Home - Ecoer HVAC Heating And Cooling Smart Equipment
Owner's Manual for ecoer models including: MGH Series, MGH Series Gas Furnace, Gas Furnace, Furnace
Owner's Guide - Ecoer HVAC Heating And Cooling Smart Equipment
File Info : application/pdf, 4 Pages, 769.05KB
DocumentDocumentOwner's Guide Ecoer Gas Furnace series Read and save these instruction before use ©2023 ECOER INC. 43671 Trade Center Place, Suite 100Dulles, VA 20166 USA Tel: 703-348-2538 www.ecoer.com Warm your home Ecoer launched is first condensing furnace MGH series. Ecoer utilizes multiple technologies to provide its customers a highquality furnace that saves energy. At Ecoer, We believe it is time for a new era of heating through your furnace. Ecoer is committed to creating a comfortable home environment. The MGH series furnace will heat your entire home while providing the warmth your family needs during the winter months. NOTE: Please read all instruction in the manual and retain all manuals for future reference. Attention WARNING FIRE OR EXPLOSION HAZARD The furnace is designed and approved for use with Natural Gas and (LP)Propane Gas ONLY. DO NOT BURN ANY LIQUID FUEL OR SOLID FUEL IN THIS FURNACE. Burning any unapproved fuel will result in damage to the furnace heat exchanger, which could result in Fire, Personal Injury, and/or Property Damage. WARNING FIRE, EXPLOSION, ELECTRICAL SHOCK, AND CARBON MONOXIDE POISONING HAZARD Failure to follow this warning could result in dangerous operation, serious injury, death, or property damage. Improper installation, adjustment, alteration, service, maintenance, or use could cause carbon monoxide poisoning, explosion, fire, electrical shock, or other conditions which may cause personal injury or property damage. Consult a qualified service agency, local gas supplier, or your distributor or branch for information or assistance. The qualified service agency must use only factory-authorized and listed kits or accessories when modifying this product. Download the App If you purchase the Ecoer Smart WiFi Thermostat, you can use the App which helps to control remotely. Several ways to download the Ecoer Home Plus App: · Search for "Ecoer Home Plus" on Google Play Store or Apple App Store, then download. · Download the app by scanning the QR code below. Ecoer Home Plus iOS Android Download on the APP Store GET IT ON Google Play There may be updates to the APP version. Log in to www.ecoer.com or contact support@ecoer.com To obtain the latest guidelines. To learn more about the APP, WE ARE HERE TO HELP: Addr.: 43671 Trade Center Place, Suite 100 Dulles, VA 20166 USA Tel: (703) 348-2538 Website: www.ecoer.com Setting the temperature Control your room temperature via the thermostat : 1. Place the system mode switch on HEAT. 2. Place the fan switch on AUTO. 3. Set the temperature by using the indicator on the thermostat control. 4. The system will operate whenever the room temperature falls below the temperature setting. 5. Once the desired temperature is reached, the system will shut off. Homeowner maintanance The Gas furnace system is a self-contained system that must require professional maintenance and repair. Other than performing the simple maintenance recommended in this manual, please do not make any adjustments to your system. Your contractor will be able to take care of any questions or problems you may have. CAUTION To prevent injury, death, or property damage, read and follow all instructions and warnings, including labels shipped with or attached to unit before operating your new outdoor system. WARNING Disconnect all electrical power to the indoor air handler or furnace before removing access panels to perform any maintenance. Disconnect power to both the indoor and outdoor units. NOTE: There may be more than one electrical disconnect switch. Electric shock can cause personal injury or death. CAUTION Although special care has been taken to minimize sharp edges in the construction of your unit, be extremely careful when handling parts or reaching into the unit. Clean or replace the filter every one mouth WARNING CARBON MONOXIDE AND POISONING HAZARD Failure to follow this warning could result in personal injury, or death. Never operate a furnace without a filter or with filter access door removed. Help ensure top efficiency by cleaning or replacing the filter every one month. One of the most common causes of a problem in furnace is a blocked or dirty filter. Filters should be cleaned (permanent) or replaced (disposable) every one month or as required. When rep|acing a filter, it must be replaced with a filter of the same type and size. Become familiar with filter location and procedures for removal, cleaning and replacing them. If help is needed, contact the installer of the furnace or a qualified serviceman. Inspect filter. If your dirty filter is the disposable type, replace dirty filter with the same type and size filter. If your dirty filter is a permanent filter, clean as follows: · Wash, rinse, and dry the permanent filters. Both sides should then be sprayed with a filter adhesive as is recommended on the adhesive container. Many hardware stores stock spray adhesives for use with permanent filters. · If badly torn or uncleanable, these filters must be replaced by equal size permanent, high velocity filters. Throwaway filters must not be used as replacement for permanent filters. Under normal use, permanent filters should last for several years. If you cannot remove it yourself, please contact your contractor. NOTE:*Ecoer does not supply filters or filter racks with furnace units. All filters must be field supplied according to the Manufacturer recommended high velocity filter sizes and specifications shown below. Furnace cabinet width (inch) Filter Size * (inch) Side return Bottom return Filter type 17-1/2 16 x 25 16 x 25 High Velocity(600 FPM) 21 16 x 25 20 x 25 High Velocity(600 FPM) 24.5 16 x 25 24 x 25 High Velocity(600 FPM) Troubleshooting p If you can't open the gas furnace, please check whether it is overdue charges. p For any problems encountered while using the gas furnace, please contact your contractor. Yearly contractor maintenance The furnace should be inspected by a qualified installer, or service agency at least once per year. This check should be performed at the beginning of the heating season. This will ensure that all furnace components are in proper working order and that the heating system functions appropriately. Your annual system inspection should include: · All flue gas carrying areas external to the furnace (i.e. chimney, vent connector) are clear and free of obstructions. · The vent connector is in place, slopes upward and is physically sound without holes or excessive corrosion. · The return-air duct connection(s) is physically sound, is sealed to the furnace casing, and terminates outside the space containing the furnace. · The physical support of the furnace is sound without sagging, cracks, gaps, etc, around the base so as to provide a seal between the support and the base. · There are no obvious signs of deterioration of the furnace. · The pilot and burner flames are in good adjustment (by comparison with pictorial sketches or drawings of the main burner flame and, if applicable, the pilot burner flame). Call your contractor for additional routine maintenance Your gas furnace must be inspected regularly by a properly trained contractor. For regular contractor maintenance please refer to www.ecoer.com WARNING Installation and service must be performed by a qualified installer, service agency or the gas supplier.