1. Introduzzjoni
The Stander Omni Tray Table is designed to provide balance and support for individuals when sitting and standing from a couch, lift chair, or recliner. It features an oversized bamboo tray that swivels 360 degrees, offering a versatile surface for various activities. This manual provides essential information for the safe and effective use of your Omni Tray Table.
2. Informazzjoni Importanti dwar is-Sigurtà
TWISSIJA:
- Always use the Stander Omni Tray on a stable, level surface.
- Do not exceed the weight capacity of the tray (30 pounds) or handle (250 pounds).
- Keep the tray and handle in the fully extended position when not in use to prevent accidental contact.
- Keep the tray and handle clean and free of debris to maintain proper functioning.
- Do not use the Stander Omni Tray if any parts are damaged or missing.
- Always follow the instructions provided with the product for safe and proper use.
3. Kontenut tal-Pakkett
Ivverifika li l-komponenti kollha huma preżenti qabel tibda l-assemblaġġ:
- Bażi
- Tabella tat-Tray
- Assembly Hardware (screws, Allen wrench, small wrench)
Note: Additional accessories like cup holders, utensil trays, and organizers are sold separately.
4. Setup u Assemblea
The Stander Omni Tray Table requires assembly. No additional tools are required beyond those provided.
- Arma l-Bażi: Connect the base plates using the provided square tube and tighten the bolts with the Allen wrench. Ensure the base is adjusted to fit under the feet of your furniture (25 to 35 inches apart).
- Attach the Vertical Support Tube: Secure the vertical support tube to the assembled base.
- Waħħal it-Trej: Connect the "L" tube to the underside of the bamboo tray using the provided screws and tighten the bolt. Level the tray by adjusting the bolts as needed.
- Waħħal il-Manku: Secure the ergonomic standing handle to the vertical support tube.
- Pożizzjona l-Unità: Slide the assembled base plates underneath the feet of your four-legged lift chair, recliner, or couch. Ensure the furniture feet sit firmly on top of the base pads for stability.
Image: All components of the Stander Omni Tray Table laid out on a carpeted floor, including the bamboo tray, base plates, vertical support, handle, and assembly tools.
Image: The Stander Omni Tray Table correctly installed with its base plates positioned under the feet of a couch, demonstrating compatibility with various furniture types.
Installazzjoni ta' Aċċessorji Fakultattivi:
If you have purchased optional accessories, follow these steps:
- Detentur tat-tazza: Locate the pre-drilled holes on the backside of the tray. Align the cup holder and insert screws, tightening with a drill or screwdriver. Do not overtighten.
- Utensil Tray: Locate the pre-drilled holes on the backside of the tray. Align the utensil tray and insert screws, tightening with a drill or screwdriver. Do not overtighten.
- Base Organizer: Loosen the set screw on the vertical support tube and remove the plastic end cap. Slide the rubber sleeve onto the tube, then slide the organizer over the top of the rubber sleeve. Reattach the plastic end cap and reinsert the vertical support tube, tightening the set screw. The organizer can face any direction.
Video: This video demonstrates the installation tips for Omni Tray accessories, including the cup holder, utensil tray, and base organizer.
5. Istruzzjonijiet Operattivi
Using the Standing Handle:
The ergonomic safety handle provides support for sitting down and standing up. It can support up to 250 pounds. Grip the handle firmly and use it to assist your movement.
Image: A man is shown using the standing handle of the Omni Tray Table to safely push himself up from a couch, illustrating the mobility aid function.
Using the Swivel Tray Table:
The bamboo tray measures 20 by 15 inches and can support up to 30 pounds. It swivels 360 degrees, allowing you to easily pivot it into position for use or out of the way when not needed. The tray height is adjustable from 24 to 32 inches.
- Adjusting Tray Height: Locate the adjustment pins on the vertical support tube. Press the pins and slide the tray assembly up or down to your desired height. Release the pins to lock the tray in place.
- Swiveling the Tray: Gently push or pull the tray to rotate it around the vertical support.
Image: A man comfortably uses a laptop placed on the bamboo tray of the Omni Tray Table, demonstrating its use as a lap desk.
Image: The Omni Tray Table with a bottle of water and a book on its bamboo surface, highlighting its 360-degree swivel capability and 30-pound tray capacity.
Video: This video showcases the Stander Omni Tray Table being used as a work-from-home computer desk and laptop lap desk station, demonstrating its versatility.
6. Manutenzjoni
To maintain your Stander Omni Tray Table, wipe it with a dry or damp cloth as needed. Avoid using abrasive cleaners that could damage the finish.
7 Issolvi l-problemi
If you encounter any issues with your Omni Tray Table, please ensure all bolts are securely tightened and the base is properly positioned under your furniture. If problems persist, contact Stander customer support.
8. Speċifikazzjonijiet
- Dimensjonijiet tal-Prodott: 25 x 18 x 28 pulzieri
- Piż tal-oġġett: 20 liri
- Maximum Recommended Load (Handle): 250 Liri
- Maximum Recommended Load (Tray): 30 Liri
- Tray Height Adjustment: 24 sa 32 pulzier
- Support Handle Height Adjustment: 28 sa 36 pulzier
- Base Length Adjustment: 25 sa 35 pulzier
- Tip ta 'Finish: Natural Wood (Bamboo Tray)
- Assemblaġġ Meħtieġa: Iva
Image: A detailed diagram illustrating the product dimensions of the Stander Omni Tray Table, including tray size, handle height, and base length adjustments.
9. Garanzija u Appoġġ
The Stander Omni Tray Table comes with a N/a warranty. For product support, please visit the official Stander websit jew ikkuntattja lid-dipartiment tas-servizz tal-konsumatur tagħhom.
