Legrand CX³ Power Contactor 412505 User Manual

1. Introduzzjoni

This manual provides essential information for the safe and efficient installation, operation, and maintenance of the Legrand CX³ Power Contactor, model 412505. Please read this manual thoroughly before using the product and retain it for future reference.

The Legrand CX³ Power Contactor 412505 is designed for controlling electrical circuits, conforming to standard NF EN 61095. It is compatible with up to 25 A comb-shaped bus bars.

2. Informazzjoni dwar is-Sigurtà

TWISSIJA: Electrical shock hazard. Installation and maintenance should only be performed by qualified personnel. Disconnect all power before working on the contactor or connected circuits.

Dejjem segwi l-kodiċijiet elettriċi lokali u nazzjonali.
Ensure the power supply matches the contactor's specifications.
Tħaddimx il-kuntattur jekk jidher li hu bil-ħsara.
Ilbes tagħmir protettiv personali (PPE) xieraq.

3. Deskrizzjoni u Karatteristiċi tal-Prodott

The Legrand CX³ Power Contactor 412505 is a compact and reliable device for switching electrical loads. Key features include:

Mudell: 412505
Coil Voltage: 24V
Rated Current (I Max): 25 Amps
Vol ikklassifikattage: 250V (Bipolar)
Tip ta' Kuntatt: 2 Normally Open (2F)
Numru ta' Moduli: 1
Immuntar: Mount tal-Ferrovija DIN
Klassifikazzjoni tal-Protezzjoni: IP20
Materjal: Kunststoff (housing), Copper (contacts)

4. Setup u Installazzjoni

The contactor is designed for DIN rail mounting. Follow these steps for installation:

Skonnettjar tal-Enerġija: Ensure all power to the circuit is disconnected at the main breaker. Verify with a voltagtester.
Immuntar: Clip the contactor onto a standard DIN rail. Ensure it is securely fastened.
Wiring (Power Circuit):
- Connect the incoming power lines to the main terminals (e.g., L1, L2).
- Connect the load lines to the outgoing terminals (e.g., T1, T2).
- Ensure all connections are tight using the clamp tip ta 'konnettur.
Wiring (Control Circuit):
- Connect the 24V control voltage to the coil terminals (A1, A2).
- The control method is remote, typically via a switch or control system.
Verifika: Iċċekkja darbtejn il-wajers kollha għall-korrettezza u s-sigurtà qabel ma terġa' ddaħħal il-kurrent.

5. Istruzzjonijiet Operattivi

The Legrand CX³ Power Contactor 412505 operates in an ON-OFF mode, controlled by its 24V coil.

Attivazzjoni: Apply 24V DC or AC (depending on coil type, typically AC for contactors unless specified) to the coil terminals (A1 and A2). This will energize the coil, closing the main contacts and allowing power to flow to the connected load.
Diżattivazzjoni: Remove the 24V control voltage from the coil terminals. The coil will de-energize, opening the main contacts and disconnecting power from the load.
Indikatur: Some models may include a visual indicator to show the contactor's state (energized/de-energized).

Nota: The contactor is designed for remote control. There is no manual control mechanism on this specific model (as per "Coil without Manual Control").

6. Manutenzjoni

The Legrand CX³ Power Contactor 412505 is designed for minimal maintenance. However, periodic checks are recommended to ensure optimal performance and safety.

Spezzjoni Viżwali: Regularly inspect the contactor for any signs of physical damage, discoloration, or loose connections.
Issikkar tat-Terminal: Periodically check that all terminal connections are secure. Loose connections can lead to overheating and failure.
Tindif: If necessary, gently clean the exterior of the contactor with a dry, lint-free cloth. Do not use solvents or abrasive cleaners. Ensure power is disconnected before cleaning.
Ambjent Operattiv: Kun żgur li l-ambjent operattiv jibqa' fil-firxiet speċifikati tat-temperatura u l-umdità biex tevita li jintlibes qabel iż-żmien.

If any issues are observed, disconnect power and consult a qualified electrician.

7 Issolvi l-problemi

Before troubleshooting, ensure all power is disconnected. Only qualified personnel should perform troubleshooting and repairs.

Problema	Kawża Possibbli	Soluzzjoni
Il-kuntattur ma jagħtix enerġija meta l-volum tal-kontrolltage hija applikata.	Ebda kontroll voltage (24V) to coil. Incorrect wiring of control circuit. Kolja bil-ħsara.	Check 24V supply to A1/A2 terminals. Verify control circuit wiring against diagram. Replace contactor if coil is faulty.
Contactor energizes but load does not receive power.	No main power supply. Incorrect wiring of power circuit. Damaged main contacts.	Iċċekkja l-provvista tal-enerġija prinċipali u s-circuit breaker. Verify power circuit wiring against diagram. Replace contactor if contacts are faulty.
Contactor hums loudly or overheats.	Volum tal-koljatura mhux korretttage. Konnessjonijiet sfużi. Contactor operating beyond its rated capacity.	Ivverifika l-volum tal-koljatage taqbel mal-ispeċifikazzjonijiet. Issikka l-konnessjonijiet tat-terminals kollha. Ensure load current does not exceed 25A.

8. Speċifikazzjonijiet

Parametru	Valur
Numru tal-Mudell	412505
Brand	Legrand
Mod ta' Operazzjoni	ON-OFF
Current Rating (I Max)	25 Amps
Vol Operattivtage (Prinċipali)	250 Volts (Bipolar)
Vol Operattivtage (Kojl)	24 Volts
Tip ta' Kuntatt	2 Normally Open (2F)
Tip ta' Konnettur	Clamp
Tip ta' Swiċċ	Kuntattur
Tip ta' Terminal	Xafra
Materjal tad-Djar	Kunststoff
Kuntatt Materjal	Ram
Tip ta 'Ċirkwit	2-mod
Tip ta 'Immuntar	Mount tal-Ferrovija DIN
Tip ta' Attwatur	Plunger
Numru ta' Pożizzjonijiet	1
Metodu ta' Kontroll	Remote
Protokoll tal-Konnettività	Wi-Fi (Note: Refers to system integration, not inherent Wi-Fi in contactor)
Wattage (Max Load)	600 watt
Klassifikazzjoni tal-Protezzjoni Internazzjonali	IP20
Piż tal-oġġett	0.13 Kilogrammi

9. Garanzija u Appoġġ

For warranty information and technical support, please refer to the official Legrand website or contact your local Legrand distributor. Keep your purchase receipt as proof of purchase.

Legrand 412505