MODEL NO,AP1
USER MANUAL 
AP1 Jump Starter with Air Compressor
Please read user manual before using, and keep it for further reference
Please carefully read the instruction manual and use product correctly based on the instruc- tion manual so that you can be familiar with the product more conveniently and quickly! Perhaps there is small difference between the photo and the actual product, so please turn to the actual product for detail information.
Packing list
Parts and Function Description
- Display Screen
- PUMP Button
- BAR/PSI Button
- + Button
- – Button
- Light
- + Button
- – Button
- Light
- Light Button
- DC Out Port
- USB Out Port
- TYPE-C In/Out Port
| Part Name | Function |
| POWER Button | Short press to tur on the device |
| PUMP Button | Short press the button and the screen will display “KPA”, the default value is 250″ Long press to start inflation |
| LIGHT Button | Long press to tur on light, short press to switch light mode |
| + Button | Pressurize |
| – Button | Depressurize |
| BAR/PSI Button | First press the “PUMP” button, then press the “BAR/PSI” button to switch the inflation unit (BAR, PSI) |
Specifications
| Model | AP1 |
| Start Voltage | 12v |
| Peak Current | 4000A |
| Type-C In(Out) | 5V~3A 9V-3A 12V~3A 15V~3A 20V-3A(60W MAX) |
| USB Out | 5V~3A 9V-2A 12V-1.5A(18W MAX) |
| DC Out | 12~16.8V=10A |
| Unit Display | KPA/BAR/PSI |
| Adjustable Pressure Range | 1-1000KPA/0.1-10.0BAR/1-150PS| |
Operation guide
Please note before use:
- Adapter is not included.
- When using the product for the first time, please make sure it s fully charged.
- Itis recommended to charge the product every 3 months to prolong s life even if the unit is not in use.
Recharge the product
Step 1. Connect the product to a power source via the charging cable.
Step 2. Disconnect the power after fully charged.
Step 1. Connect the product to your iPhone, smartphone, or other USB electronic devices via the charging cable.
Step 2.
Press the power button to start charging. Disconnect when charging is not required.
LED flashlight
Long press the light button for 3 seconds, and the white flashlight will be on. Short press to switch to Strobe and SOS mode in turn.
Then press again to turn it off.
Start Vehicles
Before use, please note
- This product is only suitable for 12V vehicles
- Before starting your car, it’s best to make sure the product has enough power.
Step 1.
Insert the jumper cable plug into the jump starter.
When the indicator light of the jumper cable is blue, it means the jumper cable is in standby status.
Step 2.
Connect the clamp to the car battery. Connect the red clamp cable to the positive and the black clamp cable to the negative. Please avoid reverse connection.
Step 3.
When the indicator light of the jumper cable is green, you can try to start your vehicle.
Step 4.
After jump-starting the engine, remove the battery clamp from the car battery. then remove the clamp plug from the jump starter.
Inflate Tires
Step 1.
Connect the inflation hose firmly to the product and the tire air valve respectively.
Step 2.
Short press the power button to activate the product, then press the “PUMP” button, the screen displays KPA (default 250), then press the “BAR/PSI” button to switch the inflation unit, BAR (default 2.5), PSI (default 36) . And press the “+” and “-” buttons to adjust the pressure value.
Step 3.
After the setting is completed, press and hold the “PUMP” button for three seconds to start Inflate and display real-time tire air values.
Step 4.
The product will stop automatically after reaching the preset pressure value.
Tips: If you use it for a long time, it is recommended to stop every 10 minutes to cool down.
Abnormal Indication of Jumper Cable
| LETTER | STAND FOR | SOLUTION |
 | Low Capacity | Please charge jump starter |
 | Reverse Connection | Please exchange positive and negative poles of the jumper cable |
 | High Temperature | Please wait 5 mins before starting the car |
Forbid to use this clamp in an environment full of flammable gas.
Jumper Cable Indicator Instruction
Jumper Cable Indicator Instruction
| STATUS | TECHNICAL PARAMETER | DESCRIPTION | SOLUTION |
| Standby indication | Blue light | Jumper cable connect to jump starter, then blue light on | / |
| Automatic conduction status indicator (ready to jump start your car) | Green light | Jumper cable connect to the car battery after connecting the jump starter, then green light on | / |
| Force start function | Start the car within 30s | If the above operations cannot start your car, please use the forced start function | Fart Ensure the correct connection of clamps before using force start function, long press the force start button for 3 seconds until green light on |
| Reverse connection protection | RC | Wrong connection between jumper cable and car’s positive and negative poles. The RC red light stays on | Keep the correct connection, the positive pole (red)and the positive pole are connected, the negative pole(black) and the negative pole are connected |
| High temperature protection | YES | The HT red light stays on and beep long alarm sound; Cut off voltage output | Automatically recover when the temperature drops |
| Start timeout protection | 40S±5S | Automatically enter the standby state after more than 40 seconds and The LED blue light stays on | You can use it again after disconnecting for a minute |
| Input low capacity protection | 13.5V±0.5V | When it is detected that the power of the EC5 port is lower than 13.5V, there is no output at this time, the LC red light stays on and beep long alarm sound | Please charge jump starter |
| Short circuit protection | YES | No response | Please use the positive and negative poles of jumper cable to connect the positi |
Abnormal Indication of Jumper Cable
Q1: What is the service temperature of this product and how to store it? A: The working temperature is 0°C-45°C. If the ambient temperature is higher than 45°C, the internal instructions of the lithium-ion battery will change. It can expand and is not safe, so don't store it in the car for a long time, especially in summer. Q2: How long can the storage capacity of the battery last? A: 4-6 months. However, we recommend charging it every 2-3 months to keep your jump starter healthy. Q3: What should | do if this product does not charge? A: Charge it with a 5V charger and a type-c cable, and wait overnight. If it stll doesn't work, please contact us. Q4: Can this starter start a 24V truck? A: The AP1 jump starter is only suitable for 12V batteries. Q5: What to do if the machine inflates slowly A:1. Check whether the power is sufficient. 2. Check whether the air inflation tube is leaking. 3. Check whether the connection parts at both ends of the tube are tightened. 4. Check whether the inflated objects are leaking. Q6: What should | do if the battery cannot be inflated? A: 1. Check whether the power is sufficient 2. Check whether the current tire pressure is higher than the preset value. Q7: What to do if there is a leak in the connecting air hose? A: Tighten the connecting air hose. Q8: In other cases, what should | do if the machine operation does not respond? A: Restart the machine
Safety Warning
- Never short circuit the jump starter by connecting the Red and Black clamps.
- If you find swelling, leakage, or odor, please stop using the jump starter immediately.
- Please use this starter at normal temperature and keep it away from humid, hot fireplaces.
- When the battery power is less than 10%, do not use the jump starter otherwise the device will be damaged.
- Before first use please charge it for 3 hours or more.
Note:
– For the first use, please make sure to fully charge before use.
– In normal use, please confirm that the unit has at least 50% power before use.
Warranty Exception
- The product has been incorrectly operated or damaged due to the following irresistible reasons (such as flood, fire, earthquake, lightning, etc).
- The problem is caused by the wrong charger does not match the product.
- Beyond the product warranty period(12 months)ol>
Documents / Resources
NEXPOW AP1 Jump Starter with Air Compressor [pdf] User Manual
AP1 Jump Starter with Air Compressor, AP1, Jump Starter with Air Compressor, Starter with Air Compressor, Air CompressorReferences