Smart Leak Protector
The Smart leak protector monitors and controls your water supply and senses water leakage. It is an ideal automation solution for water supply control in apartments, houses,s or for your irrigation system.
FIVORIANA ALOHA
Standard package contains:
Smart Leak Protector, water leakage sensor, two mounting plugs with ascrew M6X45mm, Installation Manual
When ordering accessories, the package may also contain any of: 24VDC power supply adapter, water meter with pulse reader, water valve with electric coil
INSTALLATION
- To prevent electrical shock and/or equipment damage, do not connect the power supply adapter to electrical power before completing installation or during maintenance.
- Be aware that even if the power supply adapter is not connected to the main electrical power, some voltage mety mijanona ao anaty tariby - alohan'ny hirosoana amin'ny fametrahana azy dia alao antoka fa tsy misy voltage dia eo amin'ny wiring.
- Mitandrema fanampiny mba tsy hamerenana tsy nahy ny fitaovana mandritra ny fametrahana.
- Install the device exactly according to this installation manual – see attached are installation diagrams (on the opposite side):
1. Connect the water meter, water valve, water sensor, and power supply. Put aside the two blind covers and decoration frame. Carefully lift the upper part of Smart Leak Protector housing to reveal the terminal for wire connections, marked with + – signs. Use the knife to make a hole in the cable fitting at the bottom of the Smart Leak protector housing.
Connect the water meter, water valve, and leak detector to Qubino Smart Leak Protector as indicated in the picture:
2. Finally connect the 24VDC power supply as indicated. Make sure that you pull the cables through the cable fitting.
3. Close the Smart Leak Protector housing. Make sure that the cabling inside the housing is not clamped by the housing. Place the Qubino module on the right-hand side of the box as indicated in picture 2. Make sure the Qubino module antenna is placed next to the housing wall as indicated in picture 2 (see arrow 1). Place the two blind covers as indicated in the picture. Place the blind cover with the label on it in the rightest position (see arrow 2). Press the blinds until you hear a click.
4. Mark the position of the mounting holes Place the Smart Leak Protector housing in a suitable place on the wall. Use a pencil to mark the position of the mounting holes. See picture 3.
5. Drill the mounting holes and install the Smart Leak Protector Use the 6mm drill. Drill the holes at markings 45mm deep. Insert fixings into holes, place the Smart Leak Protector over the holes and insert the two screws. Tighten the screws all the way. See picture 4.
6. Atsofohy ao anaty fivoahan'ny herinaratra ny adaptatera herinaratra.
7. Power on the Smart Leak Protector Press the Power-on button on Smart Leak Protector. The white light indicates the Smart Leak Protector is turned on. See picture5.
8. Include the device into the Z-Wave network See Z-Wave inclusion section and picture 6. - If you have a connected water valve*, press the water valve push button of Smart Leak Protector. Check that the water valve is closed (the water flow meter is steady) and that the button light indicator is ON. Press the button again and verify that the water valve is open (the water flow meter is turning) and that the button light indicator is OFF.
*NOTE: your water valve must be of the “Normally Open Valve” type. See your water valve manual for details.
INFORMATION SAFETY
Loza amin'ny herinaratra!
Installation of this device requires a great degree of skill and may be performed only by a licensed and qualified electrician. Please keep inmind that even when the device is turned off, the voltage dia mety mbola misy ao amin'ny faran'ny fitaovana.
Fanamarihana!
Do not connect the device to loads exceeding the recommended values.
Connect the device exactly as shown in the provided diagrams. Improper wiring may be dangerous and result in equipment damage.
Z-WAVE fampidirana
SMARTSTART INCLUSION
- Scan QR code on device label and add S2 DSK to Provisioning List in the gateway (hub)
- Ampifandraiso amin'ny famatsiana herinaratra ny fitaovana
- Inclusion will be initiated automatically within a few seconds of connection to the power supply and the device will automatically enroll in your network (when the device is excluded and connected to the power supply it automatically enters the LEARN MODE state).
FANAMBARANA MANOLANA
- Alefaso ny fomba manampy/manala eo amin'ny vavahadin-tserananao Z-Wave (habe)
- Ampifandraiso amin'ny famatsiana herinaratra ny fitaovana
- Press the water valve button on Smart Leak Detector 3 times within 3 seconds (1 click per second). The device has to get an On/Off signal 3 times,.
- A new device will appear on your dashboard
Fanamarihana: In case of S2 Security inclusion a dialog will appear prompting you to enter the corresponding PIN number (5 underlined digits) that are written on the module label and the label inserted in the packaging (check the exampny sary).
ZAVA-DEHIBE: The PIN code must not be lost
Z-WAVE EXCLUSION/RESET
Z-WAVE EXCLUSION
- Ampifandraiso amin'ny famatsiana herinaratra ny fitaovana
- Ataovy azo antoka fa ao anatin'ny elanelana mivantana amin'ny vavahadin'ny Z-Wave-nao ny fitaovana na mampiasa lavitra Z-Wave tànana mba hanaovana fanilikilihana.
- Alefaso ny fomba fanilihana amin'ny vavahadin'ny Z-Wave-nao (habe)
- Press the water valve button on Smart Leak Detector 3 times within 3 seconds
- The device will be excluded from your network, but any custom configuration parameters will not be erased.
NOTE1: LEARN MODE state allows the device to receive network information from the controller.
NOTE2: After the device is excluded you should wait 30seconds before performing re-inclusion.
Famerenana amin'ny laoniny
- Ampifandraiso amin'ny famatsiana herinaratra ny fitaovana
- Within the first minute the device is connected to the power supply, press the water valve button on Smart Leak Detector 5 times within 5 seconds
By resetting the device, all custom parameters previously set on the device will return to their default values, and a node ID will be deleted.
Use this reset procedure only when the gateway (hub) is missing or otherwise inoperable.
FANAMARIHANA: See the extended manual for custom settings and parameters available for this device.
FANAMARIHANA
Z-Wave wireless communication is not always 100% reliable. This device should not be used in situations in which life and/or valuables are solely dependent on its functioning. If the device is not recognized by your gateway (hub) or shows up incorrectly, you may need to change the device type manually and make sure your gateway (hub) supports ZWave
Plus devices. Contact us for help before returning the product:http://qubino.com/support/#email
FAMPITANDREMANA
Aza ariana ho toy ny fako monisipaly tsy voasoroka ny fitaovana elektrika, ampiasao trano fanangonam-bokatra mitokana. Mifandraisa amin'ny governemanta eo an-toerana raha mila fanazavana momba ny rafitra fanangonana misy. Raha ariana eny amin'ny fanariam-pako na fanariam-pako ny fitaovana elektrika, dia mety hivarina any anaty rano ny akora mampidi-doza ka hiditra ao amin'ny rojo sakafo, hanimba ny fahasalamanao sy ny fahasalamanao. Rehefa manolo ny fitaovana taloha amin'ny vaovao ny mpivarotra dia adidy ara-dalàna ny mamerina ny fitaovanao taloha mba hariana maimaim-poana.
ELECTRICAL DIAGRAM (24 VDC
Fanamarihana momba ny diagram:
| + - Q I1 I2 I3 TS |
Positive lead (+VDC) The negative lead (-VDC) Output for the electrical device (load) no. 1 The input used for the water-leak detector The input used for the water meter pulse reader Input for push-button switch Input for temperature sensor (not used in Smart Leak Protector) |
FAMPITANDREMANA:
The durability of the device depends on the applied load. For resistive loads (light bulbs, etc.) and 10A current consumption of an electrical device, the product’s lifespan exceeds 100,000 toggles.
TECHNICAL SPECIFICATIONS
| Power famatsiana | 24-30VDC |
| The rated load current of DC output (resistive load)* | 1 X 10A / 24VDC |
| Output circuit herin'ny DC Output (resistive entana) | 240W (24VDC) |
| Toby fiasa | -10 — +40°C (14 — 104°F) |
| Z-Wave isan-karazany miasa | hatramin'ny 30 m anatiny (98 ft) |
| Dimensions (WxHxD) (fonosana) | 398x220x95 mm / 15,67 × 8,66 × 3,74 in |
| Weight standard package | 619g / 21,83 oz |
| ‘Electricity consumption | 0,4W |
| ara | fampitàna |
| F-Wave Repeater | Eny |
| Tarika matetika miasa (s) | Z-wave (868Mhz EU frequency) |
| Maximum radio-frequency power jrancmittorl in frarinonry hand(c) | <2,5mw |
*In case of loads other than resistive loads, please pay attention to the value of cos φ. If necessary, connect loads less powerful than what they’re rated for – this applies to all motor loads. Max current for cos φ=0,4 is 3A at 24VDC L/R=7ms.
KAODY SY FREQUENCY COMMANDE
ZMNHDXY – X, Y values define product version per region. Please check the online extended manual or catalog for the right version.
Get a real Qubino Z-Wave bible! How-to install, use cases, user manual, illustrations, and more. Scan the QR code/follow the product link below:
https://qubino.com/products/smart-leakage-protector/
https://qubino.com/products/flush-onoff-thermostat2/
FANAMBARANA Eoropeanina tsorina
Hereby, Gap d.o.o. Nova Gorica declares that the radio equipment type Smart Leak Protector Relay is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:
http://qubino.com/products/smart-leak-protector.
Fanambarana fanarahan-dalàna FCC (any Etazonia ihany no mihatra):
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/ TV technician for help.
CE declaration of compliance is available on the product page under www.qubino.com.
This user manual is subject to change and improvement without prior notice.
Manaova Nova Gorica
Ulica Klementa Juga 007, 5250 Solkan, Slovenia
E-mail: [email voaaro] ; Tel: +386 5 335 95 00
Web: www.qubino.com; Daty: 24.03.2021; V 1.0
Documents / Loharano
 |
Qubino 09285 Smart Leak Protector [pdf] Torolàlana fametrahana 09285, Smart Leak Protector |
