TP-Link Community
CE Regulatory Compliance | TP-LinkTP-Link Product Support - Wireless Networking Equipment SupportRegulatory Compliance | TP-Link
Instructions for tp-link models including: TL-SF1008LP, TL-SF1008P, TL-SF1009P, TL-SL1311P, TL-SL1311MP, TL-SF1008LP Unmanaged Desktop PoE Plus Switch, TL-SF1008LP, Unmanaged Desktop PoE Plus Switch, Desktop PoE Plus Switch
Download für TL-SL1311MP | TP-Link Deutschland
Download for TL-SL1311MP | TP-Link
File Info : application/pdf, 2 Pages, 191.94KB
DocumentDocument© 2024 TP-Link 7106510937 REV7.4.0 Installation Guide Unmanaged Desktop PoE+ Switch LED Explanation Power On: Power on Off: Power off PoE Status On: PoE power provided Flashing: Current-overload/ Short-circuit Off: No PoE power provided Link/Act On: Link present but no activity Flashing: Transmitting/receiving data Off: No link PoE MAX TL-SF1008LP Off: Total power supply < 34 W On: 34 W Total power supply < 41 W Flashing: Total power supply 41 W TL-SF1008P Off: Total power supply < 59 W On: 59 W Total power supply < 66 W Flashing: Total power supply 66 W TL-SF1009P/TL-SL1311P Off: Total power supply < 58 W On: 58 W Total power supply < 65 W Flashing: Total power supply 65 W TL-SL1311MP Off: Total power supply < 117 W On: 117 W Total power supply < 124 W Flashing: Total power supply 124 W Switches Explanation Note: The numbers in brackets indicate the ports where the feature takes effect. For example, when Extend(1-4) is toggled to On, the Extend mode will be enabled for ports 1-4. Extend (for TL-SF1008LP/TL-SF1008P/TL-SF1009P/TL-SL1311P/TL-SL1311MP) Recovery (For TL-SF1008LP/TL-SF1008P/TL-SF1009P/TL-SL1311P/TL-SL1311MP) Off: Ports run at 10/100 Mbps and support PoE power supply up to 100 m away. On: Ports run at 10 Mbps and support PoE power supply up to 250 m away. Off: The PoE Auto Recovery function is disabled. On: The switch will constantly detect the working status of a PoE powered device (PD). When the switch finds that the PD works abnormally, the switch will reboot it. Priority (For TL-SF1008LP/TL-SF1008P/TL-SF1009P) Isolation (For TL-SF1009P/TL-SL1311P/TL-SL1311MP) Off: All the ports transmit data with the same priority. On: Port 1 and 2 transmit data in a higher priority than other ports. When congestion occurs, packets which are transmitted by the ports with higher priority occupy the whole bandwidth. Off: Ports can transmit data with each other. On: Specfic ports cannot transmit data with other downlink ports. They can transmit data only with the uplink ports. Note: For simplicity, we will take TL-SF1008P for example throughout the Guide. Connection Ethernet Ports (1-8) DC Power Adapter AC Power Cord Internet PC Note: 1. PoE ports can also connect to non-PoE devices, but only transmit data. 2. TL-SL1311MP/TL-SL1311P has three uplink ports, which typically connect to uplink devices like routers. Uplink 1 is an SFP slot and works with a 1000 Mbps SFP module. Uplink 2 and uplink 3 are RJ45 ports. PoE Ports (1-4) Powered Device (PD) IP Camera AP IP Phone Specifications General Specifications Standard Protocol IEEE 802.3i, IEEE 802.3u, IEEE 802.3x, IEEE 802.3af, IEEE802.3at IEEE802.3ab (Only for TL-SL1311P and TL-SL1311MP) IEEE802.3z (Only for TL-SL1311P and TL-SL1311MP) CSMA/CD Interface TL-SF1008LP/TL-SF1008P: 8 10/100 Mbps RJ45 Ports Auto-Negotiation/Auto MDI/MDIX PoE Ports: Port 14 TL-SF1009P: 9 10/100 Mbps RJ45 Ports Auto-Negotiation/Auto MDI/MDIX PoE Ports: Port 18 TL-SL1311P/TL-SL1311MP: 8 10/100 Mbps RJ45 Ports Auto-Negotiation/Auto MDI/MDIX 2 10/100/1000 Mbps RJ45 Ports Auto-Negotiation/Auto MDI/MDIX 1 1000 Mbps SFP slot PoE Ports: Port 18 Network Media (Cable) 10BASE-T: UTP category 3, 4, 5 cable (maximum 100 m) EIA/TIA-568 100 STP (maximum 100 m) 100BASE-TX: UTP category 5, 5e cable (maximum 100 m) EIA/TIA-568 100 STP (maximum 100 m) 1000BASE-T (Only for TL-SL1311P and TL-SL1311MP): UPT category 5e cable or above (maximum 100m) EIA/TIA-568 100 STP (maximum 100 m) 1000BASE-SX/LX/LX10/BX10 (Only for TL-SL1311P and TL-SL1311MP): MMF, SMF Switching Capacity TL-SF1008LP/TL-SF1008P: 1.6 Gbps TL-SF1009P: 1.8 Gbps TL-SL1311P/TL-SL1311MP: 7.6 Gbps Transfer Method Store-and-Forward MAC Address Learning Automatically learning, automatically aging Power Supply External Power Adapter Input: 100-240 VAC, 50/60 Hz Output: TL-SF1008LP: 53.5 VDC/0.81 A TL-SF1008P/TL-SF1009P/TL-SL1311P: 53.5 VDC/1.31 A TL-SL1311MP: 53.5 VDC/2.43A PoE Budget TL-SF1008LP: 41 W (up to 30 W for each PoE port) TL-SF1008P: 66 W (up to 30 W for each PoE port) TL-SF1009P/TL-SL1311P: 65 W (up to 30 W for each PoE port) TL-SL1311MP: 124 W (up to 30 W for each PoE port) Wall Mountable Distance Between Mounting Holes Yes TL-SF1008LP/TL-SF1008P/TL-SF1009P: 105 mm TL-SL1311P/TL-SL1311MP: 150 mm Environmental and Physical Specifications Certification Operating Temperature Storage Temperature Operating Humidity Storage Humidity FCC, CE, RoHS -5°C to 40°C (23°F to 104°F) (For TL-SF1009P) 0°C to 40°C (32°F to 104°F) (For other switches) -40°C to 70°C (-40°F to 158°F) 10% to 90% non-condensing 5% to 90% non-condensing Frequently Asked Questions (FAQ) Q1. The Power LED is not lit. The Power LED should be lit when the power system is working normally. If the Power LED is not lit, please check as follows: A1: Make sure the AC power cord is connected the switch with power source properly. A2: Make sure the voltage of the power supply meets the requirements of the input voltage of the switch. A3: Make sure the power source is on. Q2. The Link/Act LED is not lit when a device is connected to the corresponding port. It is recommended that you check the following items: A1: Make sure that the cable connectors are firmly plugged into the switch and the device. A2: Make sure the connected device is turned on and working well. A3: The cable must be less than 100 meters long (328 feet). If Extend Mode is enabled, it should be less than 250 meters (820 feet). Q3. Why are PoE ports not supplying power for PoE devices? When the total power consumption of connected PoE devices exceeds the maximum, the PoE port with a smaller port number has a higher priority. The system will cut off power to the ports with larger port numbers to ensure supplying to other ports. Take TL-SF1008P as an example. If port 1, 2 and 4 are consuming 15.4 W respectively, and an additional PoE device with 20 W is inserted to port 3, the system will cut off the power of port 4 to compensate for the overload. Q4. What should I notice before using the PoE Auto Recovery feature? A1: Before upgrading a connected PoE powered device (PD), disable PoE Auto Recovery to avoid the PD's damage. A2: When a PD does not send data packets to the switch for a long period in certain scenarios (e.g. an IPC in sleep mode), disable PoE Auto Recovery to avoid the PD repeatedly rebooting. To ask questions, find answers, and communicate with TP-Link users or engineers, please visit https://community.tp-link.com to join TP-Link Community. For technical support and other information, please visit https://www.tp-link.com/support, or simply scan the QR code. EU declaration of conformity TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2011/65/EU and (EU)2015/863. The original EU declaration of conformity may be found at https://www.tp-link.com/en/support/ce/ UK declaration of conformity TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016. The original UK declaration of conformity may be found at https://www.tp-link.com/support/ukca/ Safety Information Keep the device away from water, fire, humidity or hot environments. Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us. Place the device with its bottom surface downward. Do not use damaged charger or USB cable to charge the device. Do not use any other chargers than those recommended. Adapter shall be installed near the equipment and shall be easily accessible. The plug on the power supply cord is used as the disconnect device, the socket-outlet shall be easily accessible. The socket-outlet shall be installed near the equipment and shall be easily accessible.