MOXA ioLogik E1500 Series I-O Ethernet Remote
Package Checklist
- 1 ioLogik E1500 series remote I/O product
- Quick installation guide (printed)
Specifications
| Input Current | 150 mA @ 24 VDC |
| Input Voltage | 12 to 48 VDC |
| Operating Temperature | -40 to 85°C (-40 to 185°F) |
Installation
I/O Wiring
DI dry contact mode
DI wet contact mode (Ch-Ch isolation)
DI wet contact PNP/NPN mode (No CH-CH isolation
DIO_DI wet contact mode (no CH-CH isolation)
DIO_DO sink mode 
Mounting and Cabling
The ioLogik E1500 can be used with both DIN rail and wall mounts. Whenmounting on a DIN rail, release the bottom mounting kit, install the ioLogik on the rail, and then restore the bottom mounting kit to fix the ioLogik to the rail. When using wall mounting, release both the upper and bottom DIN rail kits. The ioLogik E1500 has an M12 Ethernet port for connecting either a standard direct-Ethernet or crossover-Ethernet cable via a locking M12 connector.
Power and Networking
Connect the +12 to +48 VDC power line to the ioLogik E1500’s terminal block V+ terminal, and connect the ground from the power supply to the V- terminal. If an earth ground is available, connect the ground pin
LED Indicators
| Type | Color | Description |
| PWR | Green | System power in ON |
| Off | System power is OFF | |
| RDY | Green | System is ready |
| Green Blinking | Located | |
| Red | System Booting-up Error | |
| Green/Red Blinking | Safe Mode | |
| Red Blinking | Firmware upgrade (LED flashes for 3 seconds then stays red until restart) | |
| Off | System is not ready | |
| LAN | Green | 100 Mbps |
| Amber | 10 Mbps | |
| Blinking | Data Transmitting | |
| Off | Ethernet Off | |
| EXP | Green | Expansion Mode Ready |
| Red | Configuration Failure | |
| Off | Stand-alone Mode | |
| DI | Green | Channel ON |
| Off | Channel OFF | |
| DIO | Green | Channel ON |
| Off | Channel OFF |
System Configuration
Configuration via Web Console
Configuration of an ioLogik E1500 is done via the web console.
- Default IP Address: 192.168.127.254
- Subnet Mask: 255.255.255.0
Note: Be sure to configure the host PC’s IP address to the same subnet as the ioLogik E1500. For example, 192.168.127.253
ioSearch Utility
ioSearch is a search utility that helps users locate an ioLogik E1500 on the local network. The latest version of the utility can be downloaded from Moxa’s website
Load Factory Default Settings
There are three ways to restore the ioLogik E1500 to the factory default settings.
- Remove the two screws and the aluminum plate, and then press and hold the RESET button for 5 seconds.
- Right-click the specified ioLogik in the ioSearch utility and select Reset to Default.
- Select Load Factory Default from the web console.
Modbus Address Table
Refer to the user’s manual for details of the ioLogik’s Modbus address, or refer to the start address of the I/O channels in the web console under User-defined Modbus Addressing Default Address.
How to Download the Software
Step 1
Click on the following link to open the Support & Downloads search tool:
http://www.moxa.com/support/support_home.aspx?isSearchShow=1
Step 2
Type the model name in the search box or select a product from the drop down box and then click Search.
Step 3
Click the Software Packages link to download the latest software for the product
Documents / Resources
 | MOXA ioLogik E1500 Series I-O Ethernet Remote [pdf] Installation Guide ioLogik E1500 Series I-O Ethernet Remote, ioLogik E1500 Series, I-O Ethernet Remote |
