Holy Stone HS260 Drone Instructions for Use

1.0 Disclaimer & Warning

Before using the Holy Stone HS260 drone, carefully read this Disclaimer & Warning and Safety Guidelines. This product is not recommended for individuals under 14 years of age. By using this product, you agree to assume responsibility for your conduct and any resulting damages. Use the product only for its intended purposes and in accordance with local laws, regulations, and Holy Stone guidelines. Holy Stone is not responsible for personal injury, property damage, legal disputes, or adverse events caused by violating safety instructions or other factors.

2.0 Safety Guidelines

2.1 Check Before Use

• Ensure the drone is configured carefully for safe operation.
• Verify drone and transmitter batteries are clean, undamaged, and fully charged.
• Confirm all propellers are undamaged and correctly installed.
• Perform a thorough pre-flight check for cracks, wear, and battery effectiveness. Do not use if problems are found.

2.2 Flight Environment

Fly in open areas, maintain line of sight, and stay below 328 feet (100 m). Avoid obstacles, crowds, high voltage power lines, trees, airports, and bodies of water. Do not fly near strong electromagnetic sources (power lines, base stations) as they may affect the compass. Do not use in adverse weather conditions (rain, snow, fog, wind).

2.3 Operation Requirements

• Do not use to follow moving vehicles.
• Turn off motors only in emergencies.
• Return drone when battery is low.
• Do not operate under the influence of alcohol, drugs, fatigue, or physical discomfort.
• Maintain distance from the drone to avoid ear damage from noise.
• Stay away from rotating propellers and motors.
• Do not fly in prohibited areas or close to others to respect privacy.

2.4 Use of Battery

• Install batteries with correct orientation.
• Avoid short circuits; do not crush or squeeze batteries to prevent fire/explosion.
• Do not mix new and old batteries.
• Dispose of used batteries carefully and recycle.
• Do not expose dead batteries to heat or fire.
• Remove batteries for extended storage.
• Use only the provided USB charging cable.
• Do not connect battery directly to wall outlets or car cigarette lighters.
• Do not disassemble or modify the battery.
• Discontinue use if battery emits odor, generates heat, discolors, deforms, or appears abnormal.
• Do not pierce battery casing.
• Charge batteries on a fireproof surface away from combustible materials.
• Do not immerse battery in water.
• Do not solder battery terminals.
• Keep batteries out of reach of children and pets.
• Do not short-circuit battery terminals.

Li-Po Battery Disposal & Recycling: Do not dispose of with household trash. Contact local environmental agencies or recycling centers for proper disposal.

3.0 Maintenance

• Clean with a soft cloth after each use.
• Avoid prolonged direct sunlight exposure and heat buildup.
• The device is not waterproof; do not submerge or expose to water.
• Regularly check charging plug and accessories for damage. Do not use or charge if damaged.

4.0 Package Contents

• Drone
• Transmitter
• Drone Battery
• Spare Propeller
• USB Charging Cable
• Screwdriver
• Instructions For Use Manual

5.0 Drone Details

The Holy Stone HS260 drone features Propellers (A & B), an HD Camera, an Optical Flow Lens, and a Drone Battery compartment.

6.0 Transmitter Details

The transmitter includes a Phone Holder, Take Photo button, Record Video button, Left Joystick (for ascend/descend, rotate left/right in Mode 2), Right Joystick (for forward/backward, fly left/right in Mode 2), Power Switch, One Key Takeoff/Landing button, Speed Switch, Folded Handle, Headless Mode button, and a Battery Cover. It requires 4×AAA batteries (not included). Ensure correct polarity when installing batteries.

7.0 Mode Switch

7.1 MODE 2 (Default Setting)

Left Joystick controls Ascend/Descend and Rotate Left/Right. Right Joystick controls Forward/Backward and Fly Left/Right.

7.2 MODE 1

To enter Mode 1, turn on the transmitter while holding the "Record Video" button until powered on. Left Joystick controls Forward/Backward and Rotate Left/Right. Right Joystick controls Ascend/Descend and Fly Left/Right.

8.0 Installation

8.1 Propellers

Connect each propeller to its corresponding motor shaft (A or B) and secure with a screw. Ensure the correct "A" or "B" propeller is installed on the correct motor shaft for flight.

8.2 Drone Battery

Installation: Remove the black insulation gasket. Push the battery into the drone compartment until a click is heard, indicating it's firmly installed. A loose battery can affect flight safety. Removal: Press the lock button on the battery and pull it back from the fuselage.

9.0 Charging

When the drone battery is low, indicator lights flash. Remove the battery, connect the USB charging cable to the battery charging interface, and plug into a USB charging port on a power bank or USB adapter (5V/2.0A). The indicator light on the cable turns on during charging and off when fully charged. Charging time is approximately 60 minutes. Refer to the "Use of Battery" section in "Safety Guidelines" before charging.

10.0 Operation Guide

10.1 Download APP

Scan the QR code for the HS FPV V4 app on App Store™ (iOS) or Google Play™ Store (Android). Required OS: iOS 9.0+ / Android 5.0+.

10.2 Connect to Wi-Fi

Turn off Bluetooth, Mobile Data, and VPN. Go to phone's Wi-Fi settings, search for the drone's Wi-Fi (e.g., HolyStone-******), and connect. Enter the HS FPV V4 app. The drone's Wi-Fi network does not provide internet access.

10.3 Pairing

1. Long press the drone's power switch until indicator lights flash.
2. Place the drone on a flat, level surface with the head facing forward.
3. Short press the transmitter's power switch until its indicator light flashes.
4. Push the left joystick up then down to pair. Lights on both drone and transmitter will turn solid upon successful pairing.

10.4 Calibrating the Gyro

Simultaneously push the left and right joysticks to the bottom right corner. Drone indicator lights will blink then turn solid, indicating calibration is complete. Calibrate after pairing and after any crash for stable flight.

10.5 Unlocking the Motor

Before takeoff, simultaneously push the left joystick to the bottom right corner and the right joystick to the bottom left corner. The motors will rotate, indicating they are unlocked.

10.6 One Key Takeoff/Landing

1. After unlocking motors, short press the One Key Takeoff/Landing button. The drone will automatically take off and hover at 5 feet. Control with joysticks.
2. During flight, short press the One Key Takeoff/Landing button again to land the drone automatically.

11.0 Functions Details

11.1 Emergency Stop

Use only in emergencies to prevent damage or injury. Simultaneously press the Record Video button and the Lens Down button. The transmitter will beep once, and the drone will fall immediately. Be aware of potential damage from impact.

11.2 Speed Switch

The drone has 2 speed modes (Low/High). Press the Speed Switch button to toggle. "Di" tone for Low speed (default), "DiDi" for High speed.

11.3 Take Photo/Record Video

Take Photo: Short press the Photo button. One beep indicates a photo taken. Record Video: Short press the Video button. Two beeps indicate recording started. Press again to stop. Do not take photos during recording.

11.4 Camera Angle Adjustment

Adjust the camera tilt (up/down) using the dedicated buttons on the transmitter. The camera has a 90° tilt range.

11.5 Headless Mode

After pairing/calibration, short press the Headless Mode Button to enter. Drone indicator lights will flash, and transmitter will beep continuously. Press again to exit (lights turn solid, one beep). In Headless Mode, the drone's forward direction is relative to its orientation at takeoff. It is recommended to face the same direction as the drone's head at takeoff for easier control.

11.6 Optical Flow Positioning

Uses optical flow lens modules to acquire position information via visual images for precise positioning, typically indoors. Works best below 20 feet (6 meters). Precision is affected by light strength and surface textures. Exercise caution when flying over monochrome surfaces, reflective surfaces, water, moving objects, areas with dramatic light changes, extremely dark/bright surfaces, surfaces without clear textures, highly repeating textures, or surfaces tilting over 30 degrees. Maintain clean sensors. The vision system may not function properly over water, low light, or surfaces without clear patterns.

11.7 Altitude-Hold Function

The drone maintains its altitude when the left joystick is released (it automatically springs back to the middle).

12.0 Specifications

Drone

• Model: HS260
• Weight: 145g / 5.11oz
• Max Flight Time: 15 minutes (per battery)
• Operating Temperature Range: 32° to 104°F (0° to 40°C)
• Size (Unfolded): 313 × 213 × 55 mm
• Size (Folded): 145 × 70 × 55 mm

Drone Battery

• Capacity: 1300 mAh
• Voltage: 3.85 V
• Battery Type: Lithium-ion Polymer Battery
• Energy: 5.01 Wh
• Charging Temperature Range: 41° to 104°F (5° to 40°C)
• Charging Time: ~60 minutes

Transmitter

• Operating Frequency: 2452-2474 MHz
• Max Flight Distance: 328 feet / 100 m (outdoor and unobstructed)
• Battery Type: 4 × AAA Battery (not included)
• Operating Temperature Range: 32° to 104°F (0° to 40°C)

Camera

• Operating Frequency: 2417 MHz
• Photo/Video Resolution: 1920×1080P
• Transmission Distance: 197~262 feet / 60~80 m (outdoor and unobstructed)
• Lens Angle: 75°
• Adjustment Range: -90° to 0°
• Live View Quality: 25 fps
• Photo Formats: JPEG
• Video Formats: AVI/MP4
• Operating Temperature Range: 32° to 104°F (0° to 40°C)

USB Charging Cable

• Input: 5V / 2A
• Rated Power: ≤10 W

13.0 Trouble Shooting

14.0 Contact Us

15.0 General Information

FCC Notice:

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) it may not cause harmful interference, and (2) it must accept any interference received. The Supplier's Declaration of Conformity is available at: https://www.holystone.com/Download/US/HS260_FCC_sDoC.pdf

This equipment has been tested and complies with Class B digital device limits. If interference occurs, try reorienting/relocating the antenna, increasing separation, connecting to a different circuit, or consulting a technician.

RF Exposure:

This equipment complies with FCC radiation exposure limits for an uncontrolled environment. Maintain a minimum distance of 20cm between the radiator and your body.

IC Notice:

This device complies with Canada Industry licence-exempt RSS standard(s). Operation is subject to two conditions: (1) this device may not cause interference; and (2) this device must accept any interference, including that which may cause undesired operation.

How to Recycle This Product:

This symbol indicates the product must not be disposed of with household waste. Separate for responsible recycling to foster sustainable re-use. Contact your retailer, local town hall, or business store for recycling information.

Battery Warning:

Failure to follow instructions can result in serious injury, damage, fire, smoke, or explosion. Always check battery condition. Replace if dropped, smells peculiar, overheats, discolors, deforms, or leaks. Use only approved LiPo chargers. Never charge on flammable surfaces or unattended. Do not disassemble, modify, puncture, or short-circuit batteries. Avoid moisture, direct sunlight, or temperatures above 60°C (140°F). Keep out of reach of children/pets. Non-rechargeable batteries are not allowed to be recharged. Rechargeable batteries should be charged under adult supervision. Do not mix different battery types.