Einhell 4300345 TH-MS 2513 T Miter and Table Saw Instruction Manual

1. Pengenalan

Thank you for choosing the Einhell TH-MS 2513 T Miter and Table Saw. This versatile power tool is designed for precise cutting of wood, plastic, and non-ferrous metals, offering both miter saw and table saw functionalities. This manual provides essential information for the safe and efficient operation, setup, maintenance, and troubleshooting of your saw. Please read these instructions carefully before first use and keep them for future reference.

Gambar 1: Lebihview of the Einhell TH-MS 2513 T Miter and Table Saw.

2. Arahan Keselamatan

Sentiasa patuhi langkah keselamatan berikut untuk mengelakkan kejutan elektrik, kebakaran dan kecederaan serius:

• Baca keseluruhan manual: Understand all instructions and warnings before operating the saw.
• Wear personal protective equipment (PPE): Always wear safety glasses, hearing protection, and a dust mask. Use gloves when handling saw blades.
• Pastikan kawasan kerja bersih dan terang: Kawasan bersepah atau gelap mengundang kemalangan.
• Jangan beroperasi dalam suasana meletup: Do not use power tools in the presence of flammable liquids, gases, or dust.
• Bahan kerja selamat: Sentiasa clamp or hold the workpiece firmly to prevent movement during cutting.
• Use correct blade: Ensure the saw blade is sharp, clean, and suitable for the material being cut. Never use damaged or dull blades.
• Mengekalkan pijakan dan keseimbangan yang betul: Jangan melampaui batas.
• Putuskan kuasa: Always unplug the saw before making adjustments, changing accessories, or performing maintenance.
• Keep guards in place: Never operate the saw without all guards properly installed and functioning.
• Elakkan permulaan secara tidak sengaja: Pastikan suis berada dalam kedudukan mati sebelum memasang alat.

3. Persediaan

3.1 Membongkar dan Pemeriksaan

Carefully remove all components from the packaging. Inspect the saw for any damage that may have occurred during shipping. Do not operate the saw if any parts are damaged or missing. Contact customer support immediately.

3.2 Perhimpunan

The Einhell TH-MS 2513 T requires minimal assembly. Ensure all included components, such as the push stick and any necessary guards, are properly attached according to the diagrams in the separate assembly guide (if provided). The work table is made of lightweight and stable cast aluminum, designed for precise work.

3.3 Saw Blade Installation

1. Putuskan kuasa: Pastikan gergaji dicabut dari sumber kuasa.
2. Open blade guard: Carefully lift or open the blade guard to access the blade arbor.
3. Install blade: Place the saw blade (Ø 250 x Ø 30 x 2.8 mm, 36 teeth) onto the arbor, ensuring the rotation direction indicated on the blade matches the arrow on the saw.
4. Secure blade: Fasten the blade with the provided washer and arbor nut, tightening securely.
5. Close guard: Return the blade guard to its original position.

Figure 2: Saw blade and protective guard in miter saw configuration.

4. Arahan Operasi

4.1 Operasi Am

Before starting, ensure your workpiece is stable and properly supported. Always allow the blade to reach full speed before beginning a cut. Feed the material slowly and steadily. Never force the saw.

4.2 Miter Saw Function

The miter saw function allows for precise cross-cuts and miter cuts. Adjust the miter angle by loosening the locking knob, setting the desired angle (-45°/0°/+45°), and re-tightening the knob. For bevel cuts, adjust the saw head tilt. Ensure the workpiece is firmly against the fence.

• Kapasiti Pemotongan pada 90°: 130 x 75 mm
• Kapasiti Pemotongan pada 45°: 120 x 50 mm
• Cutting Capacity at 2 x 45° (Compound Miter): 70 x 35 mm

Figure 3: Adjusting the miter angle for precise cuts.

4.3 Table Saw Function

To use the saw as a table saw, lock the saw head in the upright position. Adjust the cutting height (0–40 mm) using the height adjustment mechanism. Use the parallel fence for rip cuts and the push stick for feeding smaller workpieces. The table surface measures 416 x 352 mm.

Figure 4: Adjusting the cutting height for table saw operation.

4.4 Pengekstrakan Habuk

The saw is equipped with a dust funnel behind the saw blade for improved sawdust collection. Connect a suitable dust extractor to the dust port to maintain a clean work environment and improve visibility during operation.

Figure 5: Dust extraction port for connecting a vacuum system.

5. Penyelenggaraan

Regular maintenance ensures the longevity and safe operation of your saw.

• Pembersihan: After each use, disconnect the saw from power and clean off sawdust and debris using a brush or compressed air. Do not use solvents that could damage plastic parts.
• Pemeriksaan Bilah: Periksa mata gergaji secara kerap untuk ketajaman, retak atau gigi yang hilang. Gantikan bilah yang kusam atau rosak dengan segera.
• Guard Functionality: Ensure all guards move freely and return to their protective positions.
• Pelinciran: Apply a light coat of machine oil to moving parts as recommended in the full manual (if applicable).
• Kord Kuasa: Check the power cord for damage. Do not use the saw if the cord is frayed or cut.

6. Penyelesaian masalah

Bahagian ini menangani isu biasa yang mungkin anda hadapi. Untuk masalah yang tidak disenaraikan di sini, hubungi sokongan pelanggan.

7. Spesifikasi Teknikal

8. Waranti dan Sokongan

8.1 Waranti

This Einhell product comes with a Waranti 2 tahun from the date of purchase. Please retain your proof of purchase for warranty claims. The warranty covers defects in material and workmanship under normal use. It does not cover damage caused by misuse, abuse, unauthorized repairs, or normal wear and tear.

8.2 Sokongan Pelanggan

For technical assistance, spare parts, or warranty inquiries, please contact Einhell customer support. You can find contact information on the official Einhell webtapak atau melalui peruncit tempatan anda.

Webtapak: www.einhell.com

Please have your model number (4300345) and serial number (if applicable) ready when contacting support.