1. Introduzzjoni
This manual provides instructions for the safe installation, operation, and maintenance of the Leviton 8200-LW 15-Amp, 125-Volt, Hospital Grade Duplex Receptacle. Please read these instructions thoroughly before beginning installation and retain them for future reference.
Stampa 1: Quddiem view of the Leviton 8200-LW Hospital Grade Duplex Receptacle in White.
2. Informazzjoni Importanti dwar is-Sigurtà
TWISSIJA: BIEX EVITAT N-NAR, XOKK, JEW MEWT; Itfi l-Qawwa F'CIIRCUIT BREAKER JEW FUSE U Ittestja LI L-QAWWA HIJA MITFIJA QABEL IL-WIRING!
- Installation must be performed by a qualified electrician in accordance with all national and local electrical codes and regulations.
- Dejjem skonnettja l-enerġija mill-pannell tas-servizz prinċipali qabel ma taħdem fuq il-wajers elettriċi.
- Use only copper or copper-clad wire. Do not use aluminum wire with this device.
- Kun żgur li l-konnessjonijiet kollha tal-wajers huma sikuri u iżolati sew.
- Dan l-apparat huwa ddisinjat għall-użu fuq ġewwa biss.
- Teċċedix il-klassifikazzjonijiet elettriċi speċifikati tal-apparat.
3. Kontenut tal-Pakkett
The package for the Leviton 8200-LW Duplex Receptacle typically includes:
- One (1) Leviton 8200-LW 15-Amp, 125-Volt, Hospital Grade Duplex Receptacle (White)
4. Speċifikazzjonijiet tal-Prodott
| Numru tal-Mudell: | 8200-LW |
| Ampetà: | 15 Amps |
| Voltage: | 125 Volts |
| Konfigurazzjoni: | 5-15R |
| Wiring: | 3-Wire, Self-Grounding (Back and Side Wiring) |
| Poli: | 2-Arblu |
| Materjal: | Nylon (Body/Face) |
| Kulur: | Abjad |
| Approvazzjonijiet: | UL, CSA C22.2, NOM 057 |
| Tip: | Heavy Duty, Hospital Grade |
5. Setup u Installazzjoni
Għodod Meħtieġa: Screwdriver (Phillips and/or Flathead), Wire Strippers, Electrical Tape, Voltage Tester.
- Itfi l-Enerġija: Locate the circuit breaker or fuse that controls the outlet you are replacing or installing. Turn off the power and verify it is off using a voltagtester.
- Neħħi r-Reċipjent il-Qadim (jekk applikabbli): Unscrew the wall plate and then the mounting screws holding the old receptacle in the electrical box. Carefully pull the old receptacle out of the box.
- Skonnettja l-Wajers: Note the position of each wire before disconnecting. Typically:
- Wajer tar-Ram Aħdar jew Mikxuf: Wajer ta 'l-art.
- Wajer abjad: Wajer newtrali.
- Black or Red Wire: Hot (live) wire.
- Ipprepara Wajers: If necessary, strip approximately 1/2 inch (12.7 mm) of insulation from the ends of the wires. Ensure the wire ends are clean and straight.
- Qabbad il-Wajers mar-Reċipjent il-Ġdid: The Leviton 8200-LW supports both back and side wiring.
- Wajer tal-Art (Aħdar jew Ram Mikxuf): Connect to the green hexagonal ground screw.
- Wajer Newtrali (Abjad): Connect to the silver terminal screws.
- Hot Wire (Black or Red): Connect to the brass terminal screws.
For Side Wiring: Loop the wire clockwise around the screw terminal and tighten securely. Ensure no bare wire is exposed outside the terminal.
For Back Wiring: Insert the stripped wire end into the appropriate hole on the back of the receptacle and tighten the corresponding screw on the side. The V-shaped, serrated back-wiring clamps ensure superior contact.
- Reċipjent Sikur: Carefully fold the wires into the electrical box. Insert the new receptacle into the box and secure it with the mounting screws.
- Installa Pjanċa tal-Ħajt: Attach the wall plate over the receptacle.
- Irrestawra l-Enerġija: Turn the power back on at the circuit breaker or fuse.
- Test: Test the receptacle with a known working device.
6. Istruzzjonijiet Operattivi
The Leviton 8200-LW Duplex Receptacle functions as a standard electrical outlet. Once properly installed and powered, simply insert the plug of your electrical device into one of the two available outlets. Ensure the plug is fully inserted for a secure connection.
7. Manutenzjoni
- Tindif: To clean the receptacle, ensure power is off at the circuit breaker. Wipe the surface with a soft, damp drapp. Tużax tindif jew solventi li joborxu.
- Spezzjoni: Periodically inspect the receptacle for any signs of damage, such as cracks, discoloration, or loose connections. If any damage is observed, disconnect power and have the device inspected or replaced by a qualified electrician.
- "Green Dot" Marking: This hospital-grade receptacle features a permanent "Green Dot" marking on its face, indicating its compliance with hospital-grade standards for enhanced durability and reliability.
8 Issolvi l-problemi
| Problema | Kawża Possibbli | Soluzzjoni |
|---|---|---|
| L-ebda qawwa fir-reċipjent. | Circuit breaker tripped or fuse blown. Loose wiring connection. | Check and reset the circuit breaker or replace the fuse. Turn off power and check all wire connections for tightness. |
| Plug feels loose in the receptacle. | Worn receptacle contacts (unlikely for new hospital-grade). Incorrect plug type. | Ensure the plug is fully inserted. If the issue persists with multiple devices, consult a qualified electrician for inspection. |
| Receptacle is hot to the touch. | Overload on the circuit. Loose connection. Faulty device. | Immediately disconnect power. Reduce the load on the circuit. Have a qualified electrician inspect the wiring and device. |
9. Garanzija u Appoġġ
Leviton products are manufactured to the highest quality standards. For specific warranty information and customer support, please refer to the documentation included with your purchase or visit the official Leviton websit. Żomm l-irċevuta tax-xiri tiegħek bħala prova tax-xiri.
Appoġġ għall-Klijenti ta' Leviton:
- Żur l-Appoġġ ta' Leviton Websit
- Irreferi għall-informazzjoni ta' kuntatt ipprovduta fuq l-imballaġġ tal-prodott.