nVent FLEXCOND50 Eriflex Flexbus Supports and Bracing System
INSTRUCTION SHEET
On Edge Support Kit
| Configuration | 1 Conductor per Phase  |
2 Conductors per Phase  |
| 3P |  |
 |
| 3P+N |  |
 |
Flat Support Kit
| Configuration | 1 Conductor per Phase |
2 Conductors per Phase  |
| 3P |  |
 |
| 3P+N |  |
 |
| CONFIGURATION | FLEXCOND50 | FLEXCOND100 | |||||||||||||
| L1 | # L1 | E1 | S | Lr | # Lr | D | L1 | # L1 | E1 | S | Lr | # Lr | D | ||
| 3P (I) |  |
287,5 | 3 | 12,5 | 87,5 | 150 | 4 | 262,5 | 325 | 3 | 12,5 | 100 | 186 | 4 | 300 |
 |
112,5 | 7 | 12,5 | 87,5 | 420 | 2 | 87,5 | 162,5 | 7 | 12,5 | 137,5 | 186 | 2 | 137,5 | |
 |
287,5 | 3 | 12,5 | 87,5 | 150 | 4 | 262,5 | 437,5 | 3 | 12,5 | 137,5 | 290 | 4 | 412,5 | |
| 3P (II) |  |
550 | 3 | 12,5 | 87,5 | 150 | 7 | 525 | 625 | 3 | 12,5 | 100 | 186 | 7 | 600 |
 |
287,5 | 5 | 12,5 | 87,5 | 245 | 4 | 262,5 | 325 | 5 | 12,5 | 100 | 343 | 4 | 300 | |
 |
200 | 7 | 12,5 | 87,5 | 420 | 3 | 175 | 300 | 7 | 12,5 | 137,5 | 420 | 3 | 275 | |
 |
287,5 | 5 | 12,5 | 87,5 | 290 | 4 | 262,5 | 437,5 | 5 | 12,5 | 137,5 | 290 | 4 | 412,5 | |
| 3P + N (I) |  |
375 | 3 | 12,5 | 87,5 | 150 | 5 | 350 | 425 | 3 | 12,5 | 100 | 186 | 5 | 400 |
 |
200 | 5 | 12,5 | 87,5 | 245 | 3 | 175 | 225 | 5 | 12,5 | 100 | 343 | 3 | 200 | |
 |
200 | 5 | 12,5 | 87,5 | 290 | 3 | 175 | 300 | 5 | 12,5 | 137,5 | 290 | 3 | 275 | |
 |
112,5 | 9 | 12,5 | 87,5 | 550 | 2 | 87,5 | 162,5 | 9 | 12,5 | 137,5 | 550 | 2 | 137,5 | |
 |
375 | 3 | 12,5 | 87,5 | 150 | 3 | 350 | 575 | 3 | 12,5 | 137,5 | 186 | 3 | 550 | |
| 3P + N (II) |  |
725 | 3 | 12,5 | 87,5 | 150 | 9 | 700 | 825 | 3 | 12,5 | 100 | 186 | 9 | 800 |
 |
375 | 5 | 12,5 | 87,5 | 245 | 5 | 350 | 425 | 5 | 12,5 | 100 | 343 | 5 | 400 | |
 |
200 | 9 | 12,5 | 87,5 | 550 | 3 | 175 | 300 | 9 | 12,5 | 137,5 | 550 | 3 | 275 | |
 |
375 | 5 | 12,5 | 87,5 | 290 | 5 | 350 | 575 | 5 | 12,5 | 137,5 | 290 | 5 | 550 | |
WARNING
- nVent products shall be installed and used only as indicated in nVent product instruction sheets and training materials. Instruction sheets are available at www.nVent.com and from your nVent customer service representative.
- nVent products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.
- All instructions must be completely followed to ensure proper and safe installation and performance.
- Improper installation, misuse, misapplication or other failure to completely follow nVent’s instructions and warnings may cause product malfunction, property damage, serious bodily injury and/or death, and void your warranty.
SAFETY INSTRUCTIONS: All governing codes and regulations and those required by the job site must be observed. Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.
nVent, nVent CADDY, nVent ERICO Cadweld, nVent ERICO Critec, nVent ERICO, nVent ERIFLEX, and nVent LENTON are owned by nVent or its global affiliates. All other trademarks are the property of their respective owners. nVent reserves the right to change specifications without prior notice.
TECHNICAL SUPPORT:
www.nVent.com
Documents / Resources
 |
nVent FLEXCOND50 Eriflex Flexbus Supports and Bracing System [pdf] Instruction Manual FLEXCOND50 Eriflex Flexbus Supports and Bracing System, FLEXCOND50, Eriflex Flexbus Supports and Bracing System, Flexbus Supports and Bracing System, Supports and Bracing System, Bracing System |
 |
nVent FLEXCOND50 Eriflex Flexbus Supports And Bracing System [pdf] Instructions FLEXCOND50 Eriflex Flexbus Supports And Bracing System, FLEXCOND50, Eriflex Flexbus Supports And Bracing System, Flexbus Supports And Bracing System, Bracing System |
