1. Kupu Whakataki
Mauruuru koe mo te hokoasing the COVERY LED Digital Desk Clock. This clock features a clear, large digit display, automatic and manual brightness adjustment, real-time room temperature display, and dual alarms. This manual provides instructions for proper setup and operation to ensure optimal performance.
2. Ihirangi mokete
- COVERY LED Digital Desk Clock (Model ACD-330)
- USB Power Cable (Note: Power adapter not included)
- CR2032 Battery (pre-installed for memory backup)
- Pukapuka Kaiwhakamahi
3. Hua Neke Atuview
Familiarize yourself with the clock's display and control buttons.
Whakaahua: Rear view of the clock with labeled buttons for Dimming, F/C/Sec, 12h/24h, Alarm 1 Set, and Alarm 2 Set. Dimensions are also indicated.
Control Buttons (Rear Panel):
- '+' Button (Dimming): Short press for manual dimming. Long press for auto dimming.
- '-' Button (F/C/Sec): Short press to switch between Fahrenheit (°F) and Celsius (°C) for temperature display, or to display seconds.
- 'SET' Button (12h/24h): Short press to toggle 12-hour/24-hour format. Long press to set date and time.
- 'Alarm 1 Set' Button: Short press to toggle Alarm 1 on/off. Long press to set Alarm 1 time.
- 'Alarm 2 Set' Button: Short press to toggle Alarm 2 on/off. Long press to set Alarm 2 time.
4. Tatūnga
- Hononga Mana: Connect the provided USB power cable to the clock's USB port. Plug the other end into a USB power adapter (not included) or a powered USB port. The clock will power on and display the default time.
- Battery Installation (Backup): A CR2032 button cell battery is pre-installed to maintain time settings during power outages. Ensure the plastic pull tab is removed if present.
- Whakanoho: Place the clock on a flat surface using its stand or mount it on a wall using the integrated keyhole slot on the back.
5. Nga Tohutohu Whakahaere
5.1 Tautuhi Wā me te Rā
- Long press the 'SET' button until the year flashes. Use the '+' or '-' buttons to adjust the year.
- Press 'SET' again to move to month, then day, hour, and minute. Adjust each value using '+' or '-'.
- After setting the minutes, press 'SET' to confirm and exit time setting mode.
Image: The clock displaying time in both 12-hour (AM/PM) and 24-hour formats.
5.2 Te Whakatakoto i ngā Pūoho (Pūoho 1 me te Pūoho 2)
- Long press the 'Alarm 1 Set' button (or 'Alarm 2 Set' button) until the hour flashes. Use '+' or '-' to adjust the hour.
- Press the respective Alarm Set button again to move to minutes. Adjust using '+' or '-'.
- Press the Alarm Set button again to confirm and exit alarm setting mode.
- Short press the 'Alarm 1 Set' (or 'Alarm 2 Set') button to toggle the alarm on or off. An alarm icon will appear on the display when active.
Image: The digital clock on a bedside table, showing the time and an active alarm icon, indicating the alarm function.
5.3 Whakaritenga Tirohanga
- Maamaa-a-ringa: Short press the '+' button to cycle through 4 levels of brightness (20%, 60%, 100%, OFF).
- Pouri Aunoa: Long press the '+' button to activate the automatic dimming function. The clock will adjust brightness based on ambient light. Long press again to deactivate.
Image: Four clocks demonstrating various brightness levels: 20%, 60%, 100%, and off, illustrating the dimmer function.
5.4 Whakaaturanga Pawera
- The clock displays the room temperature by default.
- Short press the '-' button to switch between Fahrenheit (°F) and Celsius (°C).
- Pressing '-' again will display seconds instead of temperature. Cycle through to return to temperature display.
Image: Three clocks displaying time alongside temperature in Fahrenheit, then seconds, and finally temperature in Celsius.
6. Tiaki
- Horoia te mata o te karaka ki te kakahu ngohengohe, maroke. Kaua e whakamahi i ngā kaihoroi whakakoi, i ngā whakarewa rānei.
- A ape i te tuku i te karaka ki te wera nui, te ra tika, te makuku nui ranei.
- If the clock is not used for an extended period, disconnect it from power. The backup battery will preserve settings.
7. Te Raru
| Raruraru | Take pea | Rongoā |
|---|---|---|
| Kare te karaka i te hiko. | No power supply or faulty USB cable/adapter. | Me whakarite kei te hono pai te taura USB, ā, kei te mahi te urutau hiko. Whakamātauria tētahi atu tauranga USB, urutau rānei. |
| He atarua rawa, he kanapa rawa ranei te whakaaturanga. | Me whakatikatika te tautuhinga kanapa. | Short press the '+' button to adjust manual brightness. Long press '+' to toggle auto-dimming. |
| Kare e tangi te whakaoho. | Ko te whakaoho kaore i te whakahohe, i te he ranei te whakatakotoranga. | Short press the 'Alarm Set' button to ensure the alarm icon is displayed. Verify the alarm time is set correctly. |
| Time/Date is incorrect after power loss. | Backup battery is depleted or not installed correctly. | Ensure the CR2032 backup battery is correctly installed and has sufficient charge. Replace if necessary. |
8. Whakatakotoranga
- Tauira: ACD-330
- Ahu: 6.4"W x 2.8"H
- Momo Whakaatu: Mamati Mamati
- Puna Mana: USB (DC 5V/1A recommended)
- Pūhiko Pūrua: 1 x CR2032 (included)
- Nga waahanga motuhake: Dual Alarms, 4-Level Brightness Adjustment (Manual/Auto), Indoor Temperature (°F/°C), 12/24 Hour Format, Snooze Function.
- Rauemi: Kirihou
- Tae: Mā
9. Pūtāhui me te Tautoko
This product comes with a limited warranty. For warranty details or technical support, please refer to the contact information provided with your purchase or visit the official COVERY webpae.
For further assistance, you may contact COVERY customer service.