MEAN WELL RD-65A Serie Dual Output Switching Power Supply Owner's Manual

MODEL		RD-65A		RD-65B
OUTPUT	OUTPUT NUMBER	CH1	CH2	CH1	CH2
	DC VOLTAGE	5V	12V	5V	24V
	RATED CURRENT	6A	3A	4A	2A
	CURRENT RANGE Note.6	0-8A	0-4A	0-8A	0- 3A
	RATED POWER Note.6	66W		68W
	RIPPLE & NOISE (max.) Note.2	80mVp-p	120mVp-p	80mVp-p	150mVp-p
	VOLTAGE ADJ. RANGE	CH1: 4.75 – 5.5V		CH1: 4.75- 5.5V
	VOLTAGE TOLERANCE Note.3	±2.0%	±6.0%	± 2.0%	+4,-8%
	LINE REGULATION Note.4	±0.5%	±1.5%	±0.5%	±2.0%
	LOAD REGULATION Note.5	±0.5%	±3.0%	±0.5%	±6.0%
	SETUP, RISE TIME	500ms, 20ms/230VAC 1200ms, 30ms/115VAC at full load
	HOLD UP TIME (Typ.)	60ms/230VAC 14ms/115VAC at full load
INPUT	VOLTAGE RANGE	88- 264VAC 125- 373VDC (Withstand 300VAC surge for 5sec. Without damage)
	FREQUENCY RANGE	47- 63Hz
	EFFICIENCY(Typ.)	78%		77%
	AC CURRENT (Typ.)	2A/115VAC 1.2A/230VAC
	INRUSH CURRENT (Typ.)	COLD START 50A/230VAC
	LEAKAGE CURRENT	<2mA/ 240VAC
PROTECTION	OVERLOAD	110 – 150% rated output power
		Protection type: Hiccup mode, recovers automatically after fault condition is removed
	OVER VOLTAGE	CH1: 5.75- 6.75V
		Protection type: Hiccup mode, recovers automatically after fault condition is removed
ENVIRONMENT	WORKING TEMP.	-25 – +70°C (Refer to “Derating Curve”)
	WORKING HUMIDITY	20 – 90% RH non-condensing
	STORAGE TEMP., HUMIDITY	-40- +85°C, 10-95% RH
	TEMP. COEFFICIENT	± 0.03%/°C (0 – 50°C )on +5V output
	VIBRATION	10-500Hz, 5G 10min./1cycle, period for60min. each along X, Y, Z axes
SAFETY & EMC (Note 7)	SAFETY STANDARDS	UL62368-1, TUV BS EN/EN62368-1 , EAC TP TC 004 approved
	WITHSTAND VOLTAGE	I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
	ISOLATION RESISTANCE	I/P-0/P, I/P-FG, O/P-FG:100M Ohms/ 500VDC / 25″C/ 70% RH
	EMC EMISSION	Compliance to BS EN/EN55032 (CISPR32) Class B, BS EN/EN61000-3-2,-3, EAC TP TC 020
	EMC IMMUNITY	Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11, BS EN/EN55035, BS EN/EN61000-6-2 (BS EN/EN50082-2), heavy industry level, EAC TP TC 020
OTHERS	MTBF	2940.2K hrs min. Telcordia SR-332 (Bellcore); 541.0K hrs min. MIL-HDBK-217F (25’C)
	DIMENSION	129’98’38mm (L’W’H)
	PACKING	0.44Kg; 30pcs/14.2Kg/0.72CUFT
NOTE	All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature. Ripple & noise are measured at 20MHz of bandwidth by using a 12″ twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. Tolerance: includes set up tolerance, line regulation and load regulation, when multi-channel output, it is recommended that CH1 load> 10%. Line regulation is measured from low line to high line at rated load. Load regulation is measured from 20% to 100% rated load, and other output at 60% rated load. Each output can work within current range. But total output power can’t exceed rated output power. The power supply is considered a component which will be installed into a final equipment. All the EMC tests are been executed by mounting the unit on a 360mm’360mm metal plate with 1mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.” (as available on http://www.meanwell.com) The ambient temperature derating of 3SC/1000m with fanless models and of 5″C/1000m with fan models for operating altitude higher than 2000m(6500ft) Product Liability Disclaimer : For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx

Mechanical Specification

Terminal Pin No. Assignment

Pin No.	Assignment	Pin No.	Assignment
1	AC/L	4,6	DC OUTPUT COM
2	AC/N	5	DC OUTPUT +V2
3	FG ½	7	DC OUTPUT +V1

Block Diagram

Derating Curve

Output Derating VS Input Voltage

Customer Support

Arrow.com

Documents / Resources

MEAN WELL RD-65A Serie Dual Output Switching Power Supply [pdf] Owner's Manual
RD-65A Serie Dual Output Switching Power Supply, RD-65A Serie, Dual Output Switching Power Supply, Switching Power Supply, Power Supply

References

User Manual

Features

GTIN CODE

SPECIFICATION