NVK Dog Training Collar

Dog-Training-Collar-illustration

COMPONENTS

diagram, engineering drawing

shape

a drawing of a clip

OVERVIEW

Handheld Remote

diagram

Screen

diagram

Receiver

diagram

diagram

Important Safety Information

icon WARNING: indicates a hazardous situation which, if not avoided, could result in serious injury.

iconCAUTION
Caution: used with the safety alert symbol, indicates a hazardous situation, which, if not avoided could result in minor or moderate injury.

  • Safety during on-leash training. It is vitally important that you and your dog remain safe while learning during on-leash training. Your dog should be on a strong leash, long enough for him to attempt to cha.se an object, but short enough for him not to reach a road or other unsafe area. You must also be physically strong enough to restrain your dog when he tries to chase.
  • This pet training device is not a toy, keep away from children.

icon CAUTION
Caution: used without the safety alert symbol, indicates a hazardous
situation, which, if not avoided, could result in harm to your pet.

Risk of skin damage. Please read and follow the instructions in this manual. Proper fit of the collar is important. A collar worn for too long or made too tight on the pets neck may cause skin damage. Ranging from redness to pressure ulcers; this condition is commonly known as bed sores.

  • Avoid leaving the collar on the dog for more than 12 hours per day.
  • Possible reposition the collar on the pet’s neck every 1 to 3 hours.
  • Check the fit to prevent excessive pressure; follow the instructions in this manual.
  • Never connect a leash to the electronic collar; it will cause excessive pressure on the contact points.
  • When using a separate collar for a leash, don’t put pressure on the electronic collar.
  • Wash the dog’s neck area and the contacts of the collar weekly with a damp cloth.
  • Check the contact area daily for signs of a rash or a sore.
  • If a rash or sore is found, discontinue use of the collar until the skin has healed.
    If the condition persists beyond 48 hours, see your veterinarian.

COMPONENTS DETAIL

  1. Charge the Collar and Remote
    Charge-Collar-and-Remote-illustration

    When charging is completed, the green light will appear.
  2. Fit the Receiver Collar
    Fit-Dog-Receiver-Collar

    Note: The Contact Points must have direct contact with Dog’s skin on the underside of neck. Check the tightness of the Collar by inserting one finger snugly between the collar and neck.
  3. To turn the Remote and Receiver on
    Remote-&-Receiver-illustration

    When not using the collar, turn it off to increase the battery life. Long press the button 3 secs to turn off the Receiver.
  4. Keypad Lock
    Keypad-Lock-Instructions-illustration
            Security Keypad : lock or unlock
  5. Beep Tone command
    Remote-Beep-Tone-command-illustration
    Delivers a beep tone with non- adjustable volume to the collar.
  6. Vibration command
    Remote-Vibration-command-illustration
    Delivers vibration to the collar. Vibration Intensity adjustment: Press and hold the vibration Level button B, at the same time, rotating the level regulator A of the remote.
  7. Static Stimulation command
    Device-Static-Stimulation-command-illustration
  • Static button: Delivers currently selected level Static stimulation to the collar.
  • Static+ button: That is 10% higher than the currently selected level. Some consumers would like to instant access to a higher setting where the dog may not respond to lower levels.
  • Static Intensity adjustment: Press and hold the static Level button C, at the same time, rotating the level regulator A of the remote.

icon How to find the Best Static Level for Your Dog ? 

Very Important: Always start at the lowest level and choose the level that is best for your dog.
Have 1 to 99 different Stimulation Levels. Follow the steps below to find the best Level:

  • Step 1: Starting at Level 1 o on the Digital Display, press the static button to see dog’s reaction.
  • Step 2: Move up through the Stimulation levels until your pet reliably responds to the Stimulation.
  • Step 3: If your dog continues to show no response at Level 50, check the fit of the Receiver Collar. If your dog has long or thick hair, change to a longer set of Contact Points, or dog’s hair will need to be trimmed around the Contact Points.
  • If all of these steps have been done and dog continues to show no reaction, see the “How to use Test light Tool” section.

Main Features

Vibration-Tone-Static-training-model-Symbol Vibration, Tone and Static training model
adjustable-level-Symbol 9 adjustable vibration level and 99 adjustable static level
Dual-batteries-Symbol Dual batteries status display for Remote and Receiver
Non-waterproof-Symbol Receiver collar IPX7 waterproof (Remote non-waterproof)
WIFI-Icon Remote range 1000-1 600 feet
Long-life-Battery-Symbol Long life Lithium Polymer battery
Big-digital-display-Symbol Big digital display
 receiver-collars-symbol Support maximum 4 receiver collars with one remote
Magnetic-charging-port-symbol Magnetic charging port

How to use Test Light Tool

A: Static function test

  1. Make sure the Remote and Receiver Collar on.
  2. Hold the Test Light tool contacts to the Contact Points.
  3. Press a Static button on the Remote Transmitter. The Test Light will be lighted.
    Testing-Light-Tool-illustration

B: As a tool to tighten or loosen the contact points

For dog with shorter coats, use 2pcs shorter contact point. Or install the conductive Silicone onto the contact point to make it softer. It may better to your dog’s skin.
For dog with thicker coats, use 2pcs longer contact points. Or install the conductive Silicone.

Testing-Light-Tool-illustration
Testing-Light-Tool-illustration

Training Tips

If you wan to eliminating unwanted behavior – For examples barking. Please follow these training steps.

  1. Put a separate non-metallic collar on your dog’s neck above the Receiver Collar, and attach a 8- 10 foot leash. ( Note: Be sure the extra collar does not put pressure o n the Contact Points. )
  2. Hold the leash and the Remote Transmitter
  3. Choose your pet’s Recognition Level.
  4. As soon as your pet is barking, press the Stimulation button and give the command “No” or” No barking.”
  5. Release the Stimulation button immediately once your dog stop barking, and verbally praise him.
  6. If your pet ignores the stimulation, increase the Intensity Level by 3 to 5.
  7. Practice this exercise in several different areas.

Pairing

( Notes: You may skip this step because the set is already paired by factory setting. )

  1. Make sure the Receiver is turned off.
  2. Press and hold Switch for 5 secs until the green light is flashing fast.
    Pairing-Device-Instruction-illustration
  3. Press the remote Pairing/Channel Select button D to paring the receiver.
    Pairing-Device-Instruction-illustration
  4. Pairing successful: the receiver will beep and t he green light flash slowly.
    Pairing-Device-Instruction-illustration

Two, Three, Four Receiver System

( Note: Please skip this step if you only use one receiver. This setting only for multiple receiver with one remote.)

Part I : Pairing 2nd, 3rd, or 4th Receiver.

( Note: You should buy an additional receiver collar.)

● Receiver:

  1. Make sure the Receiver is turned off.
  2. Press and hold Switch for 5 secs until the green light flashes fast.
    ● Remote:
  3. Press and hold channel button D, at the same time, rotating the level
    regulator A to select the dog icon. ( For examples Dog 2, the Dog 2 icon will flash.)
  4. Press the remote Pairing/Channel Select button D to paring the receiver.

Part II : Receiver Switching:

  • Able to train 4 dogs at the same time.
  • Press and hold channel button D, .at the same time, rotating the level regulator A to select the dog to train.

Part Ill: Reset all paired receiver collar.

  • Make sure the remote is “ON”.
  • Press and hold Static level button C and Vibration level button B, at the same time, turning the regulator switch A OFF to ON. All paired receiver will be removed and the dog 1 icon w1ill flash.
  • Pairing the receiver again.

Question & Answer

How to change the longer prongs for this collar? I don’t think they are getting through my Labs thick hair.

Answer:
Just part the hair or trim it a bit. I have a dog with very thick neck of hair. I parted it with my hands . Just be sure remote is off then start on low setting and work your way up. If no response repeat steps of working prongs thru hair remember to turn off or lock remote.

Troubleshooting

  1. My pet is not responding when I press a beep vibration or static button.
    Check the Receiver Collar if it is On.
    Please check to see if the battery is low in either the Remote Transmitter or Receiver Collar.
    Verify the Receiver Collar is delivering Stimulation to your pet by placing the Test Light, enclosed in your kit, on the Receiver Collar.
    Increase the correction level. Refer to “Find the Best Stimulation Level For Your dog”.
    Make sure the Receiver Collar’s Contact Points are placed snugly against your pet’s skin.
  2. The Receiver Collar will not turn on.
    Make sure the Receiver Collar has been charged.
  3. The Receiver Collar is not responding to the Remote Transmitter.
    Verify the Receiver Collar has been turned on.

Compliance

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION: Modification or changes to this equipment not expressly approved by Radio Systems Corporation may void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a specific installation. If interference does occur to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
  • Consult customer care, the dealer, or an experienced radio/TV technician for help

NVK Dog Training Collar Manual – Download [optimized]
NVK Dog Training Collar Manual – Download

Join the Conversation

27 Comments

    1. Yes. The collar and receiver is waterproof but the remote control is not.

  1. I received my NVK shock collar on May 6, 2021 I have charged it, but now it will not charge. Need help.

  2. I have a NVK dog collar. The collar was working fine. Then it stopped and I realized it was no longer paired. I have followed the instruction to UN-pair the collar and reset it. It will not pair. Both collar and remote are charged. I have tried multi times to pair.
    1. I do not understand why it all of sudden became un-paired ?
    2. the dog icon flashes on the remote control. But will not pair the collar to the remote.
    3. is there some secret to the STEPS in pairing or is the collar / remote broken ??

  3. I have the same problem as Don. The unit will not pair. Should you replace the defective transmitter and receiver?

  4. I’ve had this shot collar for 3 months now all of a sudden it won’t pair with the receiver. Battires are all charged.

  5. Can the contact points (shock prongs) be removed? I only want to use the sound/vibrate feature. The prongs are very aggressive and my dog is responding to the sound.

  6. i have the same problem as the comment before mine! i had one and it was working fine then i bought a second one and tried to pair it to the remote. now neither collar works and the only thing the remote will do is flash the channel 1 dog. i have tried to reset it but it will not do anything other then flash. i have emailed support multiple times and no response. please help!

  7. Why is the collar beeping? Its scaring the crap out of my dog and I am not pressing any buttons for the collar to beep.

  8. I purchased my NVK collar about two months ago, I noticed that the shock collar and the transmitter don’t communicate anymore. What do I need to do to get it work again.

  9. The manufacturer’s instructions makes the assumption that one has already purchased another type of collar and are now ready to use theirs. Can someone just write a manual to tell me how to set it up. I push the buttons as instructed and the responses are not as they describe. Classic instructions where the teacher assumes that me, the student, already knows how to use the product. Ridiculous.

  10. I need to order the tool that tightens or loosens the contact points, and also I need to order 2 long contact points and the conductive Silicone for the long contact points and also conductive Silicone for the short contact points….
    Our original ones were accidentally thrown out after our dog chewed up the box that they were still in.
    Thank You

  11. Does anyone know if I can purchase just the charger, I have misplaced mine and can’t charge the collar.

  12. Everything was working fine the first day. But now only the vibrate works but the shock feature doesn’t. What’s up?

  13. The remote will charge but the collar will not charge at all. How do I fix this?

  14. CAN THE TIME DELAY BE TURND OFF ON THE BEEP AND VIBRATE BUTTONS DOG IS SO FAST SE CAN GO TO FAR IN THE TIME IT TAKES TO TRANSMITT
    PLEASE RESPOND ED

  15. My 45 pound dog yipes when the shock level is on one. Is this normal or is my collar malfunctioning.

Ask a question

Your email address will not be published.