Tracks for Set up - SounDigital USA
Owner's Manual for SounDigital models including: 2000.4 EVOPS Amplifier, 2000.4, EVOPS Amplifier, Amplifier
SounDigital 2000.4 EVOPS - 2 Ohm | Amplificatori - 4 canali
SounDigital 2000.4 EVOPS - 4 Ohm | Amplificatori - 4 canali
File Info : application/pdf, 17 Pages, 4.58MB
DocumentDocumentOWNER'S MANUAL
2000.4
TABLE OF CONTENTS
Introduction ............................................................................................................................................................ 3 Package contents .............................................................................................................................................. 3 Safety instructions.............................................................................................................................................. 4 Technologies
DTM®................................................................................................................................................. 5 Ultra compact PCB................................................................................................................. 5 Robust construction............................................................................................................... 5 I-Power Supply........................................................................................................................... 5 VAS® ................................................................................................................................................. 6 Marinization with protection index IP64 ....................................................................... 6 Assembling and Disassembling the Plastic Seals ......................................................................... 7 Panels description Audio inputs and controls................................................................................................... 8 Power inputs and audio outputs ..................................................................................... 9 Installation sequence..................................................................................................................................... 10 Electrical Dimensioning ................................................................................................................................ 11 Audio inputs RCA inputs................................................................................................................................. 11 Crossover set up.............................................................................................................................................. 12 Wiring diagram Four channels wiring diagram....................................................................................... 13 Three channels wiring diagram .................................................................................... 13 Two channel wiring diagram........................................................................................... 14 Procedure for setting the gain .................................................................................................................. 14 Battery connection diagram...................................................................................................................... 15 Technical specifications Parameters ............................................................................................................................... 16 Dimensional data .................................................................................................................. 16 Additional Information ................................................................................................................................... 16
Document revision code: 1000750366-001/MAR2024
INTRODUCTION
Dear Consumer,
Congratulations, you have just acquired a SounDigital product of the highest technology and quality, so we thank you for your trust.
SounDigital products are made with raw materials of the highest quality standards, and the most modern processes, equipment and technology are used in their production.
IMPORTANT INFORMATION
On this manual you will learn about the product, its features and characteristics, in order to obtain the best result and to be able to enjoy your music with SounDigital quality and power.
Read this manual carefully and follow precisely all the information contained therein, these are very important and allow your amplifier to work optimally. If you think it is necessary, please do not hesitate to contact our technical support at the following contact:
info@soundigitalusa.com
FEATURES Resistant to moisture, water splash and dust; Compact design; Conformal coated PCB; Crossover controls variable in Low pass, High pass and Full range; High efficiency Class D; Robust construction, resistant to vibrations and bumps; IP64 rating.
PACKAGE CONTENTS 01 2000.4 EVOPS amplifier 01 Quick installation guide with warranty certificate 01 Allen wrench 2.0mm 01 Allen wrench 2.5mm 01 Allen wrench 3.0mm 01 Soundigital promotional black sticker 01 Soundigital promotional white sticker
*Merely illustrative image.
3
SAFETY INSTRUCTIONS
To avoid injury to the user or damage to the amplifier, read all safety instructions written on this manual.
The installation of this product must be done by a qualified professional. In case of any doubt, please contact our technical support;
When passing cables through metallic walls, use rubber O-rings to avoid cable cutting and short-circuits;
Before proceeding with the installation of any electric equipment on your vehicle, unplug the negative (-) terminal of the battery to avoid fires, injuries or damages; Use your sound system safely. The continuous exposure to sound pressures over 85dB may cause irreversible hearing damage;
Make sure that the chosen location for the amplifier installation does not affect the operation of the vehicle;
X
This product may reach temperatures over 60°C (140°F). Make sure it is cold before touching it;
This equipment is for use in automotive DC voltage batteries between 12.6 and 14.4 volts. Before installing the equipment, check voltage of the batteries; Do not install the amplifier in places exposed to water, dirt or humidity;
X
Choose a ventilated place to install the amplifier and avoid blocking the side ventilation windows;
Clean the amplifier periodically with brush or dry cloth to assure the thermal efficiency of the heatsink;
Be careful when making holes in the vehicle. Make sure you are not making holes in the fuel tank, brake lines or electrical cables of the vehicle; Make sure the cables are properly secured throughout the installation;
Fix the amplifier properly and firmly. Avoid fixing to metallic parts of the vehicle, as this procedure may cause ground looping (noise);
Wear gloves, safety glasses and all necessary PPE during the installation of SounDigital amplifiers.
Warning!
THIS "WARNING" SIGN ALERTS THE USER OF IMPORTANT INFO. NOT FOLLOWING THESE INSTRUCTIONS MAY CAUSE INJURIES TO THE USER OR DAMAGE TO THE EQUIPMENT.
4
TECHNOLOGIES
DYNAMIC THERMAL MANAGEMENT - DTM®
ALUMINIUM HEATSINK
CONDUCTIVE COPPER LAYER
ELECTRONIC COMPONENT
The DTM* is a dynamic thermal recovery system which always maintains a high efficiency of the amplifier by accelerating the thermal exchange of electronic components with the heatsink. *Patent required.
ULTRA COMPACT PCB An intelligent layout, with great use of the PCB area and the use of modern components with reduced structure guarantee SounDigital products a compact design, at the same time robust and with excellent thermal efficiency.
ROBUST CONSTRUCTION Thinking about the application of power sports, the product has an extremely robust assembly, both the fixing points and the layout of the PCB were designed to withstand high vibrations, bumps and impacts.
I-POWER SUPPLY SounDigital amplifiers are known for their low consumption of battery, and this feature stays on the EVOPS Line. The new I-POWER SUPPLY is even more modern, which replaces the old toroidal transformers by a new generation of "E-E" core transformers delivers efficiency above 90%*, ensuring more hours of sound without battery recharge.
*Efficiency measured at power supply only.
5
TECHNOLOGIES
HIGH SOUND WAVE ENERGY
LOW SOUND WAVE ENERGY
ABSORPTION DEVICE
VIBRATION ABSORPTION SYSTEM - VAS®
Our VAS® Technology reduces all impact caused by vibration on the electronic circuit board. This can include road vibration and even vibration caused by sound waves, increasing the reliability of our amplifiers.
REDUCED SIZE
8.4"
5.8"
The technology used in our amplifiers bring both high performance and power a compact chassis, providing flexible installation solutions for vehicles with limited space.
FULL RANGE The 2000.4 EVOPS amplifier is a versatile product that cover the entire audible frequency range, any type of loudspeaker or music program.
MARINIZATION WITH PROTECTION INDEX IP64 The product is protected against ingress of dust particles and water droplets from all sides, beyound that, the PCB receives a conformal coating treatment to protect the components from moisture.
6
ASSEMBLING AND DISASSEMBLING THE PLASTIC SEALS
DISASSEMBLING THE PLASTICS SEALS
1
2
3
1. Squeeze the assembled Flexible Plastics Seals; 2. Pull out the Plastics Seals.
*Merely illustrative images.
ASSEMBLING THE PLASTICS SEALS
1
2
3
RCA Plastic Seal
Potentiometer Plastic Seal
Slide switch Plastic Seal
1. Hold the disassebled Flexible Plastics Seals and fit them in their specific housing; 2. Each connector has its specific Plastic Seal; 3. Make sure the Flexible Plastics Seals are perfectly fitted.
*Merely illustrative images.
7
PANELS DESCRIPTION Audio inputs and controls
11 1 3 9 6 5
7 8 10 4 2
1
CH1/CH2
2
CH3/CH4
3
CH1/CH2
4
CH3/CH4
5
CH1
6
CH2
7
CH3
8
CH4
9
CH1/CH2
10
CH3/CH4
11
Blue
Variable crossover control -- 45Hz ~ 850Hz Crossover switch
High Pass -- Full -- Low Pass
Audio inputs -- RCA connectors
Variable Gain Control "POWER ON" LED indicator
8
PANELS DESCRIPTION Power inputs and audio outputs
16 15 18 17 19 20 21 22 14 13 12
12
-
13
-
14
-
15
CH1
16
CH1
17
CH2
18
CH2
19
CH3
20
CH3
21
CH4
22
CH4
Negative power supply connector (GND) Remote power supply connector (REM) Positive power supply connector (+12VDC)
Positive speaker connector (+) Negative speaker connector (-) Negative speaker connector (-) Positive speaker connector (+) Negative speaker connector (-) Positive speaker connector (+) Positive speaker connector (+) Negative speaker connector (-)
9
INSTALLATION SEQUENCE
BEFORE PROCEEDING WITH THE INSTALLATION, UNPLUG THE NEGATIVE TERMINAL FROM ALL OF THE BATTERIES, TO AVOID FIRE, DAMAGE TO THE AMPLIFIER AND THE Warning! USER HIMSELF. Ø Mount the amplifier in such a way you have access to the connectors; Ø Install the power cables in the vehicle/vessel properly, starting from the battery to the fuse holder or circuit breaker, use the cable with the appropriate size. Make all connections, install fuse holders or circuit breakers, but without placing the fuses or with the circuit breakers in the "OFF" position;
THE MAXIMUM DISTANCE FOR THE INSTALLATION OF THE FUSE/CIRCUIT BREAKER IS 12 INCHES (30cm) AWAY FROM THE BATTERY. Warning! Ø Connect the power cables in to the amplifier, observing the polarity. Connect all the positive cables (+) from the fuse holder or circuit breaker to the positive conector of the amplifier and all the negative power cables from the batteries to the negative connector of the amplifier; Ø The ground cable must be as short as possible and must be connected to the negative connector of battery or vehicle chassis in case of metallic chassis;
Remove the paint between the terminal
and chassis
Ø Install the signal input cables in a proper way, distant from the power cables; Ø Connect the RCA cables to the head unit and amplifiers; Ø Install the audio output cables with the appropriate section, distant from the power and
audio input cables; Ø Connect the audio output cables to the amplifier and speakers respecting the positive (+)
and negative (-) polarities; Ø Install the remote cable with the power cables, using 1.5mm² (15 AWG) cable or thicker; Ø Connect the remote power cable to the amplifier's "REM" terminal at the main unit's remote
power output; Ø Before powering the system, verify all the connections and make sure there are no
mistakes or short-circuits on the power and ground cables; Ø Reconnect the ground of the batteries; Ø Check if the head unit is turned off and then place the fuses in the fuse holders or switch the
circuit breakers on; Ø Turn on the main unit and the amplifier will turn on the "POWER ON" LED indicating that it is
in operation.
Minimum recommended installation distance Warning! between amplifiers*.
1.18in (30mm)
X
*For installations with more than one amplifier, second unit not included. Merely illustrative images.
10
ELECTRICAL DIMENSIONING AND AUDIO INPUTS
ELECTRICAL DIMENSIONING For proper operation of your SounDigital amplifier, you need the proper dimensioning of the electrical system and the cables used.
The table below shows the minimum section of GND cables, +12VDC cables and speaker output cables according to the power generated by the amplifier.
2000 WRMS
POWER CABLE (+12VDC) GROUND CABLE (GND)
SPEAKER CABLE
21mm² (4 AWG) 2mm² (14 AWG)
We recommend the use of only OFC (Oxygen Free Copper) cables on the installation of our products.
Copper-clad aluminum wire (CCAW) must not be used.
AUDIO INPUTS RCA inputs
REMOTE
11
CROSSOVER SET UP
"HP" Set variable control in High Pass function. "F" Set variable control in Full Range function; "LP" Set variable control in Low Pass function;
Ø Change the switch to "F" position (Full Range) - All frequencies will be reproduced as shown in the graph;
dB
0dB -3dB
5Hz
22kHz Hz
Ø Change the switch to "HP" position - Set in the variable control between 45Hz and 850Hz ("A") where you want to perform the high pass cut filter;
dB
A
0dB -3dB
-12dB
c/2 c
High
High
Pass
Pass
Hz
Ø Change the switch to "LP" position - Set in the variable control between 45Hz and 850Hz ("B") where you want to perform the low pass cut filter.
dB
B
0dB -3dB
-12dB
c c*2
Low
Low
Pass Pass
Hz
12
WIRING DIAGRAM 4 CHANNELS WIRING DIAGRAM
All RCA inputs must be connected for the amplifier to work properly.
+12V
REMOTE GND
See "AUDIO INPUTS" on page 11.
(PER CHANNEL) (PER CHANNEL)
Minimum impedance
Model
Per channel
2000.4 EVOPS 4
2
2000.4 EVOPS 2
1
Bridge 4 2
In case of connections with more than one battery, see the installation diagram on page 15.
FUSE FUSE
+12V +12V
3 CHANNELS WIRING DIAGRAM
All RCA inputs must be connected for the amplifier to work properly.
+12V
REMOTE GND
See "AUDIO INPUTS" on page 11.
(PER CHANNEL) (BRIDGE)
Minimum impedance
Model
Per channel
2000.4 EVOPS 4
2
2000.4 EVOPS 2
1
Bridge 4 2
In case of connections with more than one battery, see the installation diagram on page 15.
FUSE FUSE
+12V +12V
13
WIRING DIAGRAM / GAIN SETTING 2 CHANNELS WIRING DIAGRAM
All RCA inputs must be connected for the amplifier to work properly.
Minimum impedance
Model
Per channel
2000.4 EVOPS 4
2
2000.4 EVOPS 2
1
Bridge 4 2
In case of connections with more than one battery, see the installation diagram on page 15.
+12V
REMOTE GND
+12V +12V
FUSE FUSE
See "AUDIO INPUTS" on page 11.
(BRIDGE)
GAIN SETTING Necessary equipament: Ø Digital AC voltmeter; Ø Media with sine wave test tone 60Hz
recorded at 0db; Ø Screwdriver 1/8" ( for gain setting). Set up procedure: Ø This procedure is the same for both
gain controls; Ø Turn the gain control all the way down;
Ø Disconnect the output cables from the amplifier outputs;
Ø Turn off all processing (bass, treble, loudness, EQ, etc.);
Ø Set the audio player volume to 3/4 of full volume;
Ø Set the audio player fader control to center position (left and right fader controls);
Ø Set the crossover selector switch in "F";
Ø Use a 60 Hz sine wave;
Ø Connect the AC voltmeter to the speaker output connectors of the amplifier. Make sure you test the voltage at the correct connectors (+ and );
Ø Increase the gain control until the target voltage is observed with the voltmeter (see the chart below);
Ø Once you have adjusted the amplifier to the correct voltage output, turn off the source unit and reconnect the speaker(s).
MODEL
2000.4
2
2000.4
4
STEREO / POWER
1 / 500W 2 / 500W
BRIDGE / POWER
2 / 1000W 4 / 1000W
STEREO OUTPUT VOLTAGE
22.4V 31.6V
BRIDGE OUTPUT VOLTAGE
44.8V 63.2V
Download the tracks for set up in https://soundigitalusa.com/tracks-for-set-up/
14
BATTERY CONNECTION DIAGRAM
When necessary the association of one or more battery banks to supply the necessary current to the amplifier, it is recommended to use batteries of the same brand, model, and if possible the same manufacturing lot so that the system has the maximum performance. For an ideal energy performance, we recommend that all batteries be connected to positive and negative busbars and the busbars connected to the amplifier, as shown in the diagram below:
It is mandatory to install the fuse at a maximum distance of 12 inches from the battery.
1 FUSE
BUSBAR
2
FUSE FUSE
All cables, positive and negative, connected from the battery to the busbar must be the same length. Likewise the cables connected from the busbar to the amplifier.
BUSBAR
FUSE
Battery connections without the use of a busbar, as shown in the example below, must be avoided. This setting decreases the efficiency of supplying power to the system.
FUSE
1
It is mandatory to install the fuse at a maximum distance of 12 inches from the battery.
2
FUSE
3
*Merely illustrative image.
15
TECHNICAL SPECS
PARAMETERS
Power RMS @ 4** Power RMS @ 2**
2000.4
2
4 x 217W
4 x 330W
Power RMS @ 1** Power RMS (Bridge) @ 4**
4 x 500W 2 x 660W
Power RMS (Bridge) @ 2**
2 x 1000W
Frequency Response (-3dB)
5Hz ~ 22kHz
Low Pass filter (12dB/octave)
45Hz ~ 850Hz
High Pass filter (12dB/octave)
45Hz ~ 850Hz
Operating Voltage
9V ~ 16V
SNR
90dB
Input Sensitivity (RCA)
0.2 ~ 4V
Input Sensitivity (High Level input)
N/A
Current Draw (music)
85A
Current Draw (max.)
171A
Total Efficiency
81%
Damping Factor (@100Hz nominal impedance)
200
Power Cable
21mm² (4 AWG)
Speaker Cable
2mm² (14 AWG)
Remote Cable
1.5mm² (15 AWG)
Recommended Fuse* (music)
100A
Recommended Battery (minimum)
100Ah
*It is mandatory to install the fuse at a maximum distance of 12 inches from the battery. **Power at 14.4V @ 60Hz with a maximum THD of 1%.
2000.4
4
4 x 330W
4 x 500W
N/A
2 x 1000W
N/A
5Hz ~ 22kHz
45Hz ~ 850Hz
45Hz ~ 850Hz
9V ~ 16V
90dB
0.2 ~ 4V
N/A
85A
171A
81%
200
21mm² (4 AWG)
2mm² (14 AWG)
1.5mm² (15 AWG)
100A
100Ah
**POWER RATING ACCORDING TO CTA-2006 INDUSTRY STANDARDS.
DIMENSIONAL DATA
214.0mm (8.4") 202.0mm (7.9")
149.0mm (5.8") 129.0mm (5.0")
62.0mm (2.4")
Net Weight Gross Weight
1.80 kg (3.96 lb) 2.02 kg (4.45 lb)
ADDITIONAL INFORMATION
The values presented are based on measurements performed in SounDigital's laboratories. All the equipment used in the assays, tests, measurements and gauging of the technical parameters of SounDigital products were calibrated in certified laboratories, thus ensuring the performance and standard of excellence of the developed products.
The Manufacturing Process may present variations, and the electronic components may also present changes in values in relation to their nominal parameters. Thus, causing small differences between measurements taken. Small variations in the values presented and divulged by SounDigital are recognized.
Updates of information made in this document will always be published and made available for consumer consultation, free of charge, on the brand's websites. The user is advised to search for the manual in its latest version when necessary.
The images presented in this document are representative and merely illustrative; therefore, they do not necessarily correspond to the actual product/model.
16
Document revision code: 1000750366-001/MAR2024