XtremepowerUS 12-inch Sand Filter Pump System (Model 75110-V) Instruction Manual

1. Вовед

This manual provides detailed instructions for the safe and efficient installation, operation, and maintenance of your XtremepowerUS 12-inch Sand Filter Pump System. Please read this manual thoroughly before attempting to install or operate the system. Keep this manual for future reference.

Figure 1: XtremepowerUS 12-inch Sand Filter Pump System in operation.

Безбедносни мерки на претпазливост

• Секогаш исклучувајте го напојувањето пред да вршите било каков сервис или одржување.
• Ensure the system is installed on a level surface.
• Do not operate the pump dry. Ensure it is primed with water before starting.
• Држете ги децата подалеку од пумпата и системот за филтрирање за време на работата.
• This pump is not for use/sale in California.

2. Содржина на пакетот

Проверете дали сите компоненти наведени подолу се вклучени во вашиот пакет. Доколку недостасуваат или се оштетени некои делови, ве молиме контактирајте ја службата за корисници.

Слика 2: Сите компоненти вклучени во пакетот.

• Sand Filter Tank (12-inch)
• 0.75 HP Pool Pump
• 4-насочен повеќепортен вентил
• Манометар
• System Tray / Mounting Base
• Адаптери за црева
• Црева и Clamps
• Прирачник

3. Спецификации

Key technical specifications for the XtremepowerUS 12-inch Sand Filter Pump System:

Слика 3: Димензии на производот.

4. Поставување и инсталација

Follow these steps carefully to assemble and install your sand filter pump system. Refer to the video for visual guidance.

4.1 Склопување на филтер

1. Install Drain Nozzle: Place an O-ring onto the long side of the filter drain nozzle. Route the nozzle from inside the filter barrel and push it out through the bottom drain hole. Place another O-ring and secure it with the nut from outside the barrel. Insert an O-ring into the drain hole nozzle cap and screw it onto the nozzle.
2. Position Filter Assembly: Place the filter assembly inside the filter barrel. Position the funnel on top of the filter assembly, ensuring it is correctly inserted and centered within the barrel.
3. Наполнете со филтер медиум: Fill the filter barrel with your chosen filter media (filter balls or sand) according to recommended guidelines. Remove the funnel after filling.
4. Install 4-Way Valve: Place an O-ring onto the 4-way valve. Position the valve on the upper part of the filter, ensuring the top of the filter assembly is properly inserted into the bottom of the valve. Ensure the valve pump opening aligns with the filter stand groove and the waste opening is oriented towards the drain nozzle. Secure the valve in place with the locking ring. Place the square nut on one side of each locking ring and tighten.
5. Инсталирајте манометар: Secure the pressure gauge with plumber's tape. Remove the pressure gauge covering screw from the valve and screw the pressure gauge onto the valve.

4.2 Инсталација на пумпа

1. Position Pump on Base: Place the pump on top of the system tray (mounting base), aligning it with all four screw holes.
2. Безбедна основа за монтирање: Flip the mounting base over and insert all four nuts into the mounting spaces. Carefully flip the mounting base back.
3. Fasten Pump: Place the bolts into the screw holes and tighten all four bolts with a Phillips screwdriver to secure the pump to the base.
4. Install Pump Adapters: Put O-rings on the hose adapters and screw the hose adapters onto the pump outlet and inlet.

4.3 Инсталација на црево

Осигурете се дека сите црева clamps are securely tightened to prevent leaks. Verify O-rings are correctly seated.

1. Filter to Pump Connection: Ставете црево clamp on the hose adapter from the valve opening marked 'PUMP'. Connect a hose to this adapter and then to the pump's inlet hose adapter. Tighten both hose clamps.
2. Pool Return to Valve Connection: Connect the hose from the pool's return inlet to the hose adapter from the valve opening marked 'POOL'. Ensure the O-ring on the hose adapter is not displaced during this process. Tighten the hose clamp.
3. Pool Main Drain to Pump Connection: Connect the hose from the pool's main drain to the hose adapter on the pump's outlet. Tighten the hose clamp.

5. Операција

The 4-way multi-port valve allows for different operational modes. Always ensure the pump is OFF before changing valve settings.

Figure 4: Multi-port valve settings.

Valve Modes:

• Филтрација: This is the standard operating mode. Water is pumped from the pool, filtered through the sand media, and returned to the pool.
• Повратно перење: Used to clean the filter media. Water flow is reversed, flushing trapped debris out through the waste port. Perform backwash when the pressure gauge reading is 8-10 PSI above the clean filter reading.
• Исплакнете: After backwashing, this mode settles the filter media and removes any remaining dirt from the filter lines before returning to filtration mode.
• Отпад: Drains water directly from the pool, bypassing the filter. Useful for lowering pool water level or vacuuming heavy debris directly to waste.
• Рециркулирајте: Circulates pool water without filtering.
• Зима: Used for winterizing the system.

6. Одржување

Редовното одржување обезбедува оптимални перформанси и долготрајност на вашиот систем за филтрирање.

6.1 Повторно перење

Backwash the filter when the pressure gauge indicates a rise of 8-10 PSI above its normal clean operating pressure. This typically means the filter media is saturated with debris.

1. Исклучете ја пумпата.
2. Set the multi-port valve to 'BACKWASH'.
3. Turn on the pump and run until the water from the waste port runs clear (typically 1-2 minutes).
4. Исклучете ја пумпата.
5. Set the multi-port valve to 'RINSE'.
6. Вклучете ја пумпата и оставете ја да работи 30-60 секунди.
7. Исклучете ја пумпата.
8. Set the multi-port valve back to 'FILTRATION'.
9. Turn on the pump to resume normal operation.

6.2 Cleaning the Pump Strainer Basket

The pump's strainer basket should be checked and cleaned regularly to prevent debris from entering the pump impeller.

Figure 5: Pump strainer basket.

1. Исклучете ја пумпата и затворете ги сите потребни вентили за да спречите проток на вода.
2. Unscrew the clear lid of the strainer basket.
3. Извадете ја корпата и испразнете ги сите собрани остатоци.
4. Rinse the basket thoroughly.
5. Replace the basket and securely screw the lid back on. Ensure the O-ring is properly seated to prevent air leaks.
6. Open valves and prime the pump if necessary before restarting.

6.3 Замена на филтер медиум

Sand filter media typically lasts 3-5 years, depending on usage and water quality. Filter balls may require more frequent cleaning or replacement.

1. Исклучете ја пумпата и исклучете го напојувањето.
2. Drain the filter tank completely.
3. Remove the multi-port valve.
4. Carefully remove the old filter media.
5. Rinse the inside of the tank.
6. Add new filter media, ensuring the standpipe is centered.
7. Reassemble the valve and reconnect all hoses.
8. Perform a backwash and rinse cycle before resuming normal filtration.

7 Смена на проблеми

This section addresses common issues you might encounter with your sand filter pump system.

8. Гаранција и поддршка

For warranty information or technical support, please refer to the warranty card included with your product or visit the XtremepowerUS official webлокација. Чувајте ја сметката за купување како доказ за какви било гаранциски побарувања.