WLTK1010BK Doorbell

Nedis WLTK1010BK Doorbell

User Manual


Thank you for purchasing the Nedis DOORB212WT.
This document is the user manual and contains all the information for correct, efficient and safe use of the product.
This user manual is addressed to the end user. Read this information carefully before installing or using the product.
Always store this information with the product for use in the future.
Product description
Intended use
The product is intended as a wireless doorbell.
The product consists of a receiver and a transmitter.
The transmitter and the receiver are powered by a battery.
The doorbell receiver is for indoor use only.
Any modification of the product may have consequences for safety, warranty and proper functioning.
Wireless doorbell
Article number
Dimensions (d x w x h)
42 x 78 x 115 mm
21 x 31 x 80 mm
Battery type
2 x AA (not included)
CR2032 (lithium)
433.90 – 433.94 MHz
> 80 dB @ 0.5 m
Operating range
max 300 m
Main parts (image A)
2_20001 1422 Nedis - Doorbell DOORB212WT - parts (OH) OH v3
1. Sound only
2. Flashing LED only
3. Sound and flashing LED
4. Mode
5. Volume button
6. Pairing mode button
7. Choose tune button
8. LED indicator
9. LED indicator
10. Doorbell

Safety instructions

  • Only use the product as described in this manual.
  • Read the manual carefully before use. Keep the manual for future reference.
  • Do not use the product if a part is damaged or defective. Replace a damaged or defective product immediately.
  • Do not drop the product and avoid bumping.
  • This product may only be serviced by a qualified technician for maintenance to reduce the risk of electric shock.
  • Disconnect the product from the power source and other equipment if problems occur.
  • Do not expose the product to water or moisture.
  • Retain the original product literature for future reference.
  • Non-rechargeable batteries are not to be recharged.
  • Do not dismantle, open or shred batteries.
  • Do not expose cells or batteries to heat or fire. Avoid storage in direct sunlight.
  • Do not short-circuit a cell or a battery.
  • Do not store cells or batteries haphazardly in a box or drawer where they may short-circuit each other or be short-circuited by other metal objects.
  • Do not remove a cell or battery from the original packaging until required for use.
  • Do not subject cells or batteries to mechanical shock.
  • In the event of a cell leaking, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice.
  • Observe the plus (+) and minus (–) marks on the cell, battery and equipment and ensure correct use.
  • Do not use any cell or battery that is not designed for use with the product.
  • Seek medical advice immediately if a cell or a battery has been swallowed.
  • Always purchase the battery recommended by the product manufacturer for the product.
  • Keep cells and batteries clean and dry.
  • Wipe the cell or battery terminals with a clean dry cloth if they become dirty.
  • Use only the cell or battery in the application for which it was intended.
  • When possible, remove the battery from the product when not in use.
  • Properly dispose of the empty battery.
  • Do not mix cells of different manufacture, capacity, size or type within a product.
  • Battery usage by children should be supervised.
  • Disconnect the power supply before making or breaking the connections to the battery.
  • Batteries contain explosive gases. Prevent contact with flames and sparks. Provide adequate ventilation during charging.
Safety symbols on the product
Electronic equipment needs to bear the CE mark in order to be marketed in the EU. CE marking shows that a product is assessed before being placed on the market and that it meets EU safety, health and environmental protection requirements. CE marking is also sometimes accepted as a means of compliance with type-approval requirements; for example, electronic components that require type-approval and also CE marking for electromagnetic compatibility (EMC) or low-voltage equipment.
Electrical Class 2
Product in which protection against electric shock does not rely on basic insulation only, but in which additional safety precautions such as double insulation or reinforced insulation are provided, there being no provision for protective earthing or reliance upon installation conditions NOTE A Class II products may be provided with means for maintaining the continuity of protective circuits, provided that such means are within the product and are insulated from accessible surfaces according to the requirements of Class II.
Green Dot
Indication that the producer of the packaging material complies with the Packaging Law and has contributed to the costs of the ‘Green Dot’ waste separation and recycling system.
Indication to explain that the product needs to be collected separately when disposed. Do not throw in the trash bin.
Indication to explain that the product can be recycled.
Triman recycling
Indication to explain that the product should be recycled appropriately.
Indication to explain that the product needs to be collected separately when disposed. Do not throw in the trash bin.


  • Check the contents of the package
  • Check that all parts are present and that no damage is visible on the parts. If parts are missing or damaged, contact the Nedis B.V. service desk via the website: www.nedis.com.
Place the battery (receiver)