Categories: MEEC TOOLS

MEEC TOOLS 016453 241 Compressor Instruction Manual

MEEC TOOLS 016453 241 Compressor

SAFETY INSTRUCTIONS

  • Keep the work area clean and tidy. Cluttered work areas put safety at risk.
  • Do not expose the product to rain or moisture.
  • Do not use the product in damp or wet areas.
  • Keep the work area well lit.
  • Do not use product where combustible gas or liquids are stored or used.
  • Avoid the risk of electric shock. Do not touch earthed objects, such as water pipes, radiators, hot plates or cookers.
  • Keep other people and pets at a safe distance.
  • Persons not involved in the work should be kept at a safe distance from the work area and do not allow anyone, especially children, to touch the product or the power cord.
  • When not in use, store the product in a dry place, locked up and out of the reach of children.
  • Do not overload the product. The work will be safer and better if the product is not overloaded.
  • Wear suitable clothing. Do not wear loose-fitting clothing or jewellery.
  • They can get caught in moving parts.
  • Wear non-slip shoes when working outside.
  • Wear a hair net if you have long hair.
  • Use personal safety equipment.
  • Wear safety glasses.
  • Wear a breathing mask or dust filter mask if the work produces a lot of dust.
  • Protect the power cord from damage, and replace a damaged cord immediately.
  • Do not pull the power cord to unplug the plug from the power point. Keep the power cord away from heat, oil and sharp edges.
  • If the power cord or plug get damaged they must be replaced by an authorised electrician.
  • Check that the product is clean and free from contamination.
  • Follow all the directions for care, maintenance and storage.
  • Check the power cord and plug at regular intervals. If the power cord or plug get damaged they must be replaced by an authorised electrician.
  • Check any extension cords are regular intervals. Replace damaged extension cords.
  • Keep the handles clean, dry and free from oil and grease.
  • Always unplug the product when it is not in use, before service and maintenance, and before changing tools.
  • Avoid accidental starting. Check that the power switch is in the OFF position before plugging the plug into a power point.
  • Always use the correct type of extension cord.
  • If the product is used outdoors, only use an extension cord approved for outdoor use.
  • Stay alert at all times. Use your common sense. Never use the product if you are tired or under the influence of drugs, alcohol or medication.
  • Check that the product is undamaged.
  • Check before using the product that it is working normally as described in these instructions.
  • Check that all moving parts are undamaged, correctly fitted and that they do not jam.
  • Damaged safety devices must be replaced by an authorised service centre, unless otherwise specified in the instructions.
  • A damaged power switch must be replaced by an authorised electrician.
  • Do not use the product if it cannot be switched on and off with the power switch.
  • Do not use accessories other than those specified in these instructions or recommended by the manufacturer or retailer – risk of personal injury.
  • Repairs should be carried out by qualified personnel.
  • The product complies with the applicable safety regulations. Repairs may only be carried out by qualified personnel using identical spare parts.
  • Serious personal injury can otherwise occur.
  • Risk of hearing impairment. Wear ear protection when using the compressor.
  • Risk of explosion. Never use the product where flammable material, liquid or gas (petrol, solvent, gas cylinders etc.) are stored or used.
  • Never switch off the product by pulling out the plug. Always use the ON/OFF power switch or button.
  • Always pull out the plug and relieve the pressure in the air tank before moving the product, and before service or repairs.
  • Keep the power cord away from heat, oil and sharp edges.
  • Do not carry or pull the product by the power cord or the air hoses. The product must only be carried with the handle.
  • Check that all the air hoses and air tools to be connected to the compressor are approved for the air pressure produced by the compressor, and that they are correctly connected.
  • The product is intended to be used in a well ventilated area and ambient temperature of 5 to 40°C.
  • Do not expose the product to water or any other liquid.
  • Do not use the product if the air tank is in any way damaged.
  • Check that all the air hoses are undamaged and approved for the pressure produced by the compressor.
  • Damaged air hoses must be replaced – never attempt to repair a damaged air hose
  • Keep children under supervision to make sure they do not play with the product.

WARNING! 

The air supply to the compressor must be disconnected if an air hose breaks or is damaged. A broken air hose is extremely dangerous and can rotate at great speed, causing injury to persons nearby and blowing foreign objects into the air.
Do not attempt to catch the hose, but immediately evacuate all onlookers from the risk area, turn off the air supply, switch off the compressor with the power switch and then remove the hose from the compressor.

TECHNICAL DATA

Always wear ear protection.
The declared values for vibration and noise, which have been measured by a standardised test method, can be used to compare different tools with each other and for a preliminary assessment of exposure. The measurement values have been determined in accordance with EN 1012-1 :2010.

WARNING!
The actual vibration and noise level when using tools may differ from the specified maximum value, depending on how the tool is used and the material. It is therefore necessary to determine which safety precautions are required to protect the user, based on an estimate of exposure in actual operating conditions (taking into account all stages of the work cycle, e.g. the time when the tool is switched off and when it is idling, in addition to the start-up time).

DESCRIPTION

  1. Condensation drain plug
  2. Air tank
  3. Wheel
  4. Foot
  5. Quick-coupling (outlet pressure)
  6. Pressure gauge (outlet pressure)
  7. Pressure relief valve
  8. Switch
  9. Transport handle
  10. Pressure gauge (pressure in air tank)
  11. Safety valve
  12. Air filter
    FIG. 1

INSTALLATION

UNPACKING 

Unpack all the parts and check that nothing is missing or damaged. If possible save the packaging until the warranty has expired.
WARNING!
Do not allow children to play with the product or the packaging material. Keep the packaging material and all the small parts out of the reach of children – risk of suffocation.

Contents

  • 2 wheels
  • 1 air filter
  • 1 foot
  • 1 sole for foot
  • 2 hex screws M6
  • 1 flat washer r/J 6.4 mm
  • 1 spring washer r/J 6.4 mm
  • 2 wheel screws
  • 1 flat washer r/J 70.4 mm
  • 1 spring washer r/J 10.4 mm
  • 1 hex nut M10

TOOLS FOR ASSEMBLY 

2 combination spanners, 14 and 17 mm are required for the assembly (sold separately).

FITTING THE WHEELS 

  1. Insert the wheel screw (e) through the hole (3). Now put the wheel screw through the hole in the compressor. Put the flat washer
    (f) and spring washer (g) on the screw, screw on the hex nut (h) and tighten.
  2. Fit the other wheel (3) in the same way. FIG. 2

 FITTING THE SUPPORT LEG 

Put the hex screw (a) through the side  foot (4). Lift up the side foot and screw, put the screw (a) through the hole, put on the flat washer (c) and spring washer (b), and then screw on the nut (b).

 FITTING THE AIR FILTER 

The supplied air filter (12) must be fitted before using the compressor.

 NOTE: 

The compressor must not be used without the air filter.

FITTING THE COMPRESSED AIR HOSE

An extension hose can be used if the compressor cannot be placed in the immediate vicinity of the workplace (sold separately). Connect the quick-coupling on the extension hose to one of the quick-couplings on the compressor (5 or 11). Now connect the pneumatic tool to the quick-coupling on the other end of the hose.

USE

PREPARATIONS 

  • Check that the mains voltage corresponds to the rated voltage on the type plate.
  • Install the compressor as close as possible to the air consumption -the air hoses and cords should be as short as possible.
  • Make sure the intake air to the compressor is dry and free from dust.
  • Do not install the compressor in a damp area.
  • The compressor is intended to be used in a well ventilated area and an ambient temperature of +5 to +40°C. The room should be free from dust, acid, fumes and flammable or explosive gas.
  • The compressor is only intended to be used in dry areas. It must not be used in places where work is carried out with sprayed water.

POWER SUPPLY

  • The electric motor is ready for use on delivery. The electrical circuits comply with the requirements in the VDE and DIN standards. The power point to which the product is connected and any extension cords must also comply with the requirements in these standards.
  • The product has a power cord with an earthed plug. The plug can be connected to an earthed 230 V 50 Hz power point with a fuse of at least 16 A.
  • Check that the mains voltage corresponds to the rated voltage on the type plate on the product.
  • Long extension cords can result in loss of voltage and make starting the motor more difficult. Extension cords up to 25 m must have a minimum cross-sectional wire area of at least 1.5 mm2
  • The connection and the repair of electrical equipment must only be carried out by an authorised electrician.
  • An ambient temperature below +5° C can also make starting more difficult or impossible.

INTENDED USE 

  • The compressor is intended to be used for pneumatic tools with low air consumption (up to 1071/min), for example tyre pump nozzles, blower nozzles and paint guns. The compressor is not suitable for tools with a high consumption of air, such as grinders or impact wrenches.
  • The compressor must only be used as it is intended to be used. All other use is considered to be unsuitable.
    The product is not intended for commercial or industrial use. Commercial or industrial use will invalidate the warranty.

HOW TO USE

Starting/stopping

Put the switch (8) in position “I” to start the compressor. Put the switch (8) in position “O” to switch off the compressor.

SETTING THE WORKING PRESSURE
The air pressure can be read off on the pressure gauge (6) and adjusted with the pressure reduction valve (7). The set pressure is taken out through the quick-coupling (5).

PRESSURE SWITCH
The pressure switch is set at the factory and the difference in pressure between starting and stopping is normally 2 bar-the compressor normally starts when the pressure in the air tank has dropped to 6 bar and stops when the pressure increases to 8 bar.

MAINTENANCE

  • Switch off the product, pull out the plug and wait until all moving parts have completely stopped before cleaning or maintenance – risk of electric shock and serious personal injury.
  • Wait until the product has cooled – risk of burn injury.
  • Relieve the pressure in the product before cleaning or maintenance – risk of personal injury.

CLEANING

  • Keep the safety devices, ventilation openings and the motor housing free from dust and dirt.
  • Clean the product after it has been used.
  • Wipe clean with a clean cloth, or blow clean with compressed air at low pressure.
  • Clean the product at regular intervals with a cloth moistened with water and a mild detergent. Do not use strong detergents or solvents, they can damage the plastic parts. Make sure that no water gets into the product.
  • Disconnect hoses and pneumatic tools from the compressor before cleaning. Do not clean the compressor with water or solvent.

Cleaning the air filter 

  1. Turn the air filter casing (12) in the direction of the arrow and remove it.
  2. Take the paper insert (i) out of the filter housing.
  3. Tap the paper insert (i) and filter housing to shake off any impurities. Vacuum clean the insert and filter housing if necessary. Refit in the reverse order.

FIG. 6


MAINTENANCE OF AIR TANK
IMPORTANT:

Drain all the condensation from the air tank (2) after use to reduce the risk of rusting.
Relieve the pressure in the air tank first by opening the safety valve (14), unscrewing the condensation drain plug (1) (screw anticlockwise), and allowing the condensation to run out. Replace the drain plug (screw clockwise). Check the air tank before use for signs of rust and other damage. Do not use the compressor if the air tank is damaged or rusty- contact an approved service centre.

POWER CORD 

The insulation in the cord can easily become damaged Frequent types of damage are:

  • pinching when the cord passes through windows or doors
  • creasing if the cord is not hung up or fastened properly
  • damage caused by being run over
  • damage cause by pulling the cord (always pull the plug)
  • fatigue.

WARNING! 

Cords with damaged insulation are dangerous and must not be used under any circumstances.

  • Check at regular intervals all power cords for damage to the insulation.
  • Unplug the power cord from the power point before checking. Cord must comply with the requirements in the VDE and DIN standards. Only cords marked HOSVV-F must be used (type marking of cords is mandatory).

STORAGE

Store the product and all accessories in a clean, dry frost-free place, protected from direct sunlight and out of the reach of children. The best storage temperature is +5 to +30°C.

IMPORTANT: 

  • Switch off the switch, pull out the plug and relieve the pressure (air tank, connected pneumatic tools etc.). Secure the power switch from accidental switching.
  • Store the product upright (never flat or leaning) in a dry place out of the reach of children and other unauthorised persons.

PRESSURE RELIEF/EMPTYING 

Relieve the pressure by switching off the compressor and running all the air out of the tank with a pneumatic tool, or blowing out the air with a blower.

TRANSPORT 

Use the transport handle (1) to carry the product, or to run it on its wheels.
Take into consideration the weight of the product when lifting (see technical data). Safely secure the product when transporting it in a vehicle.

TROUBLESHOOTING

See table on the next page.

Documents / Resources

MEEC TOOLS 016453 241 Compressor [pdf] Instruction Manual
016453, 241 Compressor, 016453 241 Compressor
Share

Recent Posts

breeze33 BZ33-HYP12WALL2-G2-P Premier Series DC Inverter Heat Pump Instruction Manual

BZ33-HYP12WALL2-G2-P Premier Series DC Inverter Heat Pump FACTORY CODE: 22022011016261 MINI SPLIT REPLACEMENT PARTS GUIDE…

1 min ago

OSD AUDIO NERO Mini HT Satellite Speaker User Guide

NERO Mini HT Satellite Speaker NERO Mini HT SATELLITE SPEAKER 86(5·6*8,'( 1(520LQL86(5·6*8,'( Safety Instructions 1.…

2 mins ago

Danfoss 100B1200 ECL Comfort 120 ECL Controller Installation Guide

100B1200 ECL Comfort 120 ECL Controller Installation Guide ECL Comfort 120 (code no. 100B1200, 100B1600,…

2 mins ago

RENISHAW REVO-2 Vision Probe User Manual

REVO-2 Vision Probe REVO-2 and RSP2 probes The REVO-2 dynamic measuring system is designed to…

7 mins ago

IFIXIT 53235 Stuck Shutter Fix Replacement Instruction Manual

53235 Stuck Shutter Fix Replacement Stuck Shutter Fix Replacement Guide ID: 53235 - Draft: 2022-08-31…

9 mins ago

Linocell 12W Mini USB Lader Wall Charger User Manual

12W Mini USB Lader Wall Charger

9 mins ago