AJAX - लोगो

ट्रान्समीटर वापरकर्ता मॅन्युअल
मार्च एक्सएनयूएमएक्स, एक्सएनयूएमएक्स अद्यतनित केले

AJAX 10306 Transmitter Wired to Wireless Detector Converter - cover

ट्रान्समीटर is a module for connecting third-party detectors to Ajax security system. It transmits alarms and warns about the activation of the external detector tamper and it is equipped with own accelerometer, which protects it from dismounting. It runs on batteries and can supply power to the connected detector.
Transmitter operates within the Ajax security system, by connecting via the protected Jeweller protocol to the hub. It is not intended to use the device in third-party systems.
Not compatible with the uartBridge or ocBridge Plus
The communication range can be up to 1,600 meters provided that there are no obstacles and the case is removed.

Transmitter is set up via a mobile application for iOS and Android based smartphones.

Buy integration module Transmitter

कार्यात्मक घटक

AJAX 10306 Transmitter Wired to Wireless Detector Converter - Functional Elements

  1. QR code with the device registration key.
  2. Batteries contacts.
  3. एलईडी सूचक.
  4. चालू / बंद बटण.
  5. Terminals for detector power supply, alarm and tamper signals.

ऑपरेशन प्रक्रिया

Transmitter is designed to connect third-party wired sensors and devices to the Ajax security system. The integration module receives information about alarms and tamper activation through the wires connected to the clamps.
Transmitter can be used to connect panic and medical buttons, indoor and outdoor motion detectors, as well as opening, vibration, breaking, re, gas, leakage and others wired detectors.
The type of alarm is indicated in the settings of the Transmitter. The text of noti cations about alarms and events of the connected device, as well as event codes transmitted to the central monitoring panel of the security company (CMS) depend on the selected type.

एकूण 5 प्रकारची उपकरणे उपलब्ध आहेत:

प्रकार चिन्ह
घुसखोरी अलार्म
आग लागली असता तिची सुचना देणारी यंत्रणा
वैद्यकीय अलार्म
पॅनिक बटण
गॅस एकाग्रता अलार्म

Transmitter has 2 pairs of wired zones: alarm and tampएर.
A separate pair of terminals ensures power supply to the external detector from the module batteries with 3.3 V.

हबला जोडत आहे

कनेक्शन सुरू करण्यापूर्वीः

  1. Following the hub instruction recommendations, install the Ajax application on your smartphone. Create an account, add the hub to the application, and create at least one room.
  2. अजॅक्स अनुप्रयोग वर जा.
  3. हब चालू करा आणि इंटरनेट कनेक्शन (इथरनेट केबल आणि / किंवा जीएसएम नेटवर्कद्वारे) तपासा.
  4. हब निशस्त केले आहे याची खात्री करा आणि मोबाइल अनुप्रयोगामध्ये त्याची स्थिती तपासून अद्यतने सुरू करत नाहीत.

केवळ प्रशासकीय विशेषाधिकार असलेले वापरकर्ते हे डिव्हाइस हबमध्ये जोडू शकतात

How to connect the Transmitter to the hub:

  1. अजॅक्स अनुप्रयोगात डिव्हाइस जोडा पर्याय निवडा.
  2. Name the device, scan/write manually the QR Code (located on the body and packaging) and select the location room.
  3. जोडा निवडा - काउंटडाउन सुरू होईल.
  4. Switch on the device (by pressing on/off button for 3 seconds).

AJAX 10306 Transmitter Wired to Wireless Detector Converter - How to connect the Transmitter to the hub

For the detection and interfacing to occur, the device should be located within the coverage area of the wireless network of the hub (at a single protected object).
डिव्हाइसवर स्विच करताना हबच्या कनेक्शनची विनंती थोड्या काळासाठी प्रसारित केली जाते.
If the connection to the Ajax hub failed, the Transmitter will switch off after 6 seconds. You may repeat the connection attempt then.
The Transmitter connected to the hub will appear in the list of devices of the hub in the application. Update of device statuses in the list depends on the device inquiry time set in the hub settings, with the default value ­ 36 seconds.

स्टेट्स

  1. साधने
  2. ट्रान्समीटर
घटक मूल्य
तापमान डिव्हाइसचे तापमान प्रोसेसरवर मोजले जाते आणि हळूहळू बदलतात
ज्वेलर सिग्नल सामर्थ्य Signal strength between the hub and the device
बॅटरी चार्ज डिव्हाइसची बॅटरी पातळी. पर्सन म्हणून प्रदर्शितtage
अजॅक्स अ‍ॅप्समध्ये बॅटरी चार्ज कसे प्रदर्शित केले जाते
झाकण टीamper terminal state
प्रविष्ट करताना विलंब, से प्रवेश करताना विलंब वेळ
सोडताना विलंब, से बाहेर पडताना विलंब वेळ
कनेक्शन Connection status between the hub and the Transmitter
नेहमी सक्रिय f active, the device is always in an armed mode
हलविल्यास सतर्क करा It turns on the Transmitter accelerometer, detecting device movement
तात्पुरती निष्क्रियता डिव्हाइस तात्पुरते निष्क्रियकरण कार्याची स्थिती दर्शविते:
नाही - डिव्हाइस सामान्यपणे कार्य करते आणि सर्व कार्यक्रम प्रसारित करते.
फक्त झाकण — the hub administrator has disabled noti the device body.
संपूर्णपणे — the device is completely excludedfrom the system operation by the hub administrator. The device does not follow system commands and does not report alarms or other events.
गजरांच्या संख्येनुसार — the device is automatically disabled by the system when the number of alarms is exceeded (speci in the settings for Devices Auto Deactivation). The feature is coned in the Ajax PRO app.
टाइमरद्वारे — the device is automatically disabled by the system when the recovery timer expires (speci Devices Auto Deactivation). The feature is
coned in the Ajax PRO app.
फर्मवेअर डिटेक्टर ई आवृत्ती
डिव्हाइस आयडी डिव्हाइस ओळख

सेटिंग्ज

  1. साधने
  2. ट्रान्समीटर
  3. सेटिंग्ज
सेटिंग मूल्य
प्रथम डिव्हाइसचे नाव, संपादित केले जाऊ शकते
खोली डिव्हाइस नियुक्त केले आहे त्या आभासी खोलीची निवड करणे
बाह्य डिटेक्टर संपर्क स्थिती Selection of the external detector normal status:
• Normally closed (NC)
• Normally opened (NO)
External Detector Type Selection of the external detector type:
• Pulse
• Bistable
Tamper स्थिती Selection of the normal tamper mod for an external detector:
• Normally closed (NC)
• Normally opened (NO)
अलार्म प्रकार Select alarm type of connected device:
• Intrusion
. आग
• Medical help
• Panic button
• Gas
The text of SMS and notivents feed, as well as the code transmitted to the security company’s console, depends on the selected type of alarms
नेहमी सक्रिय When the mode is active, the Transmitter transmits alarms even when the system is disarmed
प्रविष्ट करताना विलंब, से प्रवेश करताना विलंब वेळ निवडणे
सोडताना विलंब, से बाहेर जाण्यासाठी विलंब वेळ निवडणे
रात्री मोडमध्ये विलंब रात्री मोड वापरताना विलंब चालू केला
हलविल्यास सतर्क करा The accelerometer turning on the Transmitter to provide an alarm in the event of device movement
डिटेक्टर वीज पुरवठा Turning the power on in 3.3 V external detector:
• Disabled if disarmed
• Always disabled
• Always enabled
आर्म इन नाईट मोड सक्रिय असल्यास, रात्री मोड वापरताना डिव्हाइस सशस्त्र मोडवर स्विच करेल
Alert with a siren if an alarm is detected If active, Sirens added to the system are sirens activated if an alarm is detected
ज्वेलर सिग्नल सामर्थ्य चाचणी डिव्हाइस सिग्नल सामर्थ्य चाचणी मोडवर स्विच करते
लक्ष घालण्याची चाचणी Switches the device to the signal fade test mode (available in detectors with फर्मवेअर आवृत्ती 3.50 आणि नंतरची)
वापरकर्ता मार्गदर्शक Opens the device User Guide
तात्पुरती निष्क्रियता दोन पर्याय उपलब्ध आहेतः
संपूर्णपणे — the device will not execute system commands or run automation
scenarios. The system will ignore device alarms and not
फक्त झाकण — messages about triggering the tamper button of the device are ignored
डिव्हाइस तात्पुरते निष्क्रिय करण्याबद्दल अधिक जाणून घ्या
अलार्मची सेट संख्या ओलांडली किंवा रिकव्हरी टाइमर कालबाह्य होते तेव्हा सिस्टम देखील स्वयंचलितपणे डिव्हाइस अक्षम करू शकते.
डिव्हाइसेसच्या स्वयं निष्क्रियतेबद्दल अधिक जाणून घ्या 
डिव्हाइस जोडा डिव्हाइस हब वरून डिस्कनेक्ट करते आणि त्यातील सेटिंग्ज हटविते

Set the following parameters in the Transmitter settings:

  • The state of the external detector contact, which can be normally closed or normally open.
  • The type (mode) of the external detector that can be bistable or pulse.
  • टीamper mode, which can be normally closed or normally open.
  • The accelerometer-triggered alarm — you can turn this signal off or on.

Select the power mode for the external detector:

  • Turned off when the hub is disarmed — the module stops powering the external detector upon disarming and does not process signals from the
    ALARM terminal. When arming the detector, the power supply resumes, but the alarm signals are ignored for the
  • Always disabled — the Transmitter saves energy by turning off the power of the external detector. The signals from the ALARM terminal are processed both in the pulse and bistable modes.
  • Always active — this mode should be used if there are any problems in the “Turned off when the hub is disarmed”. When the security system is armed, signals from the ALARM terminal are processed no more than once in three minutes in the pulse mode. If the bistable mode is selected, such signals are processed instantly.

If the “Always active” operating mode is selected for the module, the external detector is powered only in the “Always active” or the “Turned off when the hub disarmed” mode, regardless of the security system status.

संकेत

कार्यक्रम संकेत
The Module is switched on and registered The LED lights up when the ON button is brie pressed.
नोंदणी अयशस्वी LED blinks for 4 seconds with an interval of 1 second, then blinks 3 times rapidly (and automatically switches OFF).
The Module is deleted from the list of hub devices LED blinks for 1 minute with an interval of 1 second, then blinks 3 times rapidly (and automatically switches OFF).
The Module has received alarm/tamper signal The LED lights up for 1 second.
बॅटरी सोडल्या जातात Smoothly lights up and goes out when the detector or tamper सक्रिय केले आहे.

कामगिरी चाचणी

अजॅक्स सुरक्षा प्रणाली कनेक्ट केलेल्या डिव्हाइसची कार्यक्षमता तपासण्यासाठी चाचण्या घेण्यास परवानगी देते.
चाचणी लगेच सुरू होत नाहीत परंतु मानक सेटिंग्ज वापरताना 36 सेकंदांच्या कालावधीत. चाचणी वेळ प्रारंभ डिटेक्टर स्कॅनिंग कालावधी (परिच्छेद वरील) च्या सेटिंग्जवर अवलंबून असते “ज्वेलर” settings in hub settings).

ज्वेलर सिग्नल सामर्थ्य चाचणी
लक्ष घालण्याची चाचणी

Connection of the Module to the wired detectorа

Location of the Transmitter determines its remoteness from the hub and presence of any obstacles between the devices hindering the radio signal transmission: walls, inserted ge-size objects located within the room.

Check the signal strength level at the installation location

If the signal level is one division, we cannot guarantee stable operation of the security system. Take possible measures to improve the quality of the signal! As a minimum, move the device — even 20 cm shift can signiove the quality of reception.
If, after moving, the device still has a low or unstable signal strength, use a . radio signal range extender ReX
The Transmitter should be encased inside the wired detector case. The Module requires a space with the following minimum dimensions: 110 × 41 × 24 mm. If the installation of the Transmitter within the detector case is impossible, then any available radiotransparent case could be used.

  1. Connect the Transmitter to the detector through the NC/NO contacts (choose the relevant setting in the application) and COM.

The maximum cable length for connecting the sensor is 150 m (24 AWG twisted pair). The value may vary when using different type of cable.

The function of the Transmitter’s terminals

AJAX 10306 Transmitter Wired to Wireless Detector Converter - The function of the Transmitter’s terminals

+ — — power supply output (3.3 V)
गजर - alarm terminals
TAMP - tamper terminals

IMPORTANT! Do not connect external power to the Transmitter’s power outputs.
This may damage the device
2. Secure the Transmitter in the case. Plastic bars are included in the installation kit. It is recommendable to install the Transmitter on them.

Do not install the Transmitter:

  • धातूच्या वस्तू आणि आरसे जवळ (ते रेडिओ सिग्नलचे संरक्षण करू शकतात आणि त्याचे क्षीणन होऊ शकतात).
  • Closer than 1 meter to a hub.

Maintenance and Battery Replacement

The device does not require maintenance when mounted in the housing of a wired sensor.

बॅटरीवर अजॅक्स डिव्हाइस किती काळ कार्य करते आणि याचा काय परिणाम होतो
बॅटरी बदलणे

टेक चष्मा

Connecting a detector ALARM and TAMPER (NO/NC) terminals
Mode for processing alarm signals from the detector Pulse or Bistable
पॉवर 3 × CR123A, 3V batteries
Capability to power the connected detector Yes, 3.3V
Protection from dismounting एक्सीलरोमीटर
फ्रीक्वेंसी बँड 868.0–868.6 MHz or 868.7 – 869.2 MHz,
depends on sales region
सुसंगतता Operates only with all Ajax , hubs and range extenders
जास्तीत जास्त आरएफ आउटपुट पॉवर 20 मेगावॅट पर्यंत
मॉड्यूलेशन जीएफएसके
संप्रेषण श्रेणी 1,600 मीटर पर्यंत (कोणतेही अडथळे अनुपस्थित)
Ping interval for the connection with the receiver 12-300 सेकंद
कार्यशील तापमान -25°C ते +50°С
ऑपरेटिंग आर्द्रता 75% पर्यंत
परिमाणे 100 × 39 × 22 मिमी
वजन 74 ग्रॅम

पूर्ण संच

  1. ट्रान्समीटर
  2. Battery CR123A — 3 pcs
  3. स्थापना किट
  4. द्रुत प्रारंभ मार्गदर्शक

हमी

“अजॅक सिस्टम्स मॅन्युफॅक्चरिंग” मर्यादित देयता कंपनीच्या उत्पादनांची हमी खरेदीनंतर 2 वर्षांसाठी वैध आहे आणि प्री-स्थापित बॅटरीवर लागू होत नाही.
डिव्हाइस योग्यरित्या कार्य करत नसल्यास, आपण सेवा देऊ नये — अर्ध्या प्रकरणांमध्ये, तांत्रिक समस्या दूरस्थपणे सोडवल्या जाऊ शकतात!

हमीचा संपूर्ण मजकूर
वापरकर्ता करार
तांत्रिक समर्थन: [ईमेल संरक्षित]

दस्तऐवज / संसाधने

AJAX 10306 Transmitter Wired to Wireless Detector Converter [पीडीएफ] वापरकर्ता मॅन्युअल
10306, Transmitter Wired to Wireless Detector Converter

एक टिप्पणी द्या

आपला ई-मेल पत्ता प्रकाशित केला जाणार नाही.