warranty Card(**) Documentation Lens ring for BX-CAA01/ BX-CAA03/ BX-CTA13 Lens ring for BX-CAA06/BX-CTA06 Note: (*)The remote control requires two AAA batteries. See Installing/replacing the batteries on page 27 for more information. (**) For European warranty Information, please visit www.optoma.com. Please scan the OPAM warranty QR code or visit the following URL: https://www.optoma.com/us/support/warranty-and-return-policy/ Please scan the QR code or visit the following URL: https://www.optoma.com/support/download 10 English INTRODUCTION Optional accessories Optional lens BX-CAA01/BX-CTA01 (0.95-1.22) Optional lens BX-CAA03/BX-CTA03 (1.52-2.92) Optional lens BX-CAA06/BX-CTA06 (1.22-1.52) Optional lens BX-CTA13 (2.9-5.5) Optional lens BX-CTA15 (0.75-0.95) Optional lens BX-CTA16 (0.361(120")) Optional lens BX-CTA17 (0.65-0.75) Note: The accessories may vary depending on model, specification and region. English 11 INTRODUCTION Product overview 2 3 4 1 5 7 6 8 13 12 11 10 9 No Item 1. Lens 2. Front IR Receiver 3. Top IR Receiver 4. LED Status Indicators 5. Tilt-Adjustment Feet 6. Ventilation (inlet) 7. Ventilation (outlet) Note: Do not block projector inlet or outlet air vents. No Item 8. Input / Output 9. Power Switch 10. Power Socket 11. Security Bar 12. KensingtonTM Lock Port 13. Keypad 12 English INTRODUCTION Connections Rear I/O panel 1 2 3 4 5 6 7 13 12 11 10 9 8 No IO 1. 12V OUT 2. HDBaseT 3. HDMI OUT 4. HDMI 2 IN 5. HDMI 1 IN 6. DVI-D 7. 3G-SDI IN 8. RS-232C 9. 3D SYNC IN 10. 3D SYNC OUT 11. USB TYPE-A 12. ETHERNET 13. REMOTE IN Type IO port Input signal Output Input signal Input signal Input signal Input signal IO port IO port IO port IO port IO port IO port Cable 12V Cable RJ-45 Cable HDMI Cable HDMI Cable HDMI Cable DVI-D Cable 3G-SDI Cable RS-232C Cable 3D SYNC Cable 3D SYNC Cable USB Cable RJ-45 Cable TRS Cable Note: The USB port is for power (5V; 2A) delivery only. Device Example Device HDBaseT set-top box Screen, Projector, Display device Device Device Device Device of 3G-SDI signal Device Device of 3D signal 3D Emitter Only for power supply Device, Internet Remote control English 13 INTRODUCTION Keypad 1 2 3 4 9 8 7 No 1. Power key 2. MENU 3. EXIT 4. INPUT 5. Arrow keys Item 5 6 No 6. ENTER 7. ZOOM 8. FOCUS 9. LENS Item 14 English INTRODUCTION Remote control Button location 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 No Button Function 1. Power On Turn the projector on. 2. Number Keys 16 3. Info Input numbers (0-9) Display information on the source image. 4. Auto Automatically synchronize the projector to an input source. 5. Enter Confirm an selection. 17 6. Arrow Keys Use arrow keys to navigate through the menu or select the appropriate settings. 18 7. Menu Show the main menu on the screen. 8. Mode Press to select the preset display mode. 9. Bright. (brightness) Set the brightness of the image. 19 10. Lens Shift (horizontal) Adjust the image position horizontally. 20 11. Lens Shift (vertical) Adjust the image position vertically. 21 12. Keystone (horizontal) Adjust a horizontally keystone image. 22 13. Keystone (vertical) Adjust a vertically keystone image. 23 14. Shutter Momentarily turn off/on the screen (AV Mute). 24 15. User 1 Press to assign custom functions. See user guide for more info. 16. Standby Turn the projector off. 17. ID Set the projector address. 18. Input Select an input source manually. 19. Exit Back to the previous menu. 20. Pattern Display the test patterns. 21. Contr. (Contrast) Set the contrast of the image. 22. Focus Adjust the image focus. 23. Zoom In/Zoom Out Adjust the image size. 24. User 2 Press to assign custom functions. See user guide for more info. English 15 SETUP AND INSTALLATION Installing the projection lens Before setting up the projector, install the projection lens in to the projector. IMPORTANT! Before installing or replacing the lens, make sure the projector's power switch is turned off. During lens installation, do not adjust the lens shift, zoom, or focus either using the remote control or the projector keypad. To prevent damage to the lens and avoid personal injury, do not clean the lens when the projector is turned on. Any damage resulting from doing so will void the warranty. Procedure: 1. Rotate the lens cap counterclockwise. Then remove the lens cap. 2. Install the lens into the projector. 16 English SETUP AND INSTALLATION 3. Rotate the lens clockwise to lock the lens in place. 4. Firmly install the lens ring onto the lens. Note: Remove the lens in the reverse order. English 17 SETUP AND INSTALLATION Adjusting the projector position When you select a position for the projector, consider the size and shape of your screen, the location of your power outlets, and the distance between the projector and the rest of your equipment. Follow these general guidelines: Position the projector on a flat surface at a right angle to the screen. Position the projector to the desired distance from the screen. The distance from the lens of the projector to the screen, the zoom setting, and the video format determine the size of the projected image. 360 degree free orientation operation For ceiling mount installations, make sure to leave 30mm (1.2'') between the ceiling mount and the bottom intake vents of the projector. 30 mm or greater gap required for airlow Ceiling Mount Plate 18 English SETUP AND INSTALLATION Allowing proper space around the projector is critical for air circulation and cooling. For 360° installations and multiple projectors, make sure to leave at least 1000mm (39.4'') space around the air intakes and outlet of the projector. 1000mm (39.4'') MINIMUM SIDE CLEARANCE Air Outlet 1000mm (39.4'') MINIMUM SIDE CLEARANCE Air Inlet English 19 SETUP AND INSTALLATION Boresight adjustment Only apply a boresight adjustment in case the overall focus of the projected image is not equally sharp. The boresight adjustment helps to balance the tilt of the lens mount to sharpen the unfocused sections of the image. It tilts the lens holder to parallel the lens plane and the DMD plane. Note: This boresight adjustment process may cause the other areas of the image to slide out of focus. This is totally normal. Required tool For BX-CAA01/BX-CTA01/BX-CAA03/BX-CTA03/BX-CAA06/BX-CTA06 lens, the following tools are required for boresight adjustment: Allen key, hex 4mm For BX-CTA16/ BX-CTA17 lens, the following tools are required: Boresight extender with red rubber ring L-shape socket tool Setting the projector start mode 1. Choose the test pattern of the OSD. Switch to full screen mode. 2. Prepare the test area. Verify that the throw ratio of the installed lens matches the requirements of the installation area (projection distance and screen size). 3. Check that the lens is correctly installed. Performing the boresight adjustment For BX-CAA01/BX-CTA01/BX-CAA03/BX-CTA03/BX-CAA06/BX-CTA06/ BX-CTA13/ BX-CTA15 lens Use the Allen key screwdriver to clockwise or counter-clockwise adjust the three boresight screws. For BX-CTA16/ BX-CTA17 lens The boresight extenders must be installed before installing the BX-CTA16/ BX-CTA17 lens. Note: BX-CTA16 lens setup requires a special support kit. For more information, please refer to the BX-CTA16 lens user manual. 20 English SETUP AND INSTALLATION 1. Use the boresight tool to adjust the three boresight screws. 2. Zoom the lens to its widest opening. 3. Adjust the focus control to search for the best sharpness of the projected image. 4. Zone A/C boresight adjustment. If zone C is in focus on the screen, please check the focal plane of zone A. If clear position is just on the screen then no need to adjust. If clear position is out of the screen (Close to the projector), rotate screw 1 CCW and then screw 2 & 3 CW for half amount that 1 rotated. Then repeat until both A and C are clear. For example, turn 1 CCW in a circle, then turn 2 & 3 CW in half circle). If clear position is in the screen (away from the projector), rotate screw 1 CW and then screw 2 & 3 CCW for half amount that 1 rotated. Then repeat until both A and C are clear. 3 2 1 3 1 2 English 21 SETUP AND INSTALLATION 5. Zone D/E boresight adjustment. If zone D is in focus on the screen, please check the focal plane of zone E. If clear position is just on the screen then no need to adjust. If clear position is out of the screen (close to the projector), rotate screw 2 CCW and then screw 1 & 3 CW for half amount that 2 rotated. Then repeat until both D and E are clear. For example, turn 2 CCW in a circle, then turn 1 & 3 CW in half circle). If clear position is in the screen (away from the projector), rotate screw 2 CW and then screw 1 & 3 CCW for half amount that 2 rotated. Then repeat until both D and E are clear. 3 3 2 1 1 2 6. Zone H/I boresight adjustment. If zone H is in focus on the screen, please check the focal plane of zone I. If clear position is just on the screen then no need to adjust. If clear position is out of the screen (close to the projector), rotate screw 3 CCW and then screw 1 & 2 CW for half amount that 3 rotated. Then repeat until both H and I are clear. For example, turn 3 CCW in a circle, then turn 1 & 2 CW in half circle). If clear position is in the screen (away from the projector), rotate screw 3 CW and then screw 1 & 2 CCW for half amount that 3 rotated. Then repeat until both H and I are clear. 22 English 3 2 1 3 1 2 SETUP AND INSTALLATION 7. After the above adjustment of the viewing axis, the projected image from zone A to zone I still cannot achieve a clear focus on the screen. Please remove the PJ-lens then turn the boresight screws 1 to 3 counterclockwise to the end (STOP), and then turn clockwise 2 circles to the design value position. 3 1 2 8. Repeat steps 2 to 6 above to adjust. BX-CTA17 Boresight Tool Operating To mount the ST lens, do the following: Boresight hexagon bars 1. Install the three boresight extenders. 2. Face the socket heads of the extenders towards the projector. English 23 SETUP AND INSTALLATION Boresight adjustment Boresight adjustment is needed if the image is still unsharp after the focus adjustment. The boresight adjustment tilts the lens holder to parallel the lens plane and the DMD plane to fully focus the image on the screen. OR L shape socket tool (black) or U shape socket tool (black) 24 English SETUP AND INSTALLATION Connecting sources to the projector 4 5 67 8 3 2 1 MOLEX 12 11 13 9 No Item 1. Wired Remote-In/Out Cable 2. 12V Trigger Cable 3. RJ-45 Cable 4. HDMI Cable 5. HDMI Cable 6. DVI-D Cable 7. RS-232 Cable 10 No Item 8. 3G-SDI Cable 9. Power Cord 10. 3D Emitter Cable 11. 3D Sync Cable 12. USB Cable 13. RJ-45 Cable English 25 SETUP AND INSTALLATION RS232 Pin assignments 9876 54321 Pin No. 1 2 3 4 5 Signal N/A RXD TXD N/A GND Pin No. 6 7 8 9 Signal N/A N/A N/A N/A Adjusting the projector image Image height The projector is equipped with adjustable feet to change the image height. 1. Locate the adjustable foot you wish to adjust on the underside of the projector. 2. Rotate the adjustable foot clockwise or counterclockwise to raise or lower the projector. Note: The adjustable feet can be raised up to 38mm, or may be removed for certain installations. Please ensure sufficient space around projector for proper air flow. Zoom and Focus Use the remote control or projector keypad to adjust the zoom and focus of the projected image. To adjust the image focus, press Focus and the pq buttons to improve the image quality. A To adjust the image size, press Zoom and the buttons to get the required image size. B A B 26 English SETUP AND INSTALLATION Remote setup Installing / replacing the batteries Two AAA size batteries are supplied for the remote control. 1. Remove the battery cover on the back of the remote control. 2. Insert AAA batteries in the battery compartment as illustrated. 3. Replace back cover on remote control. Note: Replace only with the same or equivalent type batteries. CAUTION Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below. Do not mix batteries of different types. Different types of batteries have different characteristics. Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leakage in old batteries. Remove batteries as soon as the are depleted. Chemicals that leak from batteries that come in contact with skin can cause a rash. If you find any chemical leakage, wipe thoroughly with a cloth. The batteries supplied with this product may have a shorter life expectancy due to storage conditions. If you will not be using the remote control for an extended period of time, remove the batteries. When you dispose of the batteries, you must obey the law in the relative area or country. Remote control ID setup The Infra-Red (IR) remote control supports individual addressing of projectors. The remote receiver on the projector can be set with a specific number from 00 to 99, and the projector only responds to the IR remote set to the same number. The default ID code of the IR remote is 00, allowing it to control all projectors within its effective range. Follow below methods to set up the ID code for the IR remote control: ID Code Change mode 1 Keep pressing the "ID" button for 3 sec, enter "0" then enter "1" within 2 sec, and then release "ID" button. 2 Keep pressing the "ID" button for 3 sec, enter "0" then enter "2" within 2 sec, and then release "ID" button. ... ... 10 Keep pressing the "ID" bottom for 3 sec, enter "1" then enter "0" within 2 sec, and then release "ID" button. 11 Keep pressing the "ID" button for 3 sec, enter "1" then enter "1" within 2 sec, and then release "ID" button. ... ... 98 Keep pressing the "ID" button for 3 sec, enter "9" then enter "8" within 2 sec, and then release "ID" button. 99 Keep pressing the "ID" button for 3 sec, enter "9" then enter "9" within 2 sec, and then release "ID" button. Customer code 3201 3202 3210 3211 3298 3299 To have the IR remote control return to default value 00 where all projectors can be controlled, press the "ID button" for 3 seconds, and press "0" twice within 2 seconds. For more information on setting the remote receivers on the projector, refer to "Remote Setup" on page 70. English 27 SETUP AND INSTALLATION Effective range The Infra-Red (IR) remote control sensors are located on the front and top sides of the projector. To have the remote control function correctly, be sure to hold the remote control at an angle of ±30° horizontally or vertically within the distance of 10m (32.8 ft) to the projector's IR remote control sensor. Make sure that there are no obstacles between the remote control and the IR sensor on the projector. Make sure the IR transmitter of the remote control is not being obstructed by direct light from sunlight or fluorescent lamps. Keep the remote control away from fluorescent lamps for at least 2m or it may malfunction. If the remote control is near Inverter-Type fluorescent lamps, it may operate ineffectively at times. If the remote control and the projector are within a very short distance, it may operate ineffectively. When aiming at a screen, the effective distance is less than 5m from the remote control to the screen and reflects the IR beams back to the projector. However, the effective range may vary between screens. IMPORTANT! If you want to use the 3D IR emitter, refer to "IR Control setup when using the 3D IR emitter" on page 52. Horizontally or Vertically ±30° Horizontally or Vertically ±30° 28 English SETUP AND INSTALLATION Wired remote Remote In connector is designed to work with Wired Remote or IR Keypad with longer range and provides fast, easy set-up and reliable individual control of a specific projector. Remote Out connector sends the IR control signal to the next projector when using multiple projectors. The connector type is 3.5mm Phone Jack connector: Power IR_IN GND English 29 USING THE PROJECTOR Powering on / off the projector Powering on 1. Securely connect the AC power cord and signal/source cable to the projector. 2. Set the power switch to the "I" (ON) position and wait until the power button " " on the projector keypad is solid orange. 3. Turn on the projector by pressing the ON button " " on the remote control or the power button " " on the projector keypad. The status LED is orange with a long blink and the status LED will turn to solid green. or Note: If the projector is turned on for the first time, you will be prompted to select the projector language, projection orientation, and other settings. 30 English USING THE PROJECTOR Powering off 1. Turn off the projector by pressing the power button " " on the projector keypad or the OFF button " " on the remote control. A message will pop up to confirm that you want to turn off the projector. 2. Press the power button or the OFF button again to confirm, otherwise the warning message disappears after 10 seconds and the projector remains on. 3. Set the Power switch to the "o" (OFF) position. The status LED turns from blinking orange to solid orange and the keypad also turns to solid orange. 4. Disconnect the power cord from both the projector and the electrical outlet. Note: It is not recommended to turn on the projector immediately after powering it off. Wait for 10 seconds until you power it on again. Selecting an input source Turn on the connected source that you want to display on the screen, such as computer, notebook, and/or video player. The projector will automatically detect the input source. If multiple sources are connected, press the INPUT button on the remote control or INPUT key on the projector keypad to select an input source. or English 31 USING THE PROJECTOR Menu navigation and features The projector has multilingual on-screen display (OSD) menus that allow you to make image adjustments and change a variety of settings. 1. To open the OSD menu, press the Menu key on the remote control or projector keypad. 2. To select a main menu or submenu, use the p and q buttons to highlight it. Then, press the Enter key to enter the submenu. 3. Press the Exit key to return to the previous menu or exit the OSD menu if at top level. 4. Setting methods to adjust the function value or selection an option. To adjust the slide bar values, highlight the function, and use the t u buttons to change value. To check or uncheck a checkbox, highlight the function, and press Enter. To input a number or symbol, highlight the number or symbol, and use the p and q buttons to make a selection. You can also use the number keys on the remote control or keypad. To select a function option, use the p q t u buttons to make the selection. If no Enter icon shows at the navigation bar, the highlighted option is automatically applied. If there is an Enter icon at the navigation bar, press Enter to confirm your selection. Main menus Submenus Settings 1 Picture Mode 2 Dynamic Range 3 Brightness Contrast 4 Sharpness 5 Gamma Dynamic Contrast 6 Color Settings Wall Color 3D Setup Select No Item 1. Image menu 2. Display menu 3. Input settings menu Image Bright Off Exit Enter Navigation guide No Item 4. Device setup menu 5. Communication menu 6. Information menu 32 English USING THE PROJECTOR OSD menu tree Main Menu Sub Menu 2 Image Picture Mode Sub Menu 3 Sub Menu 4 Dynamic Range HDR HDR Picture Mode Brightness Contrast Sharpness Gamma Dynamic Contrast Dynamic Black Speed Strength Level Extreme Black AV Mute Timer Black Signal Level Sub Menu 5 Sub Menu 6 Values Presentation Bright Cinema HDR sRGB DICOM SIM. Blending 3D 2D High Speed User Off Auto Bright Standard Film Detail 0~100 0~100 1-15 Film Graphics Standard(2.2) Vivid 3D Blackboard DICOM SIM. 1.8 2.0 2.4 2.6 Off On 1~15 0~3 50%~100% Off On 0s~10s 0~5 English 33 USING THE PROJECTOR Main Menu Sub Menu 2 Image Color Settings Sub Menu 3 Color Tint Color Temperature Sub Menu 4 White Balance Red Gain Green Gain Blue Gain Red Offset Green Offset Blue Offset White Enhancement Color Space Color Matching Auto Test Pattern Red Green Blue Cyan Magenta Yellow White Reset Sub Menu 5 Hue Saturation Luminance Hue Saturation Luminance Hue Saturation Luminance Hue Saturation Luminance Hue Saturation Luminance Hue Saturation Luminance Red Green Blue Sub Menu 6 Values 0~100 0~100 Warm Standard Cool 0-100 0-100 0-100 0-100 0-100 0-100 0-10 Auto RGB (0-255) RGB (16-235) REC709 REC601 Off On 0~254 0~254 0~254 0~254 0~254 0~254 0~254 0~254 0~254 0~254 0~254 0~254 0~254 0~254 0~254 0~254 0~254 0~254 0~254 0~254 0~254 Yes / Cancel (Dialog box) 34 English USING THE PROJECTOR Main Menu Sub Menu 2 Image Wall Color Sub Menu 3 3D Setup 3D Mode 3D Format 3D Tech 3D-2D 3D Sync Out 3D Invert Save to User Apply to User Frame Delay Reset Reset Sub Menu 4 Sub Menu 5 Sub Menu 6 Values Off Blackboard Light Yellow Light Green Light Blue Pink Gray Off Active 3D Auto Frame Packing Side by Side Top and Bottom Frame Sequential DLP-link 3D Sync 3D L R To Emitter To Next Projector Off On 1~200 Yes / Cancel (Dialog box) Yes / Cancel (Dialog box) User-Presentation User-Bright User-Cinema User-HDR User-sRGB User-DICOM SIM. User-Blending User-3D User-2D High Speed Yes / Cancel (Dialog box) English 35 USING THE PROJECTOR Main Menu Sub Menu 2 Display Aspect Ratio Sub Menu 3 Digital Zoom Proportional Geometric Correction Horizontal Vertical Horizontal Shift Vertical Shift Reset Warp Control Basic Warp Advanced Warp Sub Menu 4 Sub Menu 5 Sub Menu 6 Keystone Pincushion 4-Corner Grid Color Horizontal Vertical Horizontal Vertical Top Left Top Right Bottom Left Bottom Right Grid Background Warp Setting Grid Points Warp Inner Blend Setting Warp Sharpness Blend Width Overlap Grid Number Gamma Values Auto 4:3 16:9 16:10 LBX Native Off On 50%~400% 50%~400% 0~100 0~100 Yes / Cancel (Dialog box) Basic Advanced AP 0~40 0~40 0~100 0~100 Green Magenta Red Cyan Black Transparent 2x2 3x3 5x5 9x9 17x17 Off On 0~9 4 / 6 / 8 / 10 / 12 1.8 /1.9 /2.0/2.1/2.2/2.3/2.4 36 English USING THE PROJECTOR Main Menu Sub Menu 2 Display Geometric Correction Sub Menu 3 Advanced Warp Memory Edge Mask Freeze Screen Reset Test Pattern Sub Menu 4 Black Level Sub Menu 5 Area Enable Edit Area Brightness Red Green Blue Reset Save Memory Apply Memory Clear Memory Sub Menu 6 Brightness Red Green Blue Exit Bottom Top All Values Bottom Top Off On 0~255 0~255 0~255 0~255 0~255 0~255 Yes / Cancel (Dialog box) Yes / Cancel (Dialog box) Yes / Cancel (Dialog box) Memory 1~Memory 5 Memory 1~Memory 5 Yes / Cancel (Dialog box) Yes / Cancel (Dialog box) 0~10 Unfreeze Freeze Off Green Grid Magenta Grid White Grid White Black Red Green Blue Yellow Magenta Cyan ANSI Contrast 4x4 Color bar Full screen English 37 USING THE PROJECTOR Main Menu Sub Menu 2 Display PIP/PBP Sub Menu 3 Screen Main Source Sub Source Swap Size Location Input Settings Reset Auto Source Quick Resync Active Inputs Latency Adjustment Sub Menu 4 Sub Menu 5 Sub Menu 6 Values Off PIP PBP HDMI1 HDMI2 DVI-D 3G-SDI HDBaseT HDMI1 HDMI2 DVI-D 3G-SDI HDBaseT Small Medium Large PBP, Main Left PBP, Main Top PBP, Main Right PBP, Main Bottom PIP, Bottom Right PIP, Bottom Left PIP, Top Left PIP, Top Right Yes / Cancel (Dialog box) Off On Off On HDMI1 HDMI2 DVI-D 3G-SDI HDBaseT Normal 2D Ultra 38 English USING THE PROJECTOR Main Menu Sub Menu 2 Input Settings Backup Input Sub Menu 3 Auto Switch Current Signal First Input Sub Menu 4 Sub Menu 5 Second Input HDMI Reset Backup Input Status Backup Input Change Backup Input Info. Output Current Signal Backup Input Status Backup Input Change First Input Resolution Horz Refresh Color Space HDR Second Input Resolution Horz Refresh Color Space HDR HDMI 1 EDID HDMI 2 EDID Sub Menu 6 Values Off On (read only) HDMI1 HDMI2 HDBaseT DisplayPort HDMI1 HDMI2 HDBaseT DisplayPort Active/Inactive (read only) Changed/No Change (read only) (read only) Active/Inactive (read only) Changed/No Change (read only) By First Input (read only) (read only) (read only) (read only) Yes/No (read only) By Second Input (read only) (read only) (read only) (read only) Yes/No (read only) HDMI 1 HDMI 2 1.4 2.0 1.4 2.0 Yes / Cancel (Dialog box) English 39 USING THE PROJECTOR Main Menu Sub Menu 2 Device Setup Language Sub Menu 3 Projection Ceiling Rear Lens Settings Focus Zoom Sub Menu 4 Sub Menu 5 Sub Menu 6 Values English Deutsch Français Italiano Español Português Polski Nederlands Norsk Magyar Auto On Off Off On + - Lens Shift Schedule Lens Memory Lens Calibration Lens Lock Save Memory Apply Memory Clear Memory Reset Date and Time Schedule Mode View Today p q t u Memory 1~Memory 5 Memory 1~Memory 5 Yes / Cancel (Dialog box) Yes / Cancel (Dialog box) Lock Unlock Yes / Cancel (Dialog box) ----/--/-- --:-Off / On Monday / Tuesday / Wednesday / Thursday / Friday / Saturday / Sunday 40 English USING THE PROJECTOR Main Menu Sub Menu 2 Device Setup Schedule Sub Menu 3 Monday / Tuesday / Wednesday / Thursday / Friday / Saturday / Sunday Sub Menu 4 Sub Menu 5 Schedule Enable Event 01-16 Time Function Sub Menu 6 Copy Events To Event (Function = Power Settings) (Function = Input Source) (Function = Light Source Mode) (Function = Shutter) Reset Reset Schedule Date and Time Clock Mode Reset the Day Date Time Daylight Saving Time NTP Server Time Zone Values Off On 00:00 ~ 23:59 Off / Power Settings / Input Source / Light Source Mode / Shutter Off Power On / Eco / Active / Communication HDMI1 / HDMI2 / DVI-D / 3G-SDI / HDBaseT Normal Mode / Eco Mode / Custom Brightness Shutter On / Shutter Off Yes / Cancel (Dialog box) Monday / Tuesday / Wednesday / Thursday / Friday / Saturday / Sunday Yes / Cancel (Dialog box) Yes / Cancel (Dialog box) Use NTP Server Manual 2000 ~ 2037 (Year) 01 ~ 12 (Month) 01 ~ 31 (Day) 00 ~ 23 (Hour) 00 ~ 59 (Minute) Off On time.google.com asia.pool.ntp.org europe.pool.ntp.org north-america.pool.ntp.org UTC+14:00 UTC+13:00 UTC+12:45 UTC+12:00 UTC+11:00 UTC+10:30 UTC+10:00 UTC+09:30 UTC+09:00 UTC+08:45 UTC+08:00 UTC+07:00 English 41 USING THE PROJECTOR Main Menu Sub Menu 2 Sub Menu 3 Device Setup Date and Time Time Zone Sub Menu 4 Sub Menu 5 Update Interval Power Settings Apply Power Mode (Standby) Signal Power On Auto Power Off Sleep Timer 12V Trigger Light Source Settings Reset Light Source Mode Custom Brightness Brightness Level Constant Brightness Sub Menu 6 Values UTC+06:30 UTC+06:00 UTC+05:45 UTC+05:30 UTC+05:00 UTC+04:30 UTC+04:00 UTC+03:30 UTC+03:00 UTC+02:00 UTC+01:00 UTC+00:00 UTC-01:00 UTC-02:00 UTC-03:00 UTC-03:30 UTC-04:00 UTC-05:00 UTC-06:00 UTC-07:00 UTC-08:00 UTC-09:00 UTC-09:30 UTC-10:00 UTC-11:00 UTC-12:00 Hourly Daily Yes / Cancel (Dialog box) Eco Active Communication Off On 0~180 m 0~16 h Off On Yes / Cancel (Dialog box) Normal Eco Mode Custom Power 30%~100% Off On 42 English USING THE PROJECTOR Main Menu Sub Menu 2 Device Setup Shutter Sub Menu 3 Fade-In Fade-Out Startup Sub Menu 4 Sub Menu 5 Security Security On Screen Display Security Timer Change Password Menu Location Month Day Hour Menu Transparency Menu Timer Information Hide Background Logo Setup Change Logo Backlight Logo Capture Delete Logo Keypad Captured Logo User Logo Power key High Altitude User Data Save all settings Load all settings System Update Auto (FOTA) Update Sub Menu 6 Values 0.5~5s 0.5~5s Shutter Off Shutter On Off On 0-35 0-29 0-23 Top Left Top Right Center Bottom Left Bottom Right 0~9 Off 5s 10s 15s 30s 60s Off On Blue Black White Logo Default Logo Neutral User Logo Captured Logo Yes / Cancel (Dialog box) Yes / Cancel (Dialog box) Yes / Cancel (Dialog box) Off On Off On Off On Memory 1~Memory 5 Memory 1~Memory 5 On Off Yes / Cancel (Dialog box) English 43 USING THE PROJECTOR Main Menu Sub Menu 2 Device Setup Reset Communication Projector ID Remote Setup Sub Menu 3 Reset OSD Reset to default Reset Selective Remote Code Quick Switch Code Sub Menu 4 Sub Menu 5 Image Display Input Communication Setup IR Function Front Top HDBaseT User 1 User 2 44 English Network Setup LAN Interface MAC Address Network Status DHCP IP Address Subnet Mask Gateway DNS Apply Network Reset Sub Menu 6 Values Yes / Cancel (Dialog box) Yes / Cancel (Dialog box) Yes / Cancel (Dialog box) Yes / Cancel (Dialog box) Yes / Cancel (Dialog box) Yes / Cancel (Dialog box) Yes / Cancel (Dialog box) 0~99 0~99 Off 1~9 Off On Off On Off On Freeze Screen Blank Screen PIP/PBP Aspect Ratio Information Hide Network setup Projector ID Color Matching Reset Selective Freeze Screen Blank Screen PIP/PBP Aspect Ratio Information Hide Network setup Projector ID Color Matching Reset Selective RJ-45 HDBaseT (read only) (read only) Connected / Disconnected Off On - - - . - - - . - - - . - - - - - . - - - . - - - . - - - - - . - - - . - - - . - - - - - . - - - . - - - . - - Yes / Cancel (Dialog box) Yes / Cancel (Dialog box) USING THE PROJECTOR Main Menu Sub Menu 2 Communi- Email cation Notification Control Sub Menu 3 Email 1 Email 2 Event Fan Error Power On/Off Video Loss Laser Reset Crestron Sub Menu 4 IP Address IPID Port Crestron Setup Apply PJ Link Authentication Password Service PJ Link Setup Apply Extron AMX Telnet HTTP Baud Rate Reset Serial Port In Reset Sub Menu 5 Sub Menu 6 Values Email 1 Address (read only) Email 1 Address (read only) Off/Email Off/Email Off/Email Off/Email Yes / Cancel (Dialog box) Off On - - - . - - - . - - - . - - 2~255 0~65535 Yes / Cancel (Dialog box) Off On Off On (read only) - - - . - - - . - - - . - - Yes / Cancel (Dialog box) Off On Off On Off On Off On Yes / Cancel (Dialog box) 1200 2400 4800 9600 19200 38400 57600 115200 Yes / Cancel (Dialog box) English 45 USING THE PROJECTOR Main Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Information Device Regulatory Serial Number Projection Hours System Status Standby Mode Light Source Mode Light Source Hours Total Hours Normal Eco Mode Custom Power Temperature AC Voltage Communication Projector ID Remote Code LAN Interface MAC Address Network Status DHCP IP Address Subnet Mask Gateway DNS Crestron Extron PJ Link AMX Telnet HTTP Signal Input Signal Resolution Signal Format Pixel Clock Horz Refresh Vert Refresh Color Space Picture Mode Second Signal Resolution Signal Format Pixel Clock Horz Refresh Vert Refresh Color Space Sub Menu 5 Sub Menu 6 Values 46 English USING THE PROJECTOR Main Menu Sub Menu 2 Information Backup Input Firmware Version Sub Menu 3 Sub Menu 4 Current Signal Backup Input Status Backup Input Change First Input Resolution Horz Refresh Color Space HDR Second Input Resolution Horz Refresh Color Space HDR Main Version I-SCALER Version F-MCU Version M-MCU Version L-MCU Version A-MCU Version K-MCU Version LAN Version Formatter Version FPGA0 Version FPGA1 Version FPGA2 Version XFPGA Version HDBaseT Version Camera Version Sub Menu 5 Sub Menu 6 Values English 47 USING THE PROJECTOR Image menu Learn how to configure image settings. Submenus Picture Mode Dynamic Range Brightness Contrast Sharpness Gamma Dynamic Contrast Color Settings Wall Color 3D Setup Picture Mode Picture Mode menu provides various functions to optimize the projected image to achieve the best image quality in all kinds of surroundings, in consideration of factors such as input source, screen color, and ambient lighting. Presentation Best for displaying presentation slides in a bright room. Bright Best for the installations requiring high brightness images. Cinema Best for videos projected in a dark room. HDR Best for displaying High Dynamic Range (HDR) content. sRGB Standardized image color that matches the sRGB color standard. DICOM SIM. Best for projecting monochrome medical images, such as X-ray diagram. Blending Best for multiple projector installations. 3D Best for playing 3D videos. 2D High Speed Display the status of 2D High Speed mode (This mode should not be used for medical diagnosis). Note: If the resolution of the input source is 800 x 600 @120Hz, 1024 x 768 @120Hz, or 1280 x 720 @120Hz, then the display mode will automatically switch to 2D High Speed then the 3D mode, PIP/PBP modes are not supported. 48 English USING THE PROJECTOR User Image settings saved by the user. Dynamic Range Configure the HDR setting and its effect when displaying video from 4K Blu-ray players and streaming devices. HDR Enable or disable HDR processing. HDR Picture Mode Bright: Select this mode for more saturated colors. Standard: Select this mode for natural looking images. Film: Select this mode for improved detail. Detail: Select this mode for more detail in dark scenes. Brightness Adjust the luminous brightness of the projected image to adapt to different ambient light. Contrast Adjust the contrast ratio of the projected image. The contrast controls the degree of difference between the lightest and darkest parts of the image. Sharpness Adjust the clarity of details in the projected image to make the image clearer and sharper. Gamma Select an appropriate gamma value to optimize the image conformance to different input sources. Film Best for home theater setting. Graphics Best for projecting photos from PC input. Standard (2.2) Standard gamma value. Vivid Best for playing games. In this mode, color saturation and brightness are well-balanced. 3D Best for playing 3D videos. Blackboard Best for projecting on to a blackboard. DICOM SIM. Best for projecting monochrome medical images, such as X-ray diagram. 1.8 / 2.0 / 2.4 / 2.6 Select a preset gamma value to adjust the image performance. In general, the smaller the value, the brighter the dark areas of the image will become. English 49 USING THE PROJECTOR Dynamic Contrast Set up Dynamic Contrast to maximize the contrast for dark content. Dynamic Black Enable this function to automatically adjust the contrast ratio for video sources. It improves the black level in dark scenes by reducing the light output. Speed: Adjust the speed of the light source correction. The value ranges from 1 to 15. A lower value makes the correction slower and less aggressive while a higher value results in the faster correction. Strength: Set the strength of the dynamic contrast adjustment. The value ranges from 0 to 3, the higher the value the stronger the correction. Level: Adjust the light source when the brightness level of the current content gets lower than the set value. The value ranges from 50% to 100%. The higher the value, the larger the range to adjust the light source. Extreme Black Enable this function to automatically increase the contrast ratio by turning off the laser light when black image is detected. AV Mute Timer: Set a timer for the laser light to turn off after detecting black content. The set value ranges from 0s to 10s. Black Signal Level: Set a black level value as the threshold for the Real Black function. The value can be adjusted from 0% to 5%, with 0 being the darkest black and 5 being the brightest. Color Settings Configure the color settings of the projected image to improve the color performance. Green Chromaticity Diagram Yellow Cyan White Red Blue Magenta Color Adjust the saturation of the selected color. The value indicates the color shifts from or towards the white in the center of the chromaticity diagram. Tint Adjust the color balance of red and green in video images. Color Temperature Adjust the color temperature of the projected image. The available options are Warm, Standard, and Cool. 50 English USING THE PROJECTOR White Balance Adjust the white balance of the projected image via gain and offset. Gain and offset are individual controls for each RGB channels used to set greyscale. The Gains calibrate the color of the dark parts and Bias calibrate the white parts. Red / Green / Blue Gain: Adjust the color of the image's bright areas. Red / Green / Blue Offset: Adjust the color of the image's dark areas. White Enhancement Adjust the image color brightness while providing more vibrant colors, in increments from 0 to 10. Color Space Select a color space that has been specifically tuned for the input signal. The available options are Auto, RGB (0~255), RGB (16~235), REC709, and REC601. Note: The Color Space function is grayed out if the Picture Mode is sRGB or without any source input. Color Matching Change the color of a projected image by adjusting each color component in the image. The adjustable color includes Red, Green, Blue, Cyan, Yellow, and Magenta (R / G / B / C / Y / M). Auto Test Pattern: Enable the function to view a specific color pattern while adjusting. Red / Green / Blue / Cyan / Magenta / Yellow: Select a color for further adjustment. ± Hue: Adjust the hue of the selected color. The value reflects the number of degrees of rotation around the chromaticity diagram from the original color. Increasing value indicates counterclockwise rotation, and decreasing value, clockwise rotation. ± Saturation: Adjust the saturation of the selected color. The value reflects the color shifts from or towards the white in the center of the chromaticity diagram. ± Luminance: Adjust the luminance of the selected color. Increase the value to brighten the image (add white to a color) or decrease the value to darken the image (add black to a color). White: Adjust the white color performance via setting the Red, Green, and Blue values. ± Red / Green / Blue: Adjust the red, green, and blue colors to optimize the white color performance. Reset: Reset the function settings to factory default values. Wall Color Set the wall color of the projector to achieve best color performance for a specific wall. The available options are Off, Blackboard, Light Yellow, Light Green, Light Blue, Pink, and Gray. 3D Setup 3D video file combines two slightly different images (frames) of the same scene representing the different views that the left and right eyes see. When these frames are displayed fast enough and viewed with 3D glasses synchronized with the left and right frames, the viewer's brain then assemble the separate images into a single 3D image. 3D Menu provides options to set up the 3D functions to correctly display 3D videos. 3D Mode Enable or disable the 3D function. 3D Format Select a proper 3D format for the 3D input signal. The available options are Auto, Frame Packing, Side by Side, Top and Bottom, and Frame Sequential. English 51 USING THE PROJECTOR 3D Tech Select a proper 3D technology according to how the 3D sync signal is processed. DLP-Link: Select DLP-Link when the 3D sync signal is generated by the DLP Link technology built into the projector. DLP Link works only with the glasses that are compatible with DLP 3D technology and the 3D function is enabled 3D Sync: Select 3D Sync when the 3D sync out signal is sent to an emitter or another projector through the 3D sync out port. 3D-2D Transform the 3D content to 2D images. 3D: Play the 3D content normally. L: Play the left images of the 3D content. R: Play the right images of the 3D content. 3D Sync Out Set up the transmission of the 3D sync output signal. To Emitter: Send the 3D sync signal to the emitter connected to the 3D sync out port. To Next Projector: Send the 3D sync signal to next projector when using multiple projectors. IR Control setup when using the 3D IR emitter Infrared devices interfere with each other if placed in the same sensing angle. If you want to use the 3D IR emitter and the IR remote function, do any of the following: Place the 3D IR emitter outside the IR remote control sensing angle as shown below: Horizontally or Vertically ± 30° 3D IR emitter direction NG 3D IR emitter direction OK 3D IR emitter direction NG Horizontally or Vertically ± 30° Based on the room layout, disable either the front or the top remote receiver in the OSD menu > Communication > Remote Setup > IR Function menu to avoid the 3D IR emitter interference, yet allowing to use the IR remote control function. 52 English USING THE PROJECTOR If neither of the two methods described above solved the problem, please use another 3D IR emitter/3D RF emitter or try any of the following two methods. Use a wired remote-in cable for the IR control. Use the IR control via the HDBaseT device (not supplied). Note: Disable the Front/Top remote receivers and enable the HDBaseT for IR control in the OSD menu > Communication > Remote Setup > IR Function. 3D Invert When the 3D video does not appear correctly, use this function to invert the 3D left and right frames. Frame Delay Set a frame delay value for the projector to correct the time difference between the 3D signal being given and the result being executed. This function works only when L/R Reference is set to Field GPIO. When performing 3D blending on multiple projectors, set the frame delay for each projector to correct the nonsynchronous images. Reset Reset the function settings to factory default values. Save to User Save the image settings to the User mode. Apply to User Apply the image settings to User-Presentation, User-Bright, User-Cinema, User-HDR, User sRGB, User-DICOM SIM., User-Blending, User-3D, or User-2D High Speed. Reset Reset all 3D settings. English 53 USING THE PROJECTOR Display menu Learn how to configure the settings to properly project images according to your installation circumstances. Submenus Aspect Ratio Digital Zoom Geometric Correction Edge Mask Freeze Screen Test Pattern PIP/PBP Aspect Ratio Set the aspect ratio of the projected image. The available options are Auto, 4:3, 16:9, 16:10, LBX, or Native. Select Auto to display the detected image size. Digital Zoom Digitally adjust the size of the projected image. Note: Image projection on the screen depends on the signal source.. Proportional Enable the function to have the image's height and width changed at the same ratio. Horizontal Use the t and u buttons to change the width of the projected image. Vertical Use the p and q buttons to change the height of the projected image. Horizontal Shift Use the t and u buttons to horizontally shift the image. Vertical Shift Use the p and q buttons to vertically shift the image. Reset Reset digital zoom settings to factory default values. 54 English USING THE PROJECTOR Geometric Correction Configure the geometric settings to reshape the image for different projection surfaces. Warp Control Configure warp settings. Select between Basic, Advanced, and AP. Basic: Configure keystone, pincushion, 4-corner settings. Advanced: Set the grid color and grid background, as well as configure warp and blend settings. AP: Use the Visual Suite to control the projector. When the Visual Suite is enabled, the projector's built in geometry functions are disabled. Basic Warp Configure basic warp settings. Keystone: Keystone function is used to adjust the images in asymmetric rectangle shape. ± Horizontal: Adjust the left and right side of the projected image to make it an even rectangle. It is used for the images with unequal left and right sides. ± Vertical: Adjust the top and bottom side of the projected image to make it an even rectangle. It is used for the images with unequal top and bottom sides. Pincushion: Pincushion function is used to adjust the image with barrel or pincushion distortion. ± Horizontal: Correct the projected image with horizontal barrel or pincushion distortion. ± Vertical: Correct the projected image with vertical barrel or pincushion distortion. English 55 USING THE PROJECTOR 4-Corner: Reshape the image by moving the 4 corners of the image to have it fit a specific projection surface. Advanced Warp Configure advanced warp settings. Refer to "Manual Warp Control Instruction" on page 100. Note: When Basic or AP of Warp Control is selected, the Advanced Warp will be unavailable. Grid Color: Select a grid color for warp and blend pattern between Green, Magenta, Red, and Cyan. Grid Background: Select the grid background between Black and Transparent. Warp Setting: Configure warp settings. ± Grid Point: The grid number selection of warping control, 2x2 / 3x3 / 5x5 / 9x9 / 17x17. ± Warp Inner: Turn on to adjust the inner grid, the function activates when exceeding 3x3 grid points. ± Warp Sharpness: When the grid lines are warped from straight into curve, the grid lines will be distorted and become jagged. To avoid the line jagging, adjust the warp sharpness to blur or sharpen the edge of the images. Blend Setting: Configure the blend settings directly on the projector to merge two or more adjacent images into one larger and seamless image. ± Blend Width: Set the blend pattern width. ± Overlap Grid Number: Set adjustment scale of blend width, up to 12 pixels. ± Gamma: Select the gamma value of the blend area to adjust the curvature of the blending effect. Note: For install flexibility we have not applied a FW limitation to the blending menu of this device. Distortion may occur if you attempt to warp to an extreme level. For more complex installs, at a cost, please contact your dealer for external devices for warping. Width Start pixel Blend area Gamma 56 English USING THE PROJECTOR Black Level: Manually adjust the black level of the projected image. ± Area: Support two layers black level adjustment, top and bottom. Please avoid overlapping areas of the two layers, only top black level value displayed in overlapping area. ± Enable: Enable or disable the black level adjustment in the selected area. ± Edit Area: The area adjustment of black level. When entering the area adjustment view, user can press "INFO" button on remote control to get the hot key for add and remove points. ± Add Point: Add up to 32 area control points for black level adjustment. ± Remove Point: Remove at least 4 control points from the selected area. Note: Enter the Edit Area: a) Use the "INPUT" hotkey of the remote control to enable or disable the Add Point function. b) Use the "AUTO" hotkey of the remote control to enable or disable the Remove Point function. c) Use the "INFO" hotkey of the remote control to show the Edit Area's hotkey help dialog, and use "MENU" or "Exit" to hide help dialog. After adding or removing a control point, press Enter to move to the next point counterclockwise. ± Brightness: Adjust Red / Green / Blue values of selected black level area simultaneously. ± Red/Green/Blue: Adjust each color of selected black level area individually. ± Reset: Reset the black level to factory default values either on the Bottom or on the Top area or on both areas. Memory The projector allows the user to save up to five geometry memories, including the ones set directly on the projector and the ones configured via external software tools. The available options are Save Memory, Apply Memory, and Clear Memory. Reset Reset geometric settings to factory default values. Edge Mask The edge blending function allows you to hide one or multiple edges of the projected image. You can use this function to remove the video encoding noise on the edges of the video images. Freeze Screen Select to pause the display screen despite any change in the source device. Test Pattern Select a test pattern. The available options are Off, Green Grid, Magenta Grid, White Grid, White, Black, Red, Green, Blue, Yellow, Magenta, Cyan, ANSI Contrast 4x4, Color bar, and Full screen. English 57 USING THE PROJECTOR PIP/PBP PIP/PBP (picture in picture/picture by picture) allows simultaneously displaying two images from two input sources. Screen Select the appropriate PIP/PBP mode or disable the function. Off: Disable PIP/PBP mode. PIP: Display one input source on the main screen and the other input source in an inset window. PBP: Display two images of the same size on the screen. Main Source Select an input source for the main image. The available input sources are HDMI1, HDMI2, DVI-D, 3G-SDI, and HDBaseT. Sub Source Select an input source for the second image. The available input sources are HDMI1, HDMI2, DVI-D, 3G-SDI, and HDBaseT. Swap Swap the main source and sub source. Size Change the display size of the sub source in PIP mode. Location Adjust the location of the sub image. In the layout chart below, the "P" indicates the main image: PBP Layout PBP, Main Left PBP Layout PBP, Main Right P P PBP, Main Top P PIP Layout PIP Layout PIP, Bottom Right Small P PBP, Main Bottom P PIP Size Medium P Large P P P P PIP, Bottom Left PIP, Top Left P P P 58 English USING THE PROJECTOR PIP Layout PIP, Top Right Small P PIP Size Medium P Note: Refer to the table below for PIP/PBP compatibility. PIP/PBP Compatibility PIP/PBP Matrix DVI-D HDMI-1 HDMI-2 3G-SDI HDBaseT DVI-D -- V V V V HDMI-1 V -- V V V HDMI-2 V V -- V V 3G-SDI V V V -- V Reset Reset all the display settings to factory default values. Large P HDBaseT V V V V -- English 59 USING THE PROJECTOR Input Settings menu Learn how to configure the projector input settings. Submenus Auto Source Quick Resync Active Inputs Latency Adjustment Backup Input HDMI HDBaseT Auto Source When Auto Source is enabled, the projector automatically detects and selects the input signal. Once an input source is selected, press the Input button on the remote control or keypad to switch to other available sources. When the function is disabled, pressing Input will bring up the Active Inputs submenu. Quick Resync Enable this feature to perform a quick process for synchronizing the projector with the input signal. Active Inputs Select an input signal from the source list. The available input sources are HDMI1, HDMI2, DVI-D, 3G-SDI, and HDBaseT. Latency Adjustment Enable this feature to reduce response time. Note: If the latency adjustment is set to 2D Ultra then the 3D mode, PIP modes, and 4K 30Hz resolution are not supported. Backup Input Backup Input function allows the user to set up two input sources with the same timing specification. Upon loss of one input source, the projector automatically switches to the other source. This function can be useful for the installations requiring uninterruptedly displaying the content source, such as live show, exhibition, and critical control room. The available input sources are HDMI1, HDMI2, DVI, and HDBaseT. Auto Switch Check the box to enable automatically switching to the backup input source when the current source fails. Current Signal Displays the current active signal. First Input Select a signal as the first input source. Once the selected source is activated, the OSD menu lists out the signal's Resolution, Horz Refresh (horizontal refresh rate), and Color Space. Second Input Select a signal as the second input source. Once the selected source is activated, the OSD menu lists out the signal's Resolution, Horz Refresh (horizontal refresh rate), and Color Space. 60 English USING THE PROJECTOR Backup Input Status Display the function status. The Backup Input Status is active when meeting the following conditions: Auto Switch is checked. The two sources are with the same timing specification. The two sources are active. Projector is displaying one of the two sources. Backup Input Change Display the function change. Backup Input Info. Display the function information, including Current Signal, Backup Input Status, Backup Input Change, First Input and its Resolution, Horz Refresh, Color Space, HDR, Second Input and its Resolution, Horz Refresh, Color Space, and HDR. HDMI Setup the projector's HDMI ports. Output Select a HDMI port to output the signal. HDMI 1 EDID/HDMI 2 EDID When receiving a HDMI signal, set the projector's EDID compatibility to display the signal correctly. Select 1.4 for the input devices with HDMI 1.4, or 2.0 for HDMI 2.0 devices. Reset Reset all the input settings to factory default values. English 61 USING THE PROJECTOR Device Setup menu Learn how to configure the system settings for the projector. Submenus Language Projection Lens Settings Schedule Date and Time Power Settings Light Source Settings Shutter Security On Screen Display Logo Setup Backlight High Altitude User Data System Update Language Select a language for the OSD menu. The available languages are English, German, French, Italian, Spanish, Portuguese, Polish, Dutch, Norwegian, Traditional Chinese, Simplified Chinese, Japanese, Korean, Russian, Hungarian, and Thai. Projection Change the image direction by selecting a proper projection mode. Ceiling Enable the function for ceiling mount installation. Rear Check the function for rear projection. Lens Settings Configure the lens settings to adjust the image quality and position. Focus Use the p and q buttons to adjust the focus of the projected image. Zoom Use the and buttons to adjust the size of the projected image. Lens Shift Use the p q t u buttons to adjust the lens position to shift the projected area. 62 English USING THE PROJECTOR Note: BX-CTA17 floating ring For better optical performance, manually adjust the floating ring before adjusting Zoom & Focus. Floating ring's label scale shows the projection distance. The projection distance is from the projector lens to the screen. For example, if the distance between the screen and the projector lens is 1.4 m, adjust the floating ring scale to "1.40" for better performance. label sticker 150.75±2 (Far: 148.75 Near: 152.75) 83.85 Flange back Ø 146 Floating rings label sticker Fixed ring 23.5 19.5 Floating ring Lens Memory This projector can save up to five lens settings, which records the lens position. To record correct data, please perform lens calibration at first time processing lens memory. Save Memory: Select a record from 1 to 5 to save the current lens settings. Apply Memory: Select a record from 1 to 5 to apply the lens settings. Clear Memory: Clear the saved lens records. Note: Must Save Memory before Apply Memory, otherwise the function of apply memory will gray out or disable. Performing a lens calibration will clear the saved lens records. BX-CTA16 setup requires a special support kit. For more information, please refer to the BX-CTA16 user manual. Lens Calibration Calibrate the lens position to return it to the center. To prevent damage to the projector and the lens, always perform lens calibration before replacing the lens. Lens Lock Lock the lens to prevent the lens motors from moving, which disables all lens functions. Reset Reset the lens settings to factory default values. English 63 USING THE PROJECTOR Schedule Schedule the projector functions to operate automatically at the set time. Schedule Date and Time Schedule Mode View Today 2019/11/06 14:00 On Monday Monday On Tuesday Off Wednesday Off Thursday Off Friday Off Saturday Off Sunday Off Reset Schedule Enter Enter Select Exit Return Date and Time Before setting a schedule, setup the date and time settings. Refer to "Date and Time" on page 66. Schedule Mode Enable or disable the schedule function. If the projector is controlled via external devices or software, the Schedule Mode displays AP Mode, and the projector's schedule functions are grayed out. View Today View the event list scheduled for today. Note: After the schedule is set up, make sure to save all the settings. Monday to Sunday Set up the schedule for days of a week. On the Schedule menu page, select a day and configure the schedule settings. Monday Schedule Enable 01 08:00 02 08:01 03 08:01 04 - - : - 05 - - : - 06 - - : - 07 - - : - 08 - - : - More Events Copy Events To Reset the Day Power On HDMI 1 Normal Mode --------------------------------------------------- Event 01 Time Event Reset Power On ECO Active Communication 08:00 Power Settings 64 English Enter Enter Select Exit Return Enter Enter Select Exit Return Schedule Enable: Enable or disable the schedule function for the selected day. USING THE PROJECTOR Event 01-16: Select an event record number, and set up the schedule details. ± Time: Set the time for the event. ± Function: Select the function. The available functions are Power Settings, Input Source, Light Source Mode, and Shutter Note: If the Power Setting is set to Eco or Active, then the projector cannot boot up again. ± Event: Select a function for the event, which operates automatically at the set time. ± Reset: Reset the event settings. Event List 01 08:00 02 08:01 03 08:01 04 - - : - 05 - - : - 06 - - : - 07 - - : - 08 - - : - 09 - - : - 10 - - : - - Page 1/2 Power On HDMI 1 Normal Mode ----------------------------------------------------------------------- Event List 11 - - : - 12 - - : - 13 - - : - 14 - - : - 15 - - : - 16 - - : - - Page 2/2 ------------------------------------------------------------- Enter Enter Select Change Exit Return Enter Enter Select Change Exit Return Copy Events To: Copy the events setup for the day to another day. Monday Schedule Enable 01 08:00 02 08:01 03 08:01 04 - - : - 05 - - : - 06 - - : - 07 - - : - 08 - - : - More Events Copy Events To Reset the Day Power On HDMI 1 Normal Mode --------------------------------------------------- Tuesday Schedule Enable 01 08:00 02 08:01 03 08:01 04 - - : - 05 - - : - 06 - - : - 07 - - : - 08 - - : - More Events Copy Events To Reset the Day Power On HDMI 1 Normal Mode --------------------------------------------------- Enter Enter Select Exit Return Enter Enter Select Reset the Day: Reset the schedule settings for the day. Reset Schedule Reset all of the schedule settings. Exit Return English 65 USING THE PROJECTOR Date and Time Set up the projector's date and time. Clock Mode Set the clock mode to NTP Server or Manual. Note: To use NTP Server, make sure the projector is connected to the Internet. Date Set a date for the projector. The date format is in Year/Month/Date. Time Set the time for the projector. Daylight Saving Time Enable or disable the daylight savings function. NTP Server Select a NTP Server for the network clock mode. Time Zone Set a time zone for the network clock mode. Update Interval Set the date and time update interval. Apply Apply date and time modifications. 66 English USING THE PROJECTOR Power Settings Configure the projector's power settings. Power Mode (Standby) Setup the projector's standby mode. Eco: Minimum power consumption (< 0.5 Watt) which does not allow network control. Active: Low power consumption (< 2 Watt) which allows the LAN module to enter sleep mode and supports to be woken by Wake on LAN (WoL). When the LAN module is woken by WoL, the projector is ready to receive commands over the network. Communication: More power consumption that allows controlling the projector over the network. Signal Power On Turn on this function to have the projector automatically turning on when connected to HDMI input sources. It only applies to the standby projector set to Communication mode. Auto Power Off Set an interval timer for the projector to automatically turn off if no signal is detected within the specified time period. Press the t and u buttons to add or reduce time, 1 minute for each press. Sleep Timer Set an interval timer for the projector to automatically turn off after operating for the specified amount of time. 12V Trigger When enabled, the projector screen is automatically raised or lowered when the projector is turned on or off. This function only works when the projector is connected to an electrical projector screen. Note: 3.5mm mini jack that outputs 12V 500mA (max.) for relay system control. On: Choose "On" to enable the trigger. Off: Choose "Off" to disable the trigger. Reset Reset the power settings to factory default values. 12V Trigger Output Reserved GND Light Source Settings Set up the light source to control the projector brightness. Light Source Mode Select a light source mode depending on the installation requirements. The available options are Normal, Eco Mode, and Custom Power. Custom Brightness When the Light Source Mode is set to Custom Mode, set up the custom brightness level. Set up the Constant Brightness to maintain the image brightness at a specified level. A special algorithm is designed to compensate for the natural decay of brightness so that the image can be maintained at a fixed brightness level. Brightness Level: Adjust the brightness level from 30% to 100%. Constant Brightness: Enable to maintain the image brightness at the set brightness level. A special algorithm is designed to compensate for the natural decay of brightness so that the image can be maintained at a fixed brightness level. English 67 USING THE PROJECTOR Shutter Set up the shutter behavior. Fade-In This function allows the fading-in effect when turning off the shutter. The length of the fading effect can be adjusted from 0s to 5s. Fade-Out This function allows the fading-out effect when turning on the shutter. The length of the fading effect can be adjusted from 0s to 5s. Startup Select the shutter behavior when turning on the projector. Shutter Off: Projector projects images normally after being powered on. Shutter On: Projector automatically turns on shutter after being powered on. Security Set up security verification to protect the projector. Security Select On to protect the projector with a password. If the user enters incorrect password three times, a message will pop up warning that the projector shuts down in 10 seconds. Security Timer Specify the length of time the projector can be used without the password. Once the timer counts to 0, the user must enter a password to use the projector. The timer restarts every time the projector is turned on. Change Password Change the projector password. Note: In the last minute before reaching a specified timer, including Auto Power Off, Sleep Timer, and Security Timer, an on-screen message will pop up warning that the projector shuts down in 60 seconds. Press any button on the remote control or projector keypad to reset the timer and the projector remains on. On Screen Display Set up the on screen display menus. Menu Location Select the menu location from Top Left, Top Right, Center, Bottom Left, and Bottom Right. Menu Transparency Set the menu transparency level. Menu Timer Set the length of time the menu displays on the screen. Information Hide Enable or disable the corner information messages, such as input source, IP address, and so on. Background Set a background color to display when no input signal is detected. The available options are Blue, Black, White, and Logo. 68 English USING THE PROJECTOR Logo Setup Set up the logo for the startup screen. Change Logo Change the logo for the startup screen. Apart from the Default logo, user can select from Neutral, User Logo, and Captured Logo. Default: The projector default logo. Neutral: The logo is not displayed on the startup screen. User Logo: User customized logo. Captured Logo: The logo saved via the Logo Capture function. Note: The supported logo format is PNG and size is 1920 x 1200 pixels. Logo Capture Capture part of the projected image and save it as a customized logo. Delete Logo Delete the saved customized logo, including the Captured Logo and User Logo. Backlight Set up the projector backlight options. Keypad Enable or disable the keypad backlight. Power Key Enable or disable the backlight for the power key. High Altitude Select On to increase the fan speed. To ensure the image quality and prevent damage to the projector, enable High Altitude mode in high temperature, high humidity, or high altitude environment. User Data User can save the projector settings as user data and reload the settings later. Save all settings: Save all of the projector settings as user data. User can save up to 5 records. Load all settings: Load the previously saved user data. System Update (FOTA) Update the system automatically or manually. Auto: System checks for new updates automatically every time it is connected to the Internet. Auto Download: System will download the firmware upgrade file in the background and starts the upgrade process when you power off the projector. When the upgrade is done, the projector will power off. Update: Manually update the system firmware. Reset Reset the settings to factory default values. Reset OSD: Reset OSD settings to default values. Reset to Default: Reset all projector settings to default values. Reset Selective: Reset the settings of one of the main menus. User can choose from Image, Display, Advanced, Input, Communication, and Setup. English 69 USING THE PROJECTOR Communication menu Communication menu is used to configure the settings that allow the projector to communicate with other projectors or control devices. Submenus Projector ID Remote Setup Network Setup Email Notification Control Baud Rate Supplemental information Using the web control panel Using RS232 command by Telnet Projector ID Assign an ID code for the projector from 00 to 99. Use this code as the projector ID when controlling the projector by RS232, HDBaseT, Telnet or other control methods. Remote Setup Configure the settings of the Infra-Red (IR) remote control. Remote Code Press and hold the remote control ID key. When all the key lights turn on, press the number key 00-99 to assign a number. When all key lights flash rapidly twice, the remote control code has been changed. At this time, release the remote control ID key. Quick Switch Code The IR receiving function of the projector can be temporarily deactivated by hot key(0~9) to avoid the IR interference between projectors. The remote ID needs to be set to All. Note: When hotkey is on, the default functions are inactive temporarily. IR Function Set the remote receiver for the projector to control the communication between the projector and the IR remote. Front: Enable or disable the front remote receiver. Top: Enable or disable the top remote receiver. HDBaseT: Select On to set the HDBaseT terminal as the remote receiver. User 1 / User 2 Assign a function to the User 1 and User 2 buttons on the remote control. It allows you to use the function easily without going through the OSD menus. The available functions are Freeze Screen, Blank Screen, PIP/ PBP, Aspect Ratio, Information Hide, Network Setup, Projector ID, Color Matching, and Reset Selective. 70 English USING THE PROJECTOR Network Setup Configure the projector's network settings. LAN Interface To avoid clash, specify the LAN interface to RJ-45 or HDBaseT. MAC Address Display the MAC address. (Read only) Network Status Display the network connection status. (Read only) DHCP Turn on DHCP to automatically acquire IP address, subnet mask, gateway, and DNS. IP Address Assign the projector's IP address. Subnet Mask Assign the projector's subnet mask. Gateway Assign the projector's gateway. DNS Assign the projector's DNS. Apply Apply the wired network settings. Network Reset Reset the network settings to default factory values. Email Notification Set up email notifications for some events, which allows them to be received as early alerts via emails. Control This projector can be controlled remotely by a computer or other external devices through wireless or wired network connection. It allows the user to control one or more projectors from a remote control center, such as powering the projector on or off, and adjusting the image brightness or contrast. Use the Control submenu to select a control device for the projector. Crestron Control the projector with Crestron controller and related software. (Port: 41794) For more information, please visit http://www.crestron.com. Crestron Setup: Setup the Crestron IP Address, IPID, and Port. Then select Crestron Setup Apply to save the modifications. PJ Link Control the projector with PJLink v2.0 commands. (Port: 4352) For more information, please visit http://pjlink.jbmia.or.jp/english. PJ Link Service: Setup the address for the PJ Link service and the related settings. Then select PJ Link Setup Apply to save the modifications. Extron Control the projector with Extron devices. (Port: 2023) For more information, please visit http://www.extron.com. English 71 USING THE PROJECTOR AMX Control the projector with AMX devices. (Port: 9131) For more information, please visit http://www.amx.com. Telnet Control the projector using RS232 commands though Telnet connection. (Port: 23) For more information, refer to "Using RS232 command by Telnet" on page 76. HTTP Control the projector with web browser. (Port: 80) For more information, refer to "Using the web control panel" on page 73. Optoma Management Suite (OMS) Control the projector with OMS. For more information, please visit https://www.optoma.com. Reset Reset the control functions to default factory values. Projector (Ethernet) Note: Crestron is a registered trademark of Crestron Electronics, Inc. of the United States. Extron is a registered trademark of Extron Electronics, Inc. of the United States. AMX is a registered trademark of AMX LLC of the United States. PJLink applied for trademark and logo registration in Japan, the United States of America, and other countries by JBMIA. For more information about the various types of external devices which can be connected to the LAN / RJ45 port and remotely control the projector, as well as the supported commands for these external devices, please contact the Support-Service directly. Baud Rate Set the baud rate for Serial Port In and Serial Port Out. The available options are 1200, 2400, 4800, 9600, 19200, 38400, 57600, and 115200. Reset Reset all network settings to default factory values. 72 English USING THE PROJECTOR Using the web control panel The Web control panel allows the user to configure various projector settings using a web browser from any personal computer or mobile devices. System Requirements To use the web control panel, make sure your devices and software meet the minimum system requirements. RJ45 cable (CAT-5e) or wireless dongle PC, laptop, mobile phone, or tablet installed with a web browser Compatible web browsers: ± Microsoft Edge 40 or higher version ± Firefox 57 or higher version ± Chrome 63 or higher version Overview of the web control panel Configure the projector settings using web browser. Menu Settings Menu HOME IMAGE DISPLAY INPUT SETTINGS DEVICE SETUP COMMUNICATION INFORMATION Description View the projector information and firmware version details. To configure image settings. To configure the settings to properly project images according to your installation circumstances. To configure the projector input settings. To configure the system settings for the projector. Communication menu is used to configure the settings that allow the projector to communicate with other projectors or control devices. View the projector information about its status and settings. The projector information is read only. English 73 USING THE PROJECTOR Accessing the web control panel When network is available, connect the projector and the computer to the same network. Use the projector address as the web URL to open the web control panel in a browser. 1. Check the projector address using the OSD menu. On a wired network, select Network > LAN > IP Address. Note: Make sure DHCP is enabled. On a wireless network, select Network > WLAN > Gateway. 2. Open a web browser and type the projector address in the address bar. 3. The web page redirects to the web control panel. 4. In the Username field, type the username: admin(default). In the Password field, type the password.: Device serial number(default). You can obtain the serial number from one of the following methods: a. The label on the projector as shown below: A , : , , , , , , / / DLP Projector Regulatory No. : DAZUGGZZ / / Input :AC 100-120V~, 50/60 Hz, 9A / / Model name : Serial No.: N7KB212AAAAVA0001 R3E815 / MFG:2022.02 MADE IN TAIWAN This device complies with part 15 of the FCC rules.Operation is subject to the following two conditions: (1)this device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-003(A)/NMB-003(A) UK Rep.: Optoma Europe Ltd 1 Bourne End Mills Hemel Hempstead, Herts, UK EU Rep.: Optoma Benelux BV Europalaan 770 D, 1363 BM Almere, The Netherlands Note: Label image is only for reference. b. From the OSD menu (Go to Information Device Serial Number): Information Device System Status Communication Signal Backup Input Firmware Version Regulatory Serial Number Projection Hours Device Select Exit Enter Note: It is needed to change the username and password once you have logged in. It is also advised to use a strong password. When network is not available, refer to "Directly connect the projector to a computer" on page 75. 74 English USING THE PROJECTOR Directly connect the projector to a computer When network is not available, connect the projector to the computer directly using a RJ-45 cable, and configure the network settings manually. RJ-45 Cable 1. Assign IP address to the projector From the OSD menu, select Network > LAN. Turn off DHCP, and manually set the projector's IP Address, Subnet Mask, and Gateway. Press Enter to confirm the settings. 2. Assign IP address to the computer Set the Default Gateway and Subnet Mask of the computer to match the projector. Set the IP address of the computer to match the first three numbers of the projector. For example, if the projector IP address is 192.168.000.100, set the computer IP address to 192.168.000.xxx, where xxx is not 100. 3. Open a web browser and type the projector address in the address bar. 4. The web page redirects to the web control panel. English 75 USING THE PROJECTOR Using RS232 command by Telnet This projector supports using RS232 commands through Telnet connection. 1. Set up a direct connection between the projector and computer. Refer to Directly connect the projector to a computer on page 75. 2. Disable the firewall on the computer. 3. Open the command dialogue on the computer. For Windows 7 operating system, select Start > All Programs > Accessories > Command Prompt. 4. Input the command "telnet ttt.xxx.yyy.zzz 23". Replace "ttt.xxx.yyy.zzz" with the projector IP address. 5. Press Enter on the computer keyboard. Specification for RS232 by Telnet Telnet: TCP Telnet port: 23 (contact service team for more details) Telnet utility: Windows "TELNET.exe" (console mode). Disconnection for RS232-by-Telnet control normally: Close Below are the limitations for using Windows Telnet utility directly after TELNET connection is ready: ± There is less than 50 bytes for successive network payload for Telnet-Control application. ± There is less than 26 bytes for one complete RS232 command for Telnet-Control. ± Minimum delay for next RS232 command must be more than 200 (ms).Information menu. Info menu View the projector information about its status and settings. The projector information is read only. Submenus Device System Status Communication Signal Backup Input Firmware Version 76 English ADDITIONAL INFORMATION Compatible resolutions Timing table Signal Type Signal Format VGA SVGA XGA SXGA PC WXGA WXGA SXGA WXGA SXGA+ WXGA+ WXGA++ UXGA Resolution 640 x 350 640 x 400 640 x 480 720 x 400 800 x 600 832 x 624 848 x 480 1024 x 768 1152 x 864 1152 x 870 1280 x 768 1280 x 800 1280x960 1280 x 1024 1360 x 765 1360 x 768 1366 x 768 1400 x 1050 1440 x 900 1600 x 900 1600 x 1200 Aspect Ratio V Sync (Hz) 85 16:10 85 60 1.33 72 4:3 75 85 70 1.8 9:5 85 60 72 1.33 4:3 75 85 120 75 1.33 4:3 60 60 70 1.33 4:3 75 85 120 1.33 75 4:3 1.32 75 60 1.67 5:3 75 85 60 1.6 16:10 75 85 60 1.33 4:3 85 60 1.25 5:4 75 85 60 1.78 16:9 60 60 1.33 4:3 60 60 1.6 16:10 75 85 1.78 16:9 60 50 1.33 4:3 60 8 bit V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V HDMI 1/HDMI 2 RGB YCbCr 4:4:4 YCbCr 4:2:2 10 bit 12 bit 8 bit 10 bit 12 bit 8 bit V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V NA NA V NA NA NA V V V V V V V V V V V NA V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V English 77 ADDITIONAL INFORMATION Signal Type Signal Format WSXGA+ PC WUXGA RB 2K SDTV (480i) SDTV (480i) SDTV (576i) EDTV (480p) EDTV (480p) EDTV (576p) HDTV (1080i) TV HDTV (720p) HDTV (1080p) SD-SDI SDTV (480i) SDTV (576i) HDTV (720p) HDTV (1080i) HD-SDI HDTV (1080p) 3GA-SDI HDTV (1080sF) HDTV (1080p) Resolution 1680 x 1050 1920 x 1200RB 2560 x 1440RB 720 x 480 720 x 480 720 x 576 720 x 480 720 x 480 720 x 576 1920 x 1080 1280 x 720 1920 x 1080 720 x 480 720 x 576 1280 x 720 1920 x 1080 1920 x 1080 1920 x 1080 1920 x 1080 Aspect Ratio V Sync (Hz) 1.6 16:10 1.6 16:10 1.78 16:9 1.5 3:2 1.5 3:2 1.25 5:4 1.5 3:2 1.5 3:2 1.25 5:4 1.78 16:9 1.78 16:9 1.78 16:9 1.5 3:2 1.25 5:4 1.78 16:9 1.78 16:9 1.78 16:9 1.78 16:9 1.78 16:9 60 50 60 60 59.94 60 50 59.94 60 50 50 59.94 60 50 59.94 60 120 23.98 24 25 29.97 30 50 59.94 60 59.94 50 50 59.94 60 50 59.94 60 23.98 24 25 29.97 30 25 29.97 30 50 59.94 60 8 bit V V V V V V V V V V V V V V V V V V V V V V V V V NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA HDMI 1/HDMI 2 RGB YCbCr 4:4:4 YCbCr 4:2:2 10 bit 12 bit 8 bit 10 bit 12 bit 8 bit V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA 78 English ADDITIONAL INFORMATION Signal Type 3GB-SDI Mandatory 3D Mandatory 3D Frame Sequential 3D 4K Signal Format HDTV (1080p) Frame Packing (1080p) Frame Packing (720p) Side by Side (1080i) Side by Side (1080p) Top and Bottom (720p) Top and Bottom (1080p) SVGA XGA HDTV HDTV 1080p WUXGA 3840 x 2160 4096 x 2160 SMPTE Resolution 1920x1080 with 352M Payload ID 1920 x 1080 1280 x 720 1920 x 1080 1920 x 1080 1280 x 720 1920 x 1080 800 x 600 1024 x 768 1280 x 720 1280 x 800 1920 x 1080 1920 x 1200 3840 x 2160 4096 x 2160 Aspect Ratio V Sync (Hz) 1.78 16:9 1.78 16:9 1.78 16:9 1.78 16:9 1.78 16:9 1.78 16:9 1.78 16:9 1.33 4:3 1.33 4:3 1.78 16:9 1.78 16:9 1.78 16:9 1.6 16:10 1.78 16:9 1.9 N/A 50 59.94 60 23.98 24 50 59.94 60 50 59.94 60 24 50 59.9 60 50 59.94 60 23.98 24 59.9 60 120 120 120 120 120 60 60 24 25 30 50 60 24 25 30 50 60 8 bit NA NA NA V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V RGB HDMI 1/HDMI 2 YCbCr 4:4:4 YCbCr 4:2:2 10 bit NA NA NA V 12 bit NA NA NA V 8 bit NA NA NA V 10 bit NA NA NA V 12 bit NA NA NA V 8 bit NA NA NA V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V X V V V V V V V V V V V V V V V V V V V V V V V V NA NA V NA NA V NA NA V NA NA V V V V V V V V V V V V V V V V V V V NA NA V NA NA V NA NA V NA NA V Note: · "V" means supported and "NA" means not supported. · "RB" means "reduced blanking". English 79 ADDITIONAL INFORMATION Signal Type PC Signal Format VGA SVGA XGA SXGA WXGA WXGA SXGA WXGA SXGA+ WXGA+ WXGA++ UXGA WSXGA+ WUXGA RB Resolution 640 x 350 640 x 400 640 x 480 720 x 400 800 x 600 832 x 624 848 x 480 1024 x 768 1152 x 864 1152 x 870 1280 x 768 1280 x 800 1280x960 1280 x 1024 1360 x 765 1360 x 768 1366 x 768 1400 x 1050 1440 x 900 1600 x 900 1600 x 1200 1680 x 1050 1920 x 1200RB Aspect V Sync Ratio (Hz) 8 bit 85 V 16:10 85 V 60 V 1.33 72 V 4:3 75 V 85 V 70 V 1.8 9:5 85 V 60 V 72 NA 1.33 4:3 75 NA 85 V 120 NA 75 V 1.33 4:3 60 V 60 V 70 NA 1.33 4:3 75 NA 85 V 120 NA 1.33 75 V 4:3 1.32 75 V 60 NA 1.67 5:3 75 V 85 V 60 NA 1.6 16:10 75 V 85 V 60 V 1.33 4:3 85 V 60 V 1.25 5:4 75 V 85 V 60 V 1.78 16:9 60 V 60 V 1.33 4:3 60 V 60 V 1.6 16:10 75 V 85 V 1.78 16:9 60 V 50 V 1.33 4:3 60 V 1.6 16:10 60 V 50 V 1.6 16:10 60 V RGB 10 bit V V V V V V V V V NA NA V NA V V V NA NA V NA V V NA V V NA V V V V V V V NA V V V V V V V V V V V V DVI YCbCr 4:4:4 12 bit 8 bit 10 bit 12 bit V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V NA NA NA NA NA NA NA NA V NA NA NA NA NA NA NA V NA NA NA V V V V V V V V NA NA NA NA NA V V V V V V V NA NA NA NA V V V V V V V V NA V NA NA V V V V V V V V NA V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V NA V NA NA V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V YCbCr 4:2:2 8 bit V V V V V V V V V V V V NA V V V V V V NA V V V V V V V V V V V V V NA V V V V V V V V V V V V 80 English ADDITIONAL INFORMATION Signal Type PC TV SD-SDI HD-SDI 3GA-SDI 3GB-SDI Mandatory 3D Signal Format Resolution 2K SDTV (480i) SDTV (480i) SDTV (576i) EDTV (480p) EDTV (480p) EDTV (576p) 2560 x 1440RB 720 x 480 720 x 480 720 x 576 720 x 480 720 x 480 720 x 576 HDTV (1080i) 1920 x 1080 HDTV (720p) 1280 x 720 HDTV (1080p) 1920 x 1080 SDTV (480i) SDTV (576i) 720 x 480 720 x 576 HDTV (720p) 1280 x 720 HDTV (1080i) 1920 x 1080 HDTV (1080p) 1920 x 1080 HDTV (1080sF) 1920 x 1080 HDTV (1080p) 1920 x 1080 HDTV (1080p) Frame Packing (1080p) 1920x1080 with 352M Payload ID 1920 x 1080 Aspect Ratio 1.78 16:9 1.5 3:2 1.5 3:2 1.25 5:4 1.5 3:2 1.5 3:2 1.25 5:4 1.78 16:9 1.78 16:9 1.78 16:9 1.5 3:2 1.25 5:4 1.78 16:9 1.78 16:9 1.78 16:9 1.78 16:9 1.78 16:9 1.78 16:9 1.78 16:9 V Sync (Hz) 60 59.94 60 50 59.94 60 50 50 59.94 60 50 59.94 60 120 23.98 24 25 29.97 30 50 59.94 60 59.94 50 50 59.94 60 50 59.94 60 23.98 24 25 29.97 30 25 29.97 30 50 59.94 60 50 59.94 60 23.98 8 bit NA V V V V V V V V V V V V NA V V V V V V V V NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA RGB 10 bit NA V V V V V V V V V V V V NA V V V V V V V V NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA 12 bit NA V V V V V V V V V V V V NA V V V V V V V V NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA DVI YCbCr 4:4:4 8 bit 10 bit 12 bit NA NA NA V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V NA NA NA V V V V V V V V V V V V V V V V V V V V V V V V NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA YCbCr 4:2:2 8 bit NA V V V V V V V V V V V V NA V V V V V V V V NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA 24 NA NA NA NA NA NA NA English 81 ADDITIONAL INFORMATION Signal Type Signal Format Frame Packing (720p) Side by Side (1080i) Mandatory 3D Side by Side (1080p) Top and Bottom (720p) Frame Sequential 3D Top and Bottom (1080p) SVGA XGA HDTV HDTV 1080p WUXGA 3840 x 2160 4K 4096 x 2160 SMPTE Resolution 1280 x 720 1920 x 1080 1920 x 1080 1280 x 720 1920 x 1080 800 x 600 1024 x 768 1280 x 720 1280 x 800 1920 x 1080 1920 x 1200 3840 x 2160 4096 x 2160 Aspect Ratio 1.78 16:9 1.78 16:9 1.78 16:9 1.78 16:9 1.78 16:9 1.33 4:3 1.33 4:3 1.78 16:9 1.78 16:9 1.78 16:9 1.6 16:10 1.78 16:9 1.9 N/A V Sync (Hz) 50 59.94 60 50 59.94 60 24 50 59.9 60 50 59.94 60 23.98 24 59.9 60 120 120 120 120 120 60 60 24 25 30 50 60 24 25 30 50 60 8 bit NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA V V V V V V V NA NA NA NA NA NA NA NA NA NA RGB 10 bit NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA V V V V V V V NA NA NA NA NA NA NA NA NA NA 12 bit NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA V V V V V V V NA NA NA NA NA NA NA NA NA NA DVI YCbCr 4:4:4 8 bit 10 bit 12 bit NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA V V V V V V V V V V V V V V V V V V V V V NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA YCbCr 4:2:2 8 bit NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA V V V V V V V NA NA NA NA NA NA NA NA NA NA Note: · "V" means supported and "NA" means not supported. · "RB" means "reduced blanking". 82 English ADDITIONAL INFORMATION Signal Type Signal Format Resolution 640 x 350 640 x 400 VGA 640 x 480 720 x 400 SVGA 800 x 600 832 x 624 848 x 480 XGA 1024 x 768 SXGA 1152 x 864 1152 x 870 PC WXGA 1280 x 768 WXGA 1280 x 800 SXGA WXGA SXGA+ WXGA+ WXGA++ UXGA WSXGA+ WUXGA RB 2K 1280x960 1280 x 1024 1360 x 765 1360 x 768 1366 x 768 1400 x 1050 1440 x 900 1600 x 900 1600 x 1200 1680 x 1050 1920 x 1200RB 2560 x 1440RB Aspect Ratio 16:10 1.33 4:3 1.8 9:5 1.33 4:3 1.33 4:3 1.33 4:3 1.33 4:3 1.32 1.67 5:3 1.6 16:10 1.33 4:3 1.25 5:4 1.78 16:9 1.33 4:3 1.6 16:10 1.78 16:9 1.33 4:3 1.6 16:10 1.6 16:10 1.78 16:9 V Sync (Hz) 85 85 60 72 75 85 70 85 60 72 75 85 120 75 60 60 70 75 85 120 75 75 60 75 85 60 75 85 60 85 60 75 85 60 60 60 60 60 75 85 60 50 60 60 50 60 60 3G-SDI YCbCr 4:2:2 10 bit NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA English 83 ADDITIONAL INFORMATION Signal Type Signal Format Resolution SDTV (480i) SDTV (480i) SDTV (576i) EDTV (480p) EDTV (480p) EDTV (576p) 720 x 480 720 x 480 720 x 576 720 x 480 720 x 480 720 x 576 HDTV (1080i) 1920 x 1080 TV HDTV (720p) 1280 x 720 Aspect Ratio 1.5 3:2 1.5 3:2 1.25 5:4 1.5 3:2 1.5 3:2 1.25 5:4 1.78 16:9 1.78 16:9 HDTV (1080p) 1920 x 1080 1.78 16:9 SDTV (480i) 720 x 480 1.5 3:2 SD-SDI SDTV (576i) 720 x 576 1.25 5:4 HDTV (720p) 1280 x 720 1.78 16:9 HDTV (1080i) 1920 x 1080 1.78 16:9 HD-SDI HDTV (1080p) 1920 x 1080 1.78 16:9 HDTV (1080sF) 1920 x 1080 1.78 16:9 3GA-SDI HDTV (1080p) 1920 x 1080 1.78 16:9 3GB-SDI HDTV (1080p) 1920x1080 with 352M Payload ID 1.78 16:9 Mandatory 3D Frame Packing (1080p) 1920 x 1080 1.78 16:9 V Sync (Hz) 59.94 60 50 59.94 60 50 50 59.94 60 50 59.94 60 120 23.98 24 25 29.97 30 50 59.94 60 59.94 50 50 59.94 60 50 59.94 60 23.98 24 25 29.97 30 25 29.97 30 50 59.94 60 50 59.94 60 23.98 24 3G-SDI YCbCr 4:2:2 10 bit NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA V V V V V V V V V V V V V V V V V V V V V V NA NA 84 English ADDITIONAL INFORMATION Signal Type Signal Format Resolution Frame Packing (720p) 1280 x 720 Side by Side (1080i) 1920 x 1080 Mandatory 3D Side by Side (1080p) 1920 x 1080 Top and Bottom (720p) 1280 x 720 Top and Bottom (1080p) 1920 x 1080 Frame Sequential 3D SVGA XGA HDTV HDTV 1080p 800 x 600 1024 x 768 1280 x 720 1280 x 800 1920 x 1080 WUXGA 1920 x 1200 Aspect Ratio 1.78 16:9 1.78 16:9 1.78 16:9 1.78 16:9 1.78 16:9 1.33 4:3 1.33 4:3 1.78 16:9 1.78 16:9 1.78 16:9 1.6 16:10 3840 x 2160 3840 x 2160 1.78 16:9 4K 4096 x 2160 SMPTE 4096 x 2160 1.9 N/A Note: · "V" means supported and "NA" means not supported. · "RB" means "reduced blanking". V Sync (Hz) 50 59.94 60 50 59.94 60 24 50 59.9 60 50 59.94 60 23.98 24 59.9 60 120 120 120 120 120 60 50 120 60 24 25 30 50 60 24 25 30 50 60 3G-SDI YCbCr 4:2:2 10 bit NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA English 85 ADDITIONAL INFORMATION Signal Type PC Signal Format VGA SVGA XGA SXGA WXGA WXGA SXGA WXGA SXGA+ WXGA+ WXGA++ UXGA WSXGA+ WUXGA RB Resolution Aspect Ratio 640 x 350 640 x 400 640 x 480 16:10 1.33 4:3 720 x 400 1.8 9:5 800 x 600 1.33 4:3 832 x 624 848 x 480 1.33 4:3 1024 x 768 1.33 4:3 1152 x 864 1152 x 870 1.33 4:3 1.32 1280 x 768 1.67 5:3 1280 x 800 1.6 16:10 1280x960 1.33 4:3 1280 x 1024 1.25 5:4 1360 x 765 1360 x 768 1366 x 768 1400 x 1050 1.78 16:9 1.33 4:3 1440 x 900 1.6 16:10 1600 x 900 1.78 16:9 1600 x 1200 1.33 4:3 1680 x 1050 1.6 16:10 1920 x 1200RB 1.6 16:10 V Sync (Hz) 85 85 60 72 75 85 70 85 60 72 75 85 120 75 60 60 70 75 85 120 75 75 60 75 85 60 75 85 60 85 60 75 85 60 60 60 60 60 75 85 60 50 60 60 50 60 8 bit V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V RGB 10 bit V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V NA V V V V V V V V V V V V HDBaseT YCbCr 4:4:4 YCbCr 4:2:2 12 bit 8 bit 10 bit 12 bit 8 bit V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V NA V NA V NA NA NA V V V V V V V V V NA V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V NA V V V V V V V V V V V V V V NA V 86 English ADDITIONAL INFORMATION Signal Type Signal Format Resolution Aspect Ratio PC 2K 2560 x 1440RB 1.78 16:9 SDTV (480i) 720 x 480 1.5 3:2 SDTV (480i) 720 x 480 1.5 3:2 SDTV (576i) 720 x 576 1.25 5:4 EDTV (480p) 720 x 480 1.5 3:2 EDTV (480p) 720 x 480 1.5 3:2 EDTV (576p) 720 x 576 1.25 5:4 HDTV (1080i) 1920 x 1080 1.78 16:9 TV HDTV (720p) 1280 x 720 1.78 16:9 HDTV (1080p) 1920 x 1080 1.78 16:9 SD-SDI SDTV (480i) SDTV (576i) 720 x 480 720 x 576 1.5 3:2 1.25 5:4 HDTV (720p) 1280 x 720 1.78 16:9 HDTV (1080i) 1920 x 1080 1.78 16:9 HD-SDI HDTV (1080p) 1920 x 1080 1.78 16:9 HDTV (1080sF) 1920 x 1080 1.78 16:9 3GA-SDI HDTV (1080p) 1920 x 1080 1.78 16:9 3GB-SDI HDTV (1080p) Mandatory 3D Frame Packing (1080p) 1920x1080 with 352M Payload ID 1920 x 1080 1.78 16:9 1.78 16:9 V Sync (Hz) 60 59.94 60 50 59.94 60 50 50 59.94 60 50 59.94 60 120 23.98 24 25 29.97 30 50 59.94 60 59.94 50 50 59.94 60 50 59.94 60 23.98 24 25 29.97 30 25 29.97 30 50 59.94 60 50 59.94 60 23.98 24 8 bit V V V V V V V V V V V V V V V V V V V V V V NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA V V RGB 10 bit NA V V V V V V V V V V V V V V V V V V V V V NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA V V HDBaseT YCbCr 4:4:4 YCbCr 4:2:2 12 bit 8 bit 10 bit 12 bit 8 bit NA V NA NA V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA V V V V V V V V V V English 87 ADDITIONAL INFORMATION Signal Type Mandatory 3D Frame Sequential 3D 4K Signal Format Frame Packing (720p) Side by Side (1080i) Side by Side (1080p) Top and Bottom (720p) Top and Bottom (1080p) SVGA XGA HDTV HDTV 1080p WUXGA 3840 x 2160 4096 x 2160 SMPTE Resolution 1280 x 720 1920 x 1080 1920 x 1080 1280 x 720 1920 x 1080 800 x 600 1024 x 768 1280 x 720 1280 x 800 1920 x 1080 1920 x 1200 3840 x 2160 4096 x 2160 Aspect Ratio 1.78 16:9 1.78 16:9 1.78 16:9 1.78 16:9 1.78 16:9 1.33 4:3 1.33 4:3 1.78 16:9 1.78 16:9 1.78 16:9 1.6 16:10 1.78 16:9 1.9 N/A V Sync (Hz) 50 59.94 60 50 59.94 60 24 50 59.9 60 50 59.94 60 23.98 24 59.9 60 120 120 120 120 120 60 60 24 25 30 50 60 24 25 30 50 60 8 bit V V V V V V V V V V V V V V V V V V V V V V V V V V V NA NA NA NA NA NA NA RGB 10 bit V V V V V V V V V V V V V V V V V V V V V V V V V V V NA NA NA NA NA NA NA HDBaseT YCbCr 4:4:4 YCbCr 4:2:2 12 bit 8 bit 10 bit 12 bit 8 bit V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA Note: · "V" means supported and "NA" means not supported. · "RB" means "reduced blanking". 88 English ADDITIONAL INFORMATION EDID table Established Timing: 720 x 400 @70Hz 720 x 400 @88Hz 640 x 480 @60Hz 640 x 480 @67Hz 640 x 480 @72Hz 640 x 480 @75Hz 800 x 600 @56Hz 800 x 600 @60Hz 800 x 600 @72Hz 800 x 600 @75Hz 832 x 624 @75Hz 1024 x 768 @60Hz 1024 x 768 @70Hz 1024 x 768 @75Hz 1280 x 1024 @75Hz 1152 x 870 @75Hz Established Timing: 720 x 400 @70Hz 720 x 400 @88Hz 640 x 480 @60Hz 640 x 480 @67Hz 640 x 480 @72Hz 640 x 480 @75Hz 800 x 600 @56Hz 800 x 600 @60Hz 800 x 600 @72Hz 800 x 600 @75Hz 832 x 624 @75Hz 1024 x 768 @60Hz 1024 x 768 @70Hz 1024 x 768 @75Hz 1280 x 1024 @75Hz 1152 x 870 @75Hz DVI Standard Timing: 1024 x 768 @120Hz 1280 x 800 @75Hz 1280 x 1024 @60Hz 1360 x 765 @60Hz 800 x 600 @120Hz 1400 x 1050 @60Hz 1600 x 1200 @60Hz 1680 x 1050 @60Hz HDMI 1.4 Standard Timing: 1024 x 768 @120Hz 1280 x 800 @75Hz 1280 x 1024 @60Hz 1360 x 765 @60Hz 800 x 600 @120Hz 1400 x 1050 @60Hz 1600 x 1200 @60Hz 1680 x 1050 @60Hz Detail Timing: 1920 x 1200 @59Hz 1920 x 1080 @60Hz 640 x 480 @60Hz 720 x 480 @60Hz 1280 x 720 @60Hz 1920 x 1080i @60Hz 720 x 480i @60Hz 720 x 576 @50Hz 1280 x 720 @50Hz 1920 x 1080i @50Hz 720 x 576i @50Hz 1920 x 1080 @50Hz 1920 x 1080 @24Hz 1440 x 480 @60Hz 1920 x 1080 @25Hz Detail Timing: 1920 x 1200 @59Hz 1920 x 1080 @60Hz 640 x 480 @60Hz 720 x 480 @60Hz 1280 x 720 @60Hz 1920 x 1080i @60Hz 720 x 480i @60Hz 720 x 576 @50Hz 1280 x 720 @50Hz 1920 x 1080i @50Hz 720 x 576i @50Hz 1920 x 1080 @50Hz 1920 x 1080 @24Hz 1440 x 480 @60Hz 1920 x 1080 @25Hz 1280 x 720 @120Hz 1920 x 1080 @120Hz 3840 x 2160 @24Hz 3840 x 2160 @25Hz 3840 x 2160 @30Hz 4096 x 2160 @24Hz 4096 x 2160 @25Hz 4096 x 2160 @30Hz English 89 ADDITIONAL INFORMATION Established Timing: 720 x 400 @70Hz 720 x 400 @88Hz 640 x 480 @60Hz 640 x 480 @67Hz 640 x 480 @72Hz 640 x 480 @75Hz 800 x 600 @56Hz 800 x 600 @60Hz 800 x 600 @72Hz 800 x 600 @75Hz 832 x 624 @75Hz 1024 x 768 @60Hz 1024 x 768 @70Hz 1024 x 768 @75Hz 1280 x 1024 @75Hz 1152 x 870 @75Hz HDMI 2.0 Standard Timing: 1024 x 768 @120Hz 1280 x 800 @75Hz 1280 x 1024 @60Hz 1360 x 765 @60Hz 800 x 600 @120Hz 1400 x 1050 @60Hz 1600 x 1200 @60Hz 1680 x 1050 @60Hz Detail Timing: 1920 x 1200 @59Hz 1920 x 1080 @60Hz 640 x 480 @60Hz 720 x 480 @60Hz 1280 x 720 @60Hz 1920 x 1080i @60Hz 720 x 480i @60Hz 720 x 576 @50Hz 1280 x 720 @50Hz 1920 x 1080i @50Hz 720 x 576i @50Hz 1920 x 1080 @50Hz 1920 x 1080 @24Hz 1440 x 480 @60Hz 1920 x 1080 @25Hz 1280 x 720 @120Hz 1920 x 1080 @120Hz 3840 x 2160 @24Hz 3840 x 2160 @25Hz 3840 x 2160 @30Hz 3840 x 2160 @50Hz 3840 x 2160 @60Hz 4096 x 2160 @24Hz 4096 x 2160 @25Hz 4096 x 2160 @30Hz 4096 x 2160 @50Hz 4096 x 2160 @60Hz 90 English ADDITIONAL INFORMATION Image size and projection distance Platform DMD Projection Lens Throw Ratio Spec. (Wide/Tele) Zoom Ratio Throw Distance (m) (min/max) Projection screen size Diagonal Height (inch) (m) 50 0.67 60 0.81 70 0.94 80 1.08 90 1.21 100 1.35 110 1.48 120 1.62 130 1.75 140 1.88 150 2.02 160 2.15 170 2.29 180 2.42 190 2.56 200 2.69 250 3.37 300 4.04 350 4.71 400 5.38 450 6.06 500 6.73 550 7.40 600 8.08 650 8.75 700 9.42 750 10.10 800 10.77 850 11.44 900 12.12 950 12.79 1000 13.46 Width (m) 1.08 1.29 1.51 1.72 1.94 2.15 2.37 2.58 2.80 3.02 3.23 3.45 3.66 3.88 4.09 4.31 5.38 6.46 7.54 8.62 9.69 10.77 11.85 12.92 14.00 15.08 16.15 17.23 18.31 19.39 20.46 21.54 WUXGA (16:10) 0.67" BX-CTA16 BX-CTA17 BX-CTA15 BX-CAA01/ BX-CTA01 BX-CAA06/ BX-CTA06 Ultra Short Throw Short Throw Short Throw Wide Zoom Standard 0.361 (120") 0.65-0.75 0.75-0.95 0.95-1.22 1.22-1.52 NA 1.15x 1.26X 1.28X 1.25X 0.96 ~ 3.01m 0.68 ~ 16.61m 0.79 ~ 20.78m 1.01 ~ 26.68m 1.29 ~ 33.19m Throw distance (m) BX-CAA03/ BX-CTA03 Long Zoom 1.52-2.92 1.9X 1.61 ~ 63.45m BX-CTA13 Ultra-Long Zoom 2.90-5.52 1.9X 3.18 ~ 115.61m - Wide Tele Wide Tele Wide Tele Wide Tele Wide Tele Wide Tele - 0.68 0.79 0.79 1.01 1.01 1.31 1.29 1.62 1.61 3.12 3.18 5.89 - 0.83 0.96 0.96 1.22 1.22 1.57 1.56 1.95 1.94 3.76 3.78 7.05 - 0.97 1.13 1.12 1.43 1.43 1.84 1.82 2.29 2.27 4.39 4.39 8.20 - 1.11 1.29 1.28 1.64 1.63 2.11 2.09 2.62 2.60 5.03 5.00 9.36 - 1.26 1.46 1.45 1.85 1.84 2.38 2.35 2.95 2.94 5.66 5.61 10.51 - 1.40 1.63 1.61 2.05 2.05 2.64 2.62 3.28 3.27 6.30 6.21 11.67 - 1.55 1.79 1.78 2.26 2.26 2.91 2.89 3.62 3.60 6.93 6.82 12.82 0.96 1.69 1.96 1.94 2.47 2.47 3.18 3.15 3.95 3.94 7.57 7.43 13.98 1.04 1.83 2.13 2.10 2.68 2.67 3.44 3.42 4.28 4.27 8.20 8.04 15.13 1.11 1.98 2.29 2.27 2.89 2.88 3.71 3.69 4.61 4.60 8.84 8.65 16.29 1.18 2.12 2.46 2.43 3.09 3.09 3.98 3.95 4.95 4.94 9.47 9.25 17.44 1.26 2.27 2.62 2.60 3.30 3.30 4.24 4.22 5.28 5.27 10.11 9.86 18.60 1.33 2.41 2.79 2.76 3.51 3.51 4.51 4.48 5.61 5.60 10.74 10.47 19.75 1.40 2.55 2.96 2.92 3.72 3.72 4.78 4.75 5.94 5.93 11.38 11.08 20.91 1.48 2.70 3.12 3.09 3.93 3.92 5.05 5.02 6.27 6.27 12.01 11.69 22.06 1.55 2.84 3.29 3.25 4.13 4.13 5.31 5.28 6.61 6.60 12.65 12.29 23.22 1.91 3.56 4.12 4.07 5.17 5.17 6.65 6.61 8.27 8.27 15.82 15.33 28.99 2.28 4.28 4.96 4.89 6.21 6.21 7.98 7.95 9.93 9.93 19.00 18.37 34.77 2.65 5.00 5.79 5.71 7.26 7.25 9.32 9.28 11.59 11.60 22.17 21.41 40.54 3.01 5.72 6.62 6.53 8.30 8.29 10.66 10.61 13.25 13.26 25.35 24.45 46.31 6.45 7.45 7.35 9.34 9.33 11.99 11.94 14.92 14.93 28.52 27.49 52.09 7.17 8.29 8.17 10.38 10.37 13.33 13.27 16.58 16.59 31.70 30.53 57.86 7.89 9.12 8.99 11.42 11.41 14.66 14.60 18.24 18.26 34.87 33.57 63.64 8.61 9.95 9.81 12.46 12.45 16.00 15.93 19.90 19.92 38.05 36.61 69.41 9.33 10.78 10.63 13.50 13.49 17.33 17.26 21.56 21.59 41.22 39.65 75.19 10.05 11.62 11.45 14.54 14.53 18.67 18.59 23.22 23.25 44.40 42.68 80.96 NA 10.77 12.45 12.27 15.58 15.58 20.00 19.93 24.89 24.92 47.57 45.72 86.74 11.49 13.28 13.09 16.62 16.62 21.34 21.26 26.55 26.58 50.75 48.76 92.51 12.21 14.11 13.91 17.66 17.66 22.67 22.59 28.21 28.25 53.92 51.80 98.29 12.93 14.95 14.73 18.70 18.70 24.01 23.92 29.87 29.91 57.10 54.84 104.06 13.65 15.78 15.55 19.74 19.74 25.34 25.25 31.53 31.58 60.27 57.88 109.84 14.37 16.61 16.36 20.78 20.78 26.68 26.58 33.19 33.24 63.45 60.92 115.61 Note: If the screen is larger than 300 inches, then fine text and images may not display clearly. English 91 ADDITIONAL INFORMATION Projection distance The distance between the projector and its screen determines the approximate size of the image. The farther the projector is from the screen, the larger the projected image will be. The image size also varies depending on the aspect ratio, zoom and other settings. Projection distance Powered lens shift range Projection Lens BX-CTA15 Optical Lens Shift Range Ho Vo 30% 100% Become Dark Image H V 2% 50% V: Height of the projected image H: Width of the projected image Projected image When the lens is shifted beyond the described range of operation, screen edges may become darker or images may become out of focus. Note: The calculation is based on 1/2 image width and 1/2 image height. Mechanical Shift Range Max. of Hm Max. of Vm 40% 120% Projection Lens BX-CAA06/ BX-CTA06 BX-CTA17 Optical Lens Shift Range Ho Vo 30% 100% Become Dark Image H V 20% 80% V: Height of the projected image H: Width of the projected image Projected image When the lens is shifted beyond the described range of operation, screen edges may become darker or images may become out of focus. Note: The calculation is based on 1/2 image width and 1/2 image height. Mechanical Shift Range Max. of Hm Max. of Vm 40% 120% 92 English ADDITIONAL INFORMATION Projection Lens BX-CAA01/ BX-CTA01, BX-CAA03/ BX-CTA03, BX-CTA13 Optical Lens Shift Range Ho Vo 30% 100% Become Dark Image H V 30% 100% V: Height of the projected image H: Width of the projected image Projected image When the lens is shifted beyond the described range of operation, screen edges may become darker or images may become out of focus. Note: The calculation is based on 1/2 image width and 1/2 image height. Mechanical Shift Range Max. of Hm Max. of Vm 40% 120% Projection Lens BX-CTA16 Mechanical Shift Range Max. of Hm Max. of Vm +/- 24% 0/-24% V: Height of the projected image H: Width of the projected image Projected image When the lens is shifted beyond the described range of operation, screen edges may become darker or images may become out of focus. Note: · The calculation is based on 1/2 image width and 1/2 image height. · "Mechanical Lens Shift Range" for reference only and only can be moved under UST Test Pattern situation. English 93 ADDITIONAL INFORMATION Ceiling mount installation Projector dimensions All dimensions given in mm 1 Mounting holes for ceiling mount X Distance between projector and end of lens Lens type BX-CAA01/ BX-CTA01 BX-CAA03/ BX-CTA03 BX-CAA06/ BX-CTA06 BX-CTA13 BX-CTA15 BX-CTA16 BX-CTA17 Distance X (in mm) 61.6 81.4 80.9 109.1 68.9 315.5 103 Ceiling mount information If you wish to use a third party ceiling mount kit, please ensure the screws used to attach a mount to the projector meet the following specifications: Screw type: M6 x 4 Maximum hole depth: 10 mm Tightening torque: 25Kgf-cm~30Kgf-cm Note: Damage resulting from incorrect installation will void the warranty. 94 English ADDITIONAL INFORMATION IR remote codes Key Legend Key Position Repeat Format Address Data Byte 1 Byte 2 Byte 3 Byte 4 Description ON ( ) 1 F1 32 CD 2 FD Press to turn on the projector. OFF ( ) 2 1 3 2 4 3 5 4 6 5 7 6 8 F1 32 CD 2E D1 Press to turn off the projector. F1 32 CD 72 8D Use as numeric keypad number "1". F1 32 CD 73 8C Use as numeric keypad number "2". F1 32 CD 74 8B Use as numeric keypad number "3". F1 32 CD 75 8A Use as numeric keypad number "4". F1 32 CD 77 88 Use as numeric keypad number "5". F1 32 CD 78 87 Use as numeric keypad number "6". English 95 ADDITIONAL INFORMATION Key Legend Key Position Repeat Format 7 9 F1 8 10 F1 9 11 F1 Info ( ) 12 F1 0 13 F1 ID 14 F1 Auto 15 F1 Input 16 F1 UP () 17 F1 LEFT () 18 F1 Enter 19 F1 RIGHT () 20 F1 DOWN () 21 F1 Menu 22 F1 Exit 23 F1 Mode 24 F1 Bright. 25 F1 Contr. 26 F1 Pattern 27 F1 Lens Shift 28 F1 Lens Shift 29 F1 Focus 30 F1 Lens Shift 31 F1 Lens Shift 32 F1 Focus 33 F1 Keystone Keystone 34 F1 35 F1 Zoom 36 F1 Keystone 37 F1 Keystone 38 F1 Zoom 39 F1 Shutter (AV Mute) 40 F1 User 1 41 F1 User 2 42 F1 Address Data Byte 1 Byte 2 Byte 3 Byte 4 Description 32 CD 79 86 Use as numeric keypad number "7". 32 CD 80 7F Use as numeric keypad number "8". 32 CD 81 7E Use as numeric keypad number "9". 32 CD 82 7D Press to display source image information. 32 CD 25 DA Use as numeric keypad number "0". 32 CD A7 58 Press to set remote ID. Please refer to "Remote control ID setup" on page 27. 32 CD 4 FB Press to automatically synchronize the projector to the input source. 32 CD 18 E7 Press to select an input signal. 32 CD 0F F0 Press to select items or make adjustments to our selection. 32 CD 11 EE Press to select items or make adjustments to our selection. 32 CD 14 EB Press to confirm your item selection. 32 CD 10 EF Press to select items or make adjustments to our selection. 32 CD 12 ED Press to select items or make adjustments to our selection. 32 CD 0E F1 Press to display the on-screen display menus for projector. 32 CD 2A D5 Press to return to previous level or exit menus if at top level. 32 CD 5 FA Press to select the preset display mode. 32 CD 28 D7 Press to adjust amount of light in the image. 32 CD 29 D6 Press to adjust difference between dark and light. 32 CD 58 A7 Press to display a test pattern. 32 CD 41 BE 32 CD 42 BD Press to adjust the position of the image horizontally. 32 CD 86 79 Press to adjust focus to improve image clarity as desired. 32 CD 34 CB Press to adjust the position of the image vertically. 32 CD 32 CD Press to adjust the position of the image vertically. 32 CD 26 D9 Press to adjust focus to improve image clarity as desired. 32 CD 87 78 Press to adjust the horizontal keystone. 32 CD 51 AE Press to adjust the horizontal keystone. 32 CD 52 AD Press to adjust zoom to achieve a desired image size. 32 CD 53 AC Press to adjust the vertical keystone. 32 CD 54 AB Press to adjust the vertical keystone. 32 CD 55 AA Press to adjust zoom to achieve a desired image size. 32 CD 56 A9 Press to hide/unhide the screen picture. 32 CD 57 A8 Press to assign user functions. Please refer to "Remote Setup" on page 70. 32 CD 27 D8 Press to assign user functions. Please refer to "Remote Setup" on page 70. 96 English ADDITIONAL INFORMATION Troubleshooting If you experience a problem with your projector, please refer to the following information. If a problem persists, please contact your local reseller or service center. Image problems No image appears on-screen Ensure all the cables and power connections are correctly and securely connected as described in the Setup and Installation section. Ensure the pins of connectors are not crooked or broken. Ensure that the Shutter (AV Mute) feature is not turned on. Image is out of focus Press the Focus or Focus button on the remote control or projector keypad to adjust the focus until the image is sharp and legible. Make sure the projection screen is between the required distance from the projector. (Please refer to Image size and projection distance page 91). The image is stretched when displaying 16:10 DVD title When you play anamorphic DVD or 16:10 DVD, the projector will show the best image in 16:10 format on projector side. If you play 4:3 format DVD title, please change the format as 4:3 in projector OSD. Please setup the display format as 16:10 (wide) aspect ratio type on your DVD player. Image is too small or too large Press the Zoom or Zoom button on the remote control or projector keypad to adjust the projected image size. Move the projector closer to or further from the screen. From the OSD menu, select Display > Aspect Ratio to change the aspect ratio. Image has slanted sides: If possible, reposition the projector so that it is centered on the screen and below the bottom of the screen. Press the Keystone / / / buttons on the remote control to adjust the screen shape. Image is reversed From the OSD menu, select Device Setup > Projection > Rear to reverse the image so you can project from behind a translucent screen. Other problems The projector stops responding to all controls If possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before reconnecting power. Remote control problems If the remote control does not work Check that the operating angle of the remote control is pointed within ±30° horizontally or ±20° vertically to the IR receivers on the projector. Make sure there are not any obstructions between the remote control and the projector. Move to within 10 m (32.8 ft) of the projector. Make sure batteries are inserted correctly. Replace batteries if they are exhausted. English 97 ADDITIONAL INFORMATION LED status indicators Overview Light LED AV Mute LED Status LED Explanation Message Standby State Power on (Warm up) Power on & Laser diode on Power off (Cooling down) AV mute is off (Image is displayed) AV mute is on (Image is black) Projector communication Firmware upgrade Burn-in Factory reset Over temperature error Fan failure error Color wheel failure error Light LED Green Orange Red Steady Steady Steady Steady Steady Steady Status LED Green Orange Red Flashing Steady Flashing Steady Steady Flashing Flashing Steady Steady Flashing Steady Flashing Flashing AV Mute LED Green Orange Steady Steady Steady Steady Steady Note: Keypad LED (Power Key) will be in steady red for standby mode. 98 English ADDITIONAL INFORMATION Specifications Optical Resolution Lens Projection distance Description WUXGA (1920 x 1200) Power Zoom/Focus and full lens shift Please refer to "Throw Distance" spec. in "Image size and projection distance" on page 91. Electrical Inputs Outputs Control port Power requirement Description 2 x HDMI In (version 2.0) (with locking screw) 1 x DVI-D 1 x HDBaseT 1 x 3G-SDI In 1 x 3D SYNC In 1 x HDMI Out (version 2.0) (with locking screw) 1 x 3D SYNC Out 1 x RS232 (D-sub 9 pin) (PC Control) 1 x Wired in (3.5mm phone jack) (Remote In) 1 x 12V Trigger (3.5mm phone jack / Black) 1 x USB type A (5V/0.5A) 1 x RJ-45 (LAN) 2 x IR Receiver (Front / Top) 100-240V~ 50/60 Hz, 10A Mechanical Description Installation orientation 360° rotation, no restrictions Dimensions 484 (W) x 529 (D) x 207.8 (H) mm (w/o lens, with feet) 484 (W) x 529 (D) x 195 (H) mm (w/o lens, w/o feet) Environmental conditions Operating: 0°C ~ 40°C*(32~104°F); 10~85%RH, non-condensing Storage: -10°C ~ 60°C(14~140°F); 5~90%RH, non-condensing Note: If High Altitude >5000 ft, the system will be operated at the range of 0~35°C to ensure the normal operation of the projector. The light power will be reduced due to the high ambient temperature (35°C). Note: All specifications are subject to change without notice. English 99 ADDITIONAL INFORMATION Manual Warp Control Instruction 1. The Warp/Blend control option needs to be switched to the OSD option. Steps: Menu -> Display -> Geometric Correction -> Warp Control -> Advanced. 2. Changing the grid color can help to distinguish between grid color lines on each projector when completing the warping adjustment. The Warp/Blend grid color options include: Green (default), Magenta, Red, and Cyan. Steps: Menu -> Display -> Geometric Correction -> Advanced Warp -> Grid Color. 3. Set Blend overlap size. Steps: Menu -> Display -> Geometric Correction -> Advanced Warp -> Blend Setting -> Blend Width. The options and effective range of overlap size as follows: (a) Left: 0 (0%) / 192 (10%) ~ 960 (50%) (b) Right: 0 (0%) / 192 (10%) ~ 960 (50%) (c) Top: 0 (0%) / 120 (10%) ~ 600 (50%) (d) Bottom: 0 (0%) / 120 (10%) ~ 600 (50%) 3.1 Setup projectors and then set the overlap size according to the actual projection overlap. A. Make sure the overlap size for is smaller than the overlap size of actual projection. B. Turning on the blend width screen for all the projectors helps determine the effective overlap range. See below for settings for a 1x2 layout as an example, and follow the steps below: 3.2 Adjust the overlap size of right boundary of left projector first. A. The left side of the overlap area will shift along with the values of the blend setting. Overlap area is shown by a square with light color. B. Adjust overlap size until the left side of overlap area of left projector does not exceed the left boundary of right projector. 100 English ADDITIONAL INFORMATION 3.3 Adjust the overlap size of left boundary of right projector. A. The right side of overlap area will shift along with the values of blend setting. Overlap area is shown by a square with light color. B. Adjust the value of the blend setting to the same as the overlap size of the right boundary of left projector. C. Make sure the right side of overlap area does not exceed the right boundary of left projector. D. If not, reduce the value of blend setting until the result matches the condition of step C. E. If the value of the blend setting of the right projector is less than left projector, adjust the value of left projector to the same as right projector. 4. Use grid points and warp inner to complete the warping calibration. A. Grid points options include: 2x2 (default), 3x3, 5x5, 9x9, and 17x17. Note: 1. Use , , or buttons to select the grid point. 2. Press Enter button to select the point. 3. Then press , , or buttons to shift the selected point location. 4. Press to return to the previous page. B. Warp inner: Turn On/Off inner control. Note: Warp inner does not support 2x2 grid point. C. The overlap area is divided into four parts equally in warping pattern. English 101 ADDITIONAL INFORMATION D. Use the warp adjustment to align the grid lines of the overlap with the two projectors to finish manual blending. Follow the steps below: (1) Select grid point 2x2 and align boundary of projectors with the side of overlap areas. (2) Depending on the installation situation select grid points 3x3, 5x5, 9x9, or 17x17 to adjust the grid line. (3) Turn on warp inner to adjust the inner grid. (4) All the grid lines are aligned. Press "Exit" button to exit grid pattern and then manual blending setting is finished. 5. When the grid lines are warped from straight to curve, the grid lines may become distorted or jagged. To avoid this users can adjust the warp sharpness to blur or sharpen the edge of the images. 102 English ADDITIONAL INFORMATION Optoma global offices For service or support, please contact your local office. USA Optoma Technology, Inc. 47697 Westinghouse Drive. Fremont, Ca 94539 Canada Optoma Technology, Inc. 47697 Westinghouse Drive. Fremont, Ca 94539 Latin America Optoma Technology, Inc. 47697 Westinghouse Drive. Fremont, Ca 94539 China 888-289-6786 Room 2001, 20F, Building 4, 510-897-8601 No.1398 Kaixuan Road, services@optoma.com Changning District Shanghai, 200052, China www.optoma.com.cn 888-289-6786 510-897-8601 Japan services@optoma.com https://www.optoma.com/jp/ 888-289-6786 Korea 510-897-8601 services@optoma.com https://www.optoma.com/kr/ Europe Unit 1, Network 41, Bourne End Mills Hemel Hempstead, Herts, HP1 2UJ, United Kingdom www.optoma.eu Service Tel : +44 (0)1923 691865 Benelux BV Randstad 22-123 1316 BW Almere The Netherlands www.optoma.nl Taiwan https://www.optoma.com/tw/ +44 (0) 1923 691 800 +44 (0) 1923 691 888 service@tsc-europe.com Australia https://www.optoma.com/au/ +31 (0) 36 820 0252 +31 (0) 36 548 9052 France Bâtiment E 81-83 avenue Edouard Vaillant 92100 Boulogne Billancourt, France +33 1 41 46 12 20 +33 1 41 46 94 35 savoptoma@optoma.fr Spain C/ José Hierro,36 Of. 1C 28522 Rivas VaciaMadrid, Spain +34 91 499 06 06 +34 91 670 08 32 Deutschland Am Nordpark 3 41069 Mönchengladbach Germany +49 (0) 2161 68643 0 +49 (0) 2161 68643 99 info@optoma.de Scandinavia Lerpeveien 25 3040 Drammen Norway PO.BOX 9515 3038 Drammen Norway +47 32 98 89 90 +47 32 98 89 99 info@optoma.no +86-21-62947376 +86-21-62947375 servicecn@optoma.com.cn English 103 www.optoma.com
europe.com
JBMIA PJLink
AMX Audio Video Control Systems | English (US)
Control Systems for Home Automation, Campus & Building Control by Crestron Electronics [Crestron Electronics, Inc.]
Extron - The AV Technology Leader
Optoma China
Projectors for home and business, LED displays, IFPDs, screens | Optoma United Kingdom
Projectors for home and business, LED displays, IFPDs, screens | Optoma Nederland
Optoma Download CenterExperience More | Optoma USA