KRAMER KIT-401 Auto Switcher 
Quick Start Gwida
This guide helps you install and use your KIT-401 for the first time. Go to www.kramerav.com/downloads/KIT-401 to download THE latest user manual and check if firmware upgrades are available.
Iċċekkja x'hemm fil-kaxxa
KIT-401, including:
KIT-401T 4K HDMI/PC Auto Switcher Transmitter and KIT-400R 4K HDBT/HDMI Receiver/Scaler 1 Power adapter, cable adapter and cord 4 Rubber feet 1 Quick start guide Installation accessories 2 Bracket sets (KIT-400R) 1 Frame or frame kit (KIT-401T)
Get to know your KIT-401
KIT-401T
| # | karatteristika | funzjoni | |
| 1 | ETHERNET LAN RJ-45 Connector | Connect to the LAN (Ethernet traffic or PC controller). | |
| 2 | Konnettur HDMI ™ IN | Qabbad ma 'sors HDMI. | |
| 3 | Buttuna RESET | Sends a reset command to KIT-400R and then reboots KIT-401T. | |
| 4 | HDMI | LED Indikatur | Lights green when the HDMI source is selected as the input. Lights red when analog audio is selected. |
| PC | Lights green when the PC source is selected as the input. Lights red when analog audio is selected. | ||
| REMOTE | Lights green when the HDMI INPUT source on KIT-400R is selected as the input. | ||
| 5 | AWDJO IN 3.5mm Mini Jack | Connect to an unbalanced, stereo audio source (for example, the audio output of the laptop). | |
| 6 | PC 15-pin HD Connector | Connect to a PC graphics source. | |
| # | karatteristika | funzjoni | |
| 7 | 12V Power Supply 2-pin Terminal Block Connector | Connect to the supplied power adapter (if required). Connect + to +, – to -. Follow powering instructions in Pass 5: Qabbad l-enerġija. | |
| Connect power to either this terminal block or to the KIT-400R 12V power connector (item 34). Do not connect to both! | |||
| 8 | RS-232 | DATA 3-pin Terminal Block Connector | Connect to a serial data source or acceptor. |
| 9 | CONTROL 3-pin
Terminal Block Connector |
Connect to a serial controller or PC. | |
| 10 | Remote Contact-closure 4-pin Terminal Block Connector | Connect to contact closure switches (by momentary contact between the desired pin and GND pin) to select an input, the remote HDMI IN and audio volume (up or down), see Pass 6: Operate KIT-401. | |
| 11 | SETUP 4-way DIP-switch | Set the device behavior, see Pass 4: Connect inputs and outputs. | |
| 12 | Invita għall-ert tat-Terminal tal-Ilsien taċ-Ċirku | Qabbad mal-wajer tal-ert (mhux obbligatorju). | |
| 13 | HDBT OUT (PoC) RJ-45 konnettur |
Qabbad KIT-400R. | |
| 14 | AUDIO OUT 3.5mm Mini Jack | Connect to the unbalanced, stereo audio acceptor (for example, kelliema attivi). | |
It-termini HDMI, HDMI High-Definition Multimedia Interface, u l-Logo HDMI huma trademarks jew trademarks irreġistrati ta 'HDMI Licensing Administrator, Inc.
KIT-400R
| # | karatteristika | funzjoni | |
| 15 | PROG Konnettur USB | Connect to a USB stick to perform firmware upgrades. | |
| 16 | Dħul | Buttuna SELECT | Press to select the input (HDBT or HDMI). |
| 17 | HDBT LED | Lights blue when the HDBT input is selected. | |
| 18 | LED LED | Lights blue when the HDMI input is selected. | |
| 19 | Buttuna MENU | Press to enter/exit the on-screen display (OSD) menu. Press together with the – button to reset to 1080p. | |
| 20 | Buttuna ENTER | In OSD, press to choose the highlighted menu item. Press together with the FREEZE/+ button to reset to XGA. | |
| 21 | - | In OSD, press to move back through menus or decrement parameter values. | |
| 22 | FREEZE/+ Button | In OSD, press to move forward through menus or increment parameter values. When not in OSD, press to freeze the display. | |
| 23 | LINK LED | Lights blue when a link is established with the transmitter. | |
| 24 | LED ON | Lights green when device is powered. | |
| 25 | Dħul | Konnettur HDBT RJ-45 | Qabbad KIT-401T. |
| 26 | Konnettur HDMI™ | Qabbad ma 'sors HDMI. | |
| 27 | OUTPUT | Konnettur HDMI | Qabbad ma 'aċċettatur HDMI. |
| 28 | AUDIO 5-pin Terminal Block Connector | Qabbad ma 'aċċettatur awdjo stereo bilanċjat. | |
| 29 | REMOTE Contact-Closure 5-pin Terminal Block Connector | Connect to contact closure switches (by momentary contact between the desired pin and GND pin). To turn display on or off, see Pass 6: Operate KIT-401. | |
| 30 | RS-232 | CONTROL 3-pin
Terminal Block Connector |
Connect to a serial controller or PC. |
| 31 | DATA 3-pin Terminal Block Connector | Connect to a serial data source or acceptor. | |
| 32 | RELAY 3-pin Terminal Block Connector | Connections to the internal relay: normally open (NO), normally closed (NC) and common (C). Connect to devices to be controlled by relay (for example, a motorized projection screen). | |
| 33 | PoC (Power Over Cable) Switch | Set to on. | |
| 34 | Konnettur 12V DC | Connect to the supplied power adapter (if required). Follow powering instructions in Pass 5: Qabbad l-enerġija. | |
| Connect power to either this 12V power connector or to the KIT-401T terminal block (item 7). Do not connect to both! |
|||
Install KIT-401T and Mount KIT-400R
Install KIT-401T
Insert the device into the in-wall box. Note that first you need to connect the HDBT cable (and power – if powering via the transmitter) and connect the parts as shown in the illustrations below:
Verżjoni UE/UK
Verżjoni US-D
DECORA® design frames are included in US-D models. DECORA® is a registered trademark of Leviton Manufacturing Co., Inc. We recommend that you use any of the following standard 2 gang in-wall junction boxes (or their equivalent):
- US-D: 2 gang US electrical junction boxes.
- EU: 2 gang in-wall junction box, with a cut-hole diameter of 2x68mm and depth that can fit in both the device and the connected cables (DIN 49073).
- UK: 2 gang in-wall junction box (BS 4662), 135x75mm (W, H) and depth that can fit in both the device and the connected cables.
- EU/UK: 2 gang on-wall junction box (use the recommended Kramer on-wall box available at www.kramerav.com/product/KIT-401T).
Mount KIT-400R
Install KIT-400R using one of the following methods:
- Waħħal is-saqajn tal-lastku u poġġi l-unità fuq wiċċ ċatt.
- Fasten 2 brackets (included) on each side of the unit and attach them to a flat surface (see www.kramerav.com/downloads/KIT-401).
- Immonta l-unità f'rack bl-użu ta 'l-adapter tar-rack rakkomandat (ara www.kramerav.com/product/KIT-401).
Twissija:
- Kun żgur li l-ambjent (eż. Temperatura ambjentali massima u fluss ta 'arja) huwa kompatibbli għall-apparat.
- Evita tagħbija mekkanika irregolari.
- Għandha tintuża konsiderazzjoni xierqa tal-klassifikazzjonijiet tal-pjanċa tal-isem tat-tagħmir biex jiġi evitat tagħbija żejda taċ-ċirkwiti.
- L-ert affidabbli ta 'tagħmir immuntat fuq l-ixkaffa għandu jinżamm.
- L-għoli massimu tal-immuntar għall-apparat huwa ta '2 metri.
Qabbad inputs u outputs
Always switch OFF the power before connecting to your KIT-401.
Connect the audio output:
Biex tikseb distanzi ta 'estensjoni speċifikati, uża l-kejbils Kramer rakkomandati disponibbli fuq www.kramerav.com/product/KIT-401. L-użu ta 'kejbils ta' partijiet terzi jista 'jikkawża ħsara!
Wiring the RJ-45 connectors
This section defines the TP pinout, using a straight pin-to-pin cable with RJ-45 connectors. For HDBT cables, it is recommended that the cable ground shielding be connected/soldered to the connector shield.
Setting the KIT-401T OPTION DIP-switches
A switch that is down is on; a switch that is up is off. By default, all the switches are up (off). After changing a DIP switch you must power cycle the device to implement the change.
- DIP-switch 1 set to off (up).
- DIP-switch 2 set to off (up).
Audio Switching Selection
| DIP-switch 3 | DIP-switch 4 | Għażla tal-Input Awdjo | |
| Off (up) | Off (up) | Automatic – Priority selection: Embedded HDMI ” analog Audio In (high to low priority). | |
| Off (up) | On (down) | Automatic – Priority selection: Analog Audio In ” embedded HDMI (high to low priority). | |
| On (down) | Off (up) | Embedded HDMI. | |
| On (down) | On (down) | Analog Audio In. |
Qabbad il-qawwa
KIT-401 uses a PoC (Power over Cable) system, meaning that the system is powered by connecting the 12V adapter to either KIT-401T or to KIT-400R. Do not connect power to both devices. Safety Instructions (See www.kramerav.com for updated safety information) Caution:
- Għal prodotti b'terminals tar-relay u portijiet GPI \ O, jekk jogħġbok irreferi għall-klassifikazzjoni permessa għal konnessjoni esterna, li tinsab ħdejn it-terminal jew fil-Manwal tal-Utent.
- M'hemm l-ebda parti li tista 'titħaddem mill-operatur ġewwa l-unità.
Twissija:
- Failure to use PoC and power connector correctly may destroy the devices!
- Uża biss il-korda tad-dawl li hija fornuta ma 'l-unità.
- Skonnettja l-enerġija u aqla 'l-unità mill-ħajt qabel ma tinstalla.
Operate KIT-401
Operate KIT-401 via:
- B'mod remot, permezz ta 'kmandi serjali RS-232 trażmessi minn sistema ta' touch screen, PC, jew kontrollur serjali ieħor.
- Inkorporati web paġni permezz tal-Ethernet.
- Remote control switches.
| Kontroll RS-232 / Protokoll 3000 | ||||||||
| Rata Baud: | 115,200 | Parità: | Xejn | Stop Bits: | 1 | |||
| Bits tad-Dejta: | 8 | Format tal-Kmand: | ASCII | |||||
| Example: (Set the Audio out volume level to 75): #AUD-LVL 1,1,75 | ||||||||
| Parametri Ethernet default | ||||||||
| Indirizz IP: | 192.168.1.39 | Port UDP #: | 50000 | |||||
| Maskra tas-subnet: | 255.255.0.0 | Port TCP #: | 5000 | |||||
| bibien: | 0.0.0.0. | |||||||
Operating via the remote control switches
Momentarjament qabbad il-pin mixtieqa mal-pin GND biex tagħżel input:
| Isem tal-Pin | funzjoni | |
| KIT-401T | ||
| SELECT | Short press – Select the input. | Long press – Adjust the VGA phase shift. |
| REMOTE | Select the HDMI input on KIT-400R. | |
| VOL UP | Press to increase the analog audio output level. | |
| VOL DN | Press to decrease the analog audio output level. | |
| KIT-400R | ||
| TOGL | One button toggles between display on and display off (instead of using two separate buttons for on and off). Alternatively, using the KIT-400R OSD, configure toggling display on and off according to whether a switch is open or closed, for example, using an occupancy sensor. | |
| OFF | Turn off the display. | |
| ON | Ixgħel il-wiri. | |
KIT-401T
KIT-400R
Dokumenti / Riżorsi
 |
KRAMER KIT-401 Auto Switcher [pdf] Gwida għall-Utent KIT-401 Auto Switcher, KIT-401, Auto Switcher |
