Max Sensor MXSA001

MAX MXSA001 315MHz TPMS Tire Pressure Sensors for Toyota Instruction Manual

Model: MXSA001 | Brand: Max Sensor

1. Pengenalan

This instruction manual provides essential information for the proper installation, operation, and maintenance of your MAX MXSA001 315MHz Tire Pressure Monitoring System (TPMS) sensors. These sensors are designed as direct replacements for various Toyota models, ensuring accurate tire pressure monitoring for enhanced safety and vehicle performance. Please read this manual thoroughly before installation and retain it for future reference.

2. Maklumat Keselamatan

  • Pemasangan Profesional Disyorkan: Installation of TPMS sensors requires specialized tools and knowledge. It is highly recommended that these sensors be installed by a qualified technician.
  • Correct Torque: Ensure valve stem nuts are tightened to the specified torque (4 Nm or 35 in-lbs) to prevent air leaks and sensor damage.
  • Pemasangan Tayar: Exercise caution during tire mounting and demounting to avoid damaging the sensor.
  • Keserasian: Verify that the sensors are compatible with your vehicle's make, model, and year before installation. Refer to the replacement OEM part numbers provided.
  • Hayat Bateri: TPMS sensors contain non-replaceable batteries. The typical lifespan is 5-7 years, depending on usage.

3. Kandungan Pakej

Setiap pakej mengandungi:

  • 4 x MAX MXSA001 315MHz TPMS Sensors
  • 4 x Silver Aluminum Valve Stems (pre-attached to sensors)
Four MAX MXSA001 TPMS sensors with silver aluminum valve stems, arranged on a white background.

Gambar 3.1: Lebihview of four MAX MXSA001 TPMS sensors.

4. Persediaan dan Pemasangan

Proper installation is crucial for the correct functioning of the TPMS. It is strongly recommended that installation be performed by a certified automotive technician.

4.1 Semakan Pra-Pemasangan

  • Confirm that the MXSA001 sensors are the correct replacement for your vehicle's OEM part numbers (e.g., 4260733021, 4260706011, 4260733011, 426070C020, 426070C010, 42607AD020, 4260704010).
  • Inspect each sensor for any visible damage before installation.

4.2 Pemasangan Sensor

  1. Keluarkan tayar dari roda.
  2. Carefully remove the old TPMS sensor and valve stem.
  3. Insert the new MAX MXSA001 sensor's valve stem through the valve hole from the inside of the rim.
  4. Secure the valve stem nut from the outside, tightening it to 4 Nm (35 in-lbs). Jangan terlalu ketat.
  5. Ensure the sensor body is properly seated and does not interfere with the tire bead during mounting.
  6. Mount the tire back onto the wheel, taking care not to damage the sensor.
  7. Tiup tayar ke tekanan yang disyorkan pengeluar.
jarak dekat view of a single MAX MXSA001 TPMS sensor, showing the black sensor body, silver valve stem, and printed specifications like 'Max.9Bar/130Psi' and '4Nm'.

Figure 4.2.1: Close-up of a single MXSA001 sensor.

sebelah view of a MAX MXSA001 TPMS sensor, highlighting the angle of the valve stem attachment to the sensor body.

Rajah 4.2.2: Sisi view of the sensor and valve stem.

4.3 Prosedur Pembelajaran Semula TPMS

After installing new TPMS sensors, your vehicle's TPMS control module must be reprogrammed or

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.