NICE WAY WM006G Control Module Instruction Manual

1. Kupu Whakataki

The NICE WAY WM006G is a radio transmitter module designed for controlling up to 6 roller shutters or groups of shutters. It provides open, stop, and close functionality. This module is an integral part of the NICEWAY system, ensuring compatibility with NICE radio receivers and control logics A01/A02 operating at a frequency of 433.92 MHz.

This manual provides essential information for the proper setup, operation, and maintenance of your WM006G control module.

Figure 1: The WM006G module can be integrated into various NICEWAY accessory housings for different applications.

Figure 2: Illustration of the NICEWAY system, demonstrating wireless communication between the WM006G module, a central receiver, and other compatible accessories.

2. Tatūnga me te Tauhoa

Before operating your WM006G module, it must be correctly set up and paired with your NICE radio receivers. The module is powered by a single CR2032 battery.

2.1 Tāuta Pūhiko

1. Whakatuwheratia te casing of the WM006G module. Refer to the product diagrams for guidance on accessing the battery compartment.
2. Insert one CR2032 lithium coin cell battery, ensuring the correct polarity (+/-) as indicated inside the compartment.
3. Close the module casing haumaru.

2.2 Pairing with Receivers

The WM006G module needs to be programmed or paired with each NICE radio receiver it will control. The exact pairing procedure may vary depending on your specific NICE receiver model. Generally, the process involves activating a programming mode on the receiver and then transmitting a signal from the WM006G module.

• Using an Existing Remote: If you have an existing, working NICE remote control, you can often use it to quickly program the new WM006G module. This typically involves pressing a sequence of buttons on the old remote, followed by a button on the new WM006G module. This process may need to be repeated for each individual roller shutter or group.
• Direct Pairing: For new installations or if an existing remote is unavailable, consult the instruction manual for your specific NICE radio receiver (e.g., A01/A02 logic, FLOR, or ONE series receivers) for detailed pairing instructions. This usually involves pressing a programming button on the receiver itself.

Tuhipoka: Successful pairing is indicated by a specific response from the receiver, such as a motor movement or an LED flash.

3. Operating the WM006G Module

The WM006G module allows control of up to six individual roller shutters or six groups of shutters using its intuitive button layout.

Figure 3: Layout of the WM006G control module, showing the numbered selection buttons and control functions.

3.1 Nga Mahi Mana Taketake

1. Select Shutter/Group: Press the numbered button (1 mā 6) corresponding to the specific roller shutter or group of shutters you wish to control.
2. Open Shutter: Pehia te Runga (▲) button to open the selected shutter or group.
3. Close Shutter: Pehia te Raro (▼) button to close the selected shutter or group.
4. Stop Shutter: Pehia te Kati button to halt the selected shutter or group at any desired position during movement.

4. Tiaki

Regular maintenance ensures the longevity and optimal performance of your WM006G module.

4.1 Whakakapinga Pūhiko

The WM006G module is powered by one CR2032 lithium coin cell battery. When the module's response becomes inconsistent or it ceases to function, the battery likely needs replacement.

• Open the module casing as described in the "Battery Installation" section.
• Tangohia te pākahiko CR2032 tawhito.
• Insert a new CR2032 battery, observing the correct polarity.
• Katia te casing haumaru.
• Te tukunga: Makahia nga pākahiko kua whakamahia kia rite ki nga ture o te rohe.

4.2 Te horoi

To clean the module, use a soft, dry cloth. Avoid using abrasive cleaners, solvents, or excessive moisture, as these can damage the electronic components or the casing.

5. Te Raru

If you encounter issues with your WM006G module, try the following troubleshooting steps:

• Kōwae Kāore i te Whakautu:
  • Takina Pūhiko: Ensure the CR2032 battery is correctly installed and not depleted. Replace it with a new one if necessary.
  • Reprogramming/Pairing: If the module loses connection or is a new installation, it may need to be re-paired with your NICE radio receivers. Refer to the "Setup and Pairing" section and your receiver's manual.
  • Awhe: Verify that the module is within the operational range (35-200 meters) of the receiver. Obstructions like thick walls or metal structures can reduce range.
  • pokanoa: Other radio devices operating on similar frequencies (433.92 MHz) might cause interference. Try operating the module away from such devices.
• Shutter Responds Intermittently:
  • This could indicate a weak battery. Replace the CR2032 battery.
  • Check for potential sources of radio interference.
• Shutter Moves in Wrong Direction:
  • This is typically a programming issue with the receiver or motor. Consult your receiver's manual for instructions on reversing motor direction or re-programming limits.

If these steps do not resolve the issue, contact NICE customer support or a qualified technician.

6. Whakatakotoranga

7. Pūtāhui me te Tautoko

Warranty information for the NICE WAY WM006G module is typically provided with your purchase documentation or can be obtained directly from the manufacturer, NICE. Please retain your proof of purchase for warranty claims.

For technical support, further assistance, or to inquire about spare parts, please contact NICE customer service or your authorized dealer. Contact details can usually be found on the manufacturer's official webpae, i roto ranei i to putunga hua.