Wampler CATACOMBS

WampPukapuka Kaiwhakamahi mō te Reverb me te Delay Pedal a ler Catacombs

Model: CATACOMBS

Kupu Whakataki

Ko te Wampler Catacombs is a programmable, all-in-one delay and reverb pedal designed to provide a wide range of time-based effects for musicians. This manual provides essential information for setting up, operating, maintaining, and troubleshooting your Catacombs pedal.

Ka mutu te huaview

The Catacombs pedal integrates 11 popular delay and reverb sounds into a single, intuitive unit. It features studio-quality 48 kHz sampling rate with 24-bit audio conversion, 8 onboard preset locations, and MIDI compatibility for up to 128 total presets.

Wampler Catacombs Reverb and Delay Pedal front view

Whakaahua 1: Mua view o te Wampler Catacombs pedal, showing controls for delay and reverb effects, input/output jacks, and footswitches.

Wampler Catacombs Reverb and Delay Pedal angled view

Whakaahua 2: Koki view o te Wampler Catacombs pedal, highlighting its compact design and various control knobs.

Tatūnga

Nga Whakaritenga Mana

Ko te Wampler Catacombs pedal requires a standard 9V DC power supply (not included) with a center-negative barrel connector. Ensure the power supply provides sufficient current for optimal performance.

Connecting Your Pedal

  1. Honoa to taputapu (hei tauira, kita) ki te MONO IN or STEREO IN Jack i te taha matau o te pedal ma te whakamahi i te taura taputapu 1/4-inihi paerewa.
  2. Honoa te MONO KI WAHO or TINO Jack i te taha maui o te pedal ki tou ampte pētera pānga panuku, te pētera whakapūmau rānei.
  3. Honoa te pūtake hiko 9V DC ki te 9V DC Jack tāuru.
  4. For MIDI control, connect a MIDI cable to the MIDI whakauru.

Nga Tohutohu Whakahaere

Nga Mana Whakahaereview

  • Delay Type Knob: Selects between various delay types including Tape, SPC, FTE, BBD, ANLG, and DIGI.
  • Reverb Type Knob: Selects between reverb types such as SHMR (Shimmer), PLT (Plate), SPR (Spring), ROOM, and HALL.
  • Time/Shimmer Knob: Adjusts the delay time or shimmer intensity depending on the selected effect.
  • Feedback/Decay Knob: Controls the number of delay repeats or the reverb decay time.
  • Mod Rate Knob: Adjusts the modulation rate for effects with modulation.
  • Delay Tone Knob: Shapes the tone of the delay repeats.
  • Reverb Tone Knob: Shapes the tone of the reverb effect.
  • Bypass/ALT Footswitch: Toggles the effect on/off. Hold to access alternate functions (ALT mode).
  • Preset/Save Footswitch: Cycles through presets. Hold to save current settings to a preset location.
  • Tap Tempo Wawaewae: Taps in the desired delay tempo.

Tiaki me te Maharahara Tatūkē

The Catacombs pedal allows for 8 onboard preset locations. To save a preset, adjust the knobs to your desired sound, then press and hold the Preset/Save footswitch until the indicator lights confirm the save. To recall a preset, short press the Preset/Save footswitch to cycle through the saved locations.

Alternate Functions (ALT Mode)

Some knobs have alternate functions accessible by holding the Bypass/ALT footswitch. When in ALT mode, the indicator light will change (e.g., from blue to red as noted in some user feedback), allowing you to adjust secondary parameters. Release the footswitch to return to normal operation.

Te tiaki

To ensure the longevity and optimal performance of your Wampler Catacombs pedal, follow these maintenance guidelines:

  • Keep the pedal clean by wiping it with a soft, dry cloth. Avoid abrasive cleaners or solvents.
  • Whakaorangia te hikoi ki te waahi makariri, maroke atu i te ra tika me te wera nui.
  • Momotuhia te hiko ina kore e whakamahia mō ngā wā roa.
  • Tirohia nga hononga taura katoa mo te pai kia mau.

Raparongoā

RaruraruTake peaRongoā
Kāore he tangi ina pēhia te pētera.Incorrect power supply, faulty cables, incorrect input/output connections.Verify power supply is 9V DC center-negative. Check all instrument cables. Ensure input is connected to IN and output to OUT.
Effect is too subtle or too extreme.Knobs are set incorrectly, or in ALT mode unintentionally.Adjust the relevant control knobs (Time, Feedback, Tone). Check if the pedal is in ALT mode and adjust accordingly.
Cannot save or recall presets.Incorrect footswitch operation.Ensure you are holding the Preset/Save footswitch long enough to save. For recalling, use short presses.
Haruru, ngunguru rānei.Ko te porowhita o te whenua, te tuku hiko hapa, te pokanoa.Use an isolated power supply. Try different cables. Ensure proper grounding of all equipment.

Whakatakotoranga

  • Tauira: CATACOMBS
  • Ahu: 7.25 x 5.7 x 3.75 inihi
  • Taumaha Tūemi: 1.39 pauna
  • Puna Hiko: Corded Electric (9V DC, center-negative, power supply not included)
  • Hōputu Tohu: Tauritenga
  • Painga Putanga Ororongo: Whakaroa, Reverb
  • Sampreiti ling: 48 kHz
  • Audio Bit Depth: 24-bit
  • Tatūkē: 8 onboard, 128 via MIDI
  • Manufacture Location: Designed and Built in the USA

Pūtāhui me te Tautoko

Wampler Pedals products are designed and built to high standards. For warranty information and technical support, please refer to the official Wampte Pedals webpaetukutuku, whakapā atu ranei ki ta raatau ratonga kaihoko. Puritia to tohu hoko mo nga kereme whakamana.

Mo etahi atu awhina, tirohia te Wampler Store on Amazon.

© 2025 Wampler Pedals. All rights reserved.