OWON CM2100 Digital AC/DC Clamp Tohutohu mita

Kupu Whakataki

This manual provides essential information for the safe and effective operation of your OWON CM2100 Digital AC/DC Clamp Meter. Please read this manual thoroughly before use and retain it for future reference. The CM2100 is a portable, true RMS clamp mita i hangaia mō te ine i te iahiko AC/DC, te hiko AC/DCtage, resistance, capacitance, diode, and non-contact voltage (NCV).

Nga korero haumaru

WHAKATŪPATO: Hei karo i te ru hiko, i ngā whara rānei, pānuihia, kia mārama hoki ki ngā mōhiohio haumaru katoa i mua i te whakamahinga o tēnei hua.

• Kia mau tonu ki nga ture haumaru o te rohe me te motu.
• Kaua e whakamahi i te mita ki te ahua kua pakaru, ki te kino ranei te whakamaarama.
• Kaua e tono nui ake i te reiti voltage, kua tohuhia ki te mita, i waenga i nga pito, i waenga ranei i tetahi tauranga me te whenua whenua.
• Kia tupato ki te mahi tahi me te voltagkei runga ake i te 30V AC RMS, te tihi 42V, te 60V DC ranei. Ko enei voltaghe morearea ohorere.
• Tangohia ngā taura whakamātautau mai i te mita i mua i te whakatuwheratanga i te taupoki pākahiko.
• Me whakarite kei te tūranga tika te pana mahi mō te inenga e mahia ana.
• Kaua e mahi i te mita huri noa i te hau pahū, te kohu, te puehu ranei.
• Always use appropriate personal protective equipment (PPE).

Ka mutu te huaview me nga Waehanga

Familiarize yourself with the various parts of your CM2100 clamp meter before operation.

Atahanga: Detailed diagram of the OWON CM2100 clamp meter, highlighting its key components such as the NCV sensor, pincher head trigger, function selection knob, DCA reset/BLE button, function selector, NCV light, LCD display, numerical lock/backlight switch, capacity/resistance/voltage/frequency/diode/ON-OFF input jack, and common-end jack. Dimensions are also indicated.

• Pūoko NCV: Ka kitea te oro kore-pātage.
• Pincher Head Trigger: Ka whakatuwhera me te kati i te clamp kauae.
• Puka Whiriwhiri Taumahi: Rotates to select different measurement modes (e.g., V~, V=, A~, A=, Ω, NCV, VFC, Hz%).
• DCA Reset/BLE Button: Used for DC current zeroing and Bluetooth (BLE) activation on compatible models (CM2100B).
• Kaitohu Taumahi: Toggles between specific functions within a mode (e.g., AC/DC voltage, resistance/capacitance).
• Rama NCV: Illuminates to indicate non-contact voltage kitenga.
• Whakaaturanga LCD: E whakaatu ana i ngā pānui ine, ngā waeine, me ngā tohu.
• Numerical Lock/Backlight Switch: Locks the current reading (HOLD) and activates the display backlight.
• Ngā Jack Tāuru: Mō te hono i ngā taura whakamātautau mō te voltage, resistance, capacitance, diode, and continuity measurements.
• Common-End Jack: The negative (-) input for test leads.

He aha kei roto i te Pouaka

Upon opening the package, verify that all items listed below are present and undamaged.

Atahanga: Contents of the OWON CM2100 package, including the CM2100 clamp meter, a pair of multimeter test leads (red and black), a small bolt driver, a quick guide, and a soft carrying bag.

1. OWON CM2100 Clamp mita
2. Multimeter Test Leads (Red and Black)
3. Bolt Driver (for battery compartment)
4. Aratohu Tere
5. Puke Kawea ngawari

Tatūnga

Tāuta Pūhiko

1. Me mohio kua whakawetohia te mita.
2. Rapua te wahanga pākahiko kei muri o te mita.
3. Use the provided bolt driver to loosen the screw securing the battery cover.
4. Tangohia te taupoki pākahiko.
5. Insert the Lithium Metal battery (included) according to the polarity markings inside the compartment.
6. Whakakapihia te taupoki puhiko ka whakakikīhia te tīwiri.

Hia Tuatahi

Rotate the function selection knob from OFF to any measurement function to power on the meter. The LCD display will illuminate.

Nga Tohutohu Whakahaere

Kōwhiringa Mahi

Rotate the central knob to select the desired measurement function. The meter features an automatic range for most measurements, simplifying operation.

Atahanga: Ka mutuview of the OWON CM2100's multiple measurement functions, including Resistance (Ω), NCV, VFC, HOLD, ON/OFF (continuity), LCD, Capacitance, Diode, Overload Protection, Low Battery Alert, Buzzing Prompt, and True RMS. It also highlights the 20000 counts, auto range, AC/DC voltage, and AC/DC current measurement capabilities.

Aratau Ine

• AC/DC Current Measurement (A~ / A=):

  Rotate the knob to the 'A~' or 'A=' position. Press the trigger to open the clamp jaws and enclose a single conductor. Ensure the conductor is centered within the jaws for accurate readings. The display will show the current value. For DC current, press the DCA Reset button to zero the reading before measurement.

• AC / DC Voltage Measurement (V~ / V=):

  Insert the red test lead into the VΩHz input jack and the black test lead into the COM jack. Rotate the knob to 'V~' for AC voltage or 'V=' for DC voltage. Connect the test leads in parallel to the circuit or component to be measured. The display will show the voltage uara.
• Resistance Measurement (Ω):

  Insert test leads as for voltage. Rotate the knob to the 'Ω' position. Connect the test leads across the component. The display will show the resistance value in Ohms (Ω).

• Te ine inenga:

  Insert test leads as for voltage. Rotate the knob to the 'Ω' position and use the Function Selector button to cycle to capacitance mode (usually indicated by 'nF', 'µF'). Connect the test leads across the capacitor. The display will show the capacitance value.

• Whakamatau Whakatautau:

  Insert test leads as for voltage. Rotate the knob to the 'Ω' position and use the Function Selector button to cycle to diode test mode (indicated by a diode symbol). Connect the red lead to the anode and the black lead to the cathode of the diode. The display will show the forward voltage maturuturu.
• Whakamātautau Tonu:

  Insert test leads as for voltage. Rotate the knob to the 'Ω' position and use the Function Selector button to cycle to continuity mode (indicated by a buzzer symbol). If the resistance is below a certain threshold, the buzzer will sound, indicating continuity.

• Kore-Whakapā Voltage (NCV) Rapunga:

  Rotate the knob to the 'NCV' position. Bring the NCV sensor (top part of the clamp meter) close to an AC voltage source. The NCV light will illuminate, and an audible beep will sound, with increasing frequency as the meter gets closer to the voltage puna.

• VFC (Variable Frequency Drive) Measurement:

  Rotate the knob to the 'VFC' position. This mode is designed for measuring AC voltage and frequency of variable frequency drives, providing more stable readings in such environments.
• Frequency (Hz%) Measurement:

  Rotate the knob to the 'Hz%' position. This mode measures the frequency of AC signals. Connect test leads as for voltage measurement. The display will show the frequency in Hertz (Hz).

Nga Mahi Apiti

• Taumahi HOLD: Press the HOLD button (often combined with backlight) to freeze the current reading on the display. Press again to release.
• Maama Whakamuri: Press and hold the HOLD/Backlight button to activate the display backlight for better visibility in low-light conditions. Press and hold again to turn off.
• RMS Pono: The CM2100 is a True RMS meter, meaning it accurately measures AC voltage and current for both sinusoidal and non-sinusoidal waveforms.
• Bluetooth Communication (CM2100B model only): If you have the CM2100B model, activate Bluetooth by pressing the BLE button. This allows remote data viewing and instrument control via a compatible smartphone application.

Atahanga: Examples of the OWON CM2100 clamp meter in use, demonstrating capacitance measurement for maintenance, NCV (Non-Contact Voltage) inductive measurement, circuit board resistance measurement, and diode measurement.

Te tiaki

Te horoi

Horoia te mita ki te pānuitangaamp kakahu me te horoi ngawari. Kaua e whakamahi i te abrasive me te whakarewa. Kia noho kore he paru me te makuku nga pito whakauru.

Whakakapinga Pūhiko

When the low battery indicator appears on the display, replace the battery promptly to ensure accurate measurements. Refer to the "Battery Installation" section under Setup for instructions.

Rokiroki

If the meter is not used for an extended period, remove the battery to prevent leakage. Store the meter in a cool, dry place, away from direct sunlight and extreme temperatures.

Raparongoā

Whakatakotoranga

Pūtāhui me te Tautoko

OWON products are designed for reliability and performance. For warranty information or technical support, please refer to the official OWON webte waahi, whakapā atu ranei ki to kaitoha o to rohe. Puritia to riirii hoko hei tohu mo te hoko mo nga kereme whakamana.

Mo etahi atu awhina, ka toro atu koe ki te OWON Store on Amazon.