Milesight VS373 Radar Fall Detection Sensor
Specifications
- Model: VS373
- Power Supply: Type-C Power Adapter (5V, 3A)
- Installation Location: Ceiling, center of the room
- Default Settings:
- Wi-Fi SSID: Fall Detection_XXXXXX
- Wi-Fi IP: 192.168.1.1
- Username: admin
- Password: pwd123456
Product Usage Instructions
Packing List:
Ensure all components are included in the package:
- VS373 Sensor
- Type-C Power Adapter
- Ceiling Mounting Kits
- Spring Clips
- Silicone Plugs
- DO Wiring
Hardware Introduction:
The device includes various components such as the Reset Button, LED Indicator, Quick Start Guide, Warranty Card, Multi-function Button Radar, and Buzzer.
Button Description:
Functions and actions related to button operations:
| Function | Action & Description |
|---|---|
| Turn On/Off Wi-Fi | Short press the Multi-function button once |
| Radar Reset to Factory Default | Press and hold the reset button for 10 seconds |
| Fall Alarm Stop Alarm | Press and hold the reset button for 6~9 seconds |
| Device abnormality | Radar anomaly; WiFi anomaly |
Power Supply:
The device is powered by a Type-C Power Adapter (5V, 3A).
Installation:
Follow these steps for proper installation:
- Install the device on the ceiling at the center of the room.
- If using DO wiring, connect it to the device and pass it through the side wire hole.
- Ensure the device is flat and stable to avoid tilting.
- Avoid installing near ceiling fans or chandeliers.
Access the Web GUI:
Use the provided default settings to access the web GUI via Wi-Fi.
Packing List
Hardware Introduction
Button Description
Power Supply
Powered by Type-C Power Adapter (5V, 3A)
Installation
Installation Location: For optimal installation, place the device on the ceiling at the center of the room. The long side of the device should align with the longer dimension of the room, while the short side should align with the shorter dimension of the room.
Ceiling Mount
Step 1：
Note: If you need to hide the power cord into the ceiling, drill another wire hole.
Step 2：
Note: If the DO wiring is going to be used, please connect the DO wiring to the device, then pass through the side wire hole.
Step 3：
Step 4：
Cutout Mount
Step 1：
Step 2：
Step 3：
Note: If the DO wiring is going to be used, please connect the DO wiring to the device, then pass through the side wire hole.
Step 4：
Step 5：
Installation Note：
- Ensure the installation location of the device is flat and stable to avoid tilting or instability.
- Avoid installing the device near ceiling fans or chandeliers.
- Minimize the accumulation of cabinets or clutter within the device’s detection range, and avoid the presence of large metal surfaces, mirrors, or other reflective objects nearby.
- The room size, installation height, and detection height should be accurately measured using tools such as a rangefinder or tape measure before setting.
Access the Web GUI
- VS373 provides a user-friendly web GUI for configuration access via Wi-Fi. The default settings are as below:
- Wi-Fi SSID: Fall Detection_XXXXXX (can be found on the device label)
- Wi-Fi IP: 192.168.1.1
- Enable the Wireless Network Connection on your computer, search for the corresponding Wi-Fi SSID to connect it, then type 192.168.1.1 to access the web GUI.
- Username: admin
- Password: pwd123456
FCC Statement
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and.
- This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
- Milesight IoT Co., Ltd.
- www.milesight.com
- Xiamen Milesight IoT Co., Ltd.
- Add:Building C09, Software Park Phase III, Xiamen 361024,Fujian,China
FAQs
Q: What should I do if the LED Indicator is blinking quickly?
A: If the LED blinks quickly, it indicates radar anomaly or WiFi anomaly. Try resetting the device by pressing and holding the reset button for 6 to 9 seconds.
Q: How can I access the web GUI for configuration?
A: Enable Wireless Network Connection on your computer, connect to the device’s Wi-Fi SSID, and access 192.168.1.1 in a web browser. Use ‘admin’ as the username and ‘pwd123456’ as the password.
Documents / Resources
 |
Milesight VS373 Radar Fall Detection Sensor [pdf] User Guide VS373, VS373 Radar Fall Detection Sensor, VS373, Radar Fall Detection Sensor, Fall Detection Sensor, Detection Sensor |