KRAMER KDOCK-4-HOLDER Multiport Adapter
KDOCK-1/2/3-HOLDER
Congratulations on purchasing your Kramer KDOCK-1/2/3-HOLDER / KDOCK-4-HOLDER for safely securing KDock USB-C Hub Multiport Adapters below or on a surface. This document describes how to secure the KDOCK-1/2/3-HOLDER and the KDOCK-4-HOLDER to a surface.
Installing the KDOCK-1/2/3-HOLDER
KDOCK-1/2/3-HOLDER can be installed either under or above a surface. In this example, it is installed under a table.
To secure the KDOCK-1/2/3-HOLDER under a table:
- Insert the KDock device into the clamp, in-between the rubber pads.
- Insert a washer (supplied) and then a nut (supplied) onto each of the studs and tighten.
- Check the location under the table where you want to install the device and mark the location for the two installation screws (supplied).
- Use the two installation screws to secure the KDOCK-1/2/3-HOLDER under the table.
Installing the KDOCK-4-HOLDER
KDOCK-4-HOLDER can be installed either under or above a surface. In this example, it is installed on a table. Note that when it is installed under, the flip-up device holder cannot be used.
To secure the KDOCK-4-HOLDER on a table:
- Place the KDock-4 device on the surface, at the correct location.
- Place the KDOCK-4-HOLDER over the device.
- Insert the four screws and secure the KDOCK-4-HOLDER to the table.
Speċifikazzjonijiet tekniċi
| Kundizzjonijiet Ambjentali | Joperaw Temperatura | 0° sa +40°C (32° sa 104°F). |
| Temperatura Ħażna | -10 ° sa + 55 ° C (14 ° sa 131 ° F). | |
| umdità | 5% sa 90%, RHL mingħajr kondensazzjoni. | |
| Konformità Regolatorja | Sigurtà | DAN. |
| ambjentali | RoHs | |
| Mehmużin | materjali | Zinc-coated steel and rubber padding (for
KDOCK-1/2/3-HOLDER biss) |
| ġenerali | Dimensjonijiet Netti (W, D, H) | KDOCK-1/2/3-HOLDER: 3cm x 6.5cm x 1.9 cm (1.2″ x 2.6″ x 0.75″) Approx. |
| KDOCK-4-HOLDER: 26.2cm x 7.1cm x 2.5cm
(10.3″ x 2.8″ x 1″) Approx. |
||
| Dimensjonijiet tat-Tbaħħir (W, D, H) | KDOCK-1/2/3-HOLDER: 12.1cm x 8.2cm x 4.1cm (4.8 "x 3.2" x 1.6 ") | |
| KDOCK-4-HOLDER: 36.6cm x 21cm x 7.7 cm (14.4″ x 8.27″ x 3″) | ||
| Piż nett | KDOCK-1/2/3-HOLDER: 50g (0.11lbs) approx. KDOCK-4-HOLDER: 201g (0.44lbs) approx. |
|
| Piż Shipping | KDOCK-1/2/3-HOLDER: 90g (0.2lbs) approx.
KDOCK-4-HOLDER: 261g (0.6lbs) approx. |
Dokumenti / Riżorsi
 |
KRAMER KDOCK-4-HOLDER Multiport Adapter [pdf] Manwal ta' Istruzzjoni KDOCK-1-2-3-HOLDER, KDOCK-4-HOLDER, KDOCK-4-HOLDER Multiport Adapter, KDOCK-4-HOLDER, Multiport Adapter |
