MEAN-WELL-logo

MEAN WELL NPF-60D Series 60W Single Output LED Driver

MEAN-WELL-NPF-60D-Series-60W-Single-Output-LED-Driver-productFeatures

  • Plastic housing with class II design
  • Built-in active PFC function
  • Class 2 power unit
  • Standby power consumption <O.5W
  • IP67 rating for indoor or outdoor installations
  • Function: 3 in 1 dimming (dim-to-off)
  • Typical lifetime >50000hours
  • 5 years warranty

Applications

  • LED panel lighting
  • LED downlight
  • LED decorative lighting
  • LED tunnel lighting
  • Moving sign
  • Type “HL” for use in Class l, Division 2 hazardous (Classified) location

GTIN CODE
MW Search: https://www.meanwell.com/serviceGTlN.aspx

Description

NPF-60D series is a 60W AC/DC LED driver featuring the constant current mode output. NPF-60D operates from 90N305VAC and offers models with different rated voltage, ranging between 12V and 54V. Thanks to the high efficiency up to 90%, with the fanless design, the entire series is able to operate for -400CN+850C case temperature under free air convection. The entire series is rated with IP67 ingress protection level and is suitable to work for a variety of applications at dry, damp or wet locations. NPF-60D is equipped with the 3 in 1 dimmingfunction so as to provide the design flexibility for the LED lighting system.

Model Encoding

MEAN-WELL-NPF-60D-Series-60W-Single-Output-LED-Driver-fig-2

SPECIFICATION

MODEL NPF-60D-12 NPF-60D-15 NPF-60D-20 NPF-60D-24 NPF-60D-30 NPF-60D-36 NPF-60D-42 NPF-60D-48 NPF-60D-54
 

 

OUTPUT

RATED CURRENT 5A 4A 3A 2.5A 2A 1.67A 1.43A 1.25A 1.12A
RATED POWER 60W 60W 60W 60W 60W 60.12W 60.06W 60W 60.48W
CONSTANT CURRENT REGION 7.2 ~ 12V 9 ~ 15V 12 ~ 20V 14.4 ~ 24V 18 ~ 30V 21.6 ~ 36V 25.2 ~ 42V 28.8 ~ 48V 32.4 ~ 54V
CURRENT RIPPLE 5.0% max. @rated current
CURRENT TOLERANCE ±5.0%
SET UP TIME  Note.3 500ms/115VAC, 230VAC
 

 

 

 

 

 

INPUT

VOLTAGE RANGE Note.2 90 ~ 305VAC         127 ~ 431VDC

(Please refer to “STATIC CHARACTERISTIC” section)

FREQUENCY RANGE 47 ~ 63Hz
POWER FACTOR (Typ.) PF≧0.97/115VAC, PF≧0.95/230VAC, PF≧0.92/277VAC@full load

(Please refer to “POWER FACTOR (PF) CHARACTERISTIC” section)

TOTAL HARMONIC DISTORTION THD< 20%(@load≧60%/115VC, 230VAC; @load≧75%/277VAC)

(Please refer to “TOTAL HARMONIC DISTORTION(THD)” section)

EFFICIENCY(Typ.) 86% 87% 88% 89% 90% 90% 90% 90% 90%
AC CURRENT (Typ.) 0.8A / 115VAC         0.4A / 230VAC         0.32A / 277VAC
INRUSH CURRENT(Typ.) COLD START 50A(twidth=270μs measured at 50% Ipeak) at 230VAC; Per NEMA 410
MAX. NO. of PSUs on 16A CIRCUIT BREAKER 9 units (circuit breaker of type B) / 16 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT <0.25mA / 277VAC
STANDBY POWER CONSUMPTION <0.5W
 

 

PROTECTION

OVER CURRENT 95 ~ 108%
Constant current limiting, recovers automatically after fault condition is removed
SHORT CIRCUIT Hiccup mode, recovers automatically after fault condition is removed
 

OVER VOLTAGE

15 ~ 17V 17.5 ~ 21V 23 ~ 27V 28 ~ 34V 34 ~ 40V 41 ~ 46V 46 ~ 54V 54 ~ 60V 59 ~ 66V
Shut down o/p voltage, re-power on to recover
OVER TEMPERATURE Shut down o/p voltage, re-power on to recover
 

 

ENVIRONMENT

WORKING TEMP. Tcase=-40 ~ +85℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)
MAX. CASE TEMP. Tcase=+85℃
WORKING HUMIDITY 20 ~ 95% RH non-condensing
STORAGE TEMP., HUMIDITY -40 ~ +80℃, 10 ~ 95% RH
TEMP. COEFFICIENT ±0.03%/℃ (0 ~ 50℃)
VIBRATION 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
 

 

 

SAFETY & EMC

 

SAFETY STANDARDS

UL8750(type”HL”), UL879(for 12V,24V only), CSA C22.2 No. 250.13-12, ENEC BS EN/EN61347-1, BS EN/EN61347-2-13, BS EN/EN62384 independent, EAC TP TC 004,GB19510.1,GB19510.14,

IP67 approved ; Design refer to BS EN/EN60335-1

WITHSTAND VOLTAGE I/P-O/P:3.75KVAC
ISOLATION RESISTANCE I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH
EMC EMISSION Compliance to BS EN/EN55015, BS EN/EN61000-3-2 Class C (@ load≧60%) ; BS EN/EN61000-3-3; GB/T 17743, GB17625.1,EAC TP TC 020
EMC IMMUNITY Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11; BS EN/EN61547, light industry level(surge immunity Line-Line 2KV); EAC TP TC 020
 

OTHERS

MTBF 3082.1K hrs min.      Telcordia SR-332 (Bellcore) ; 287.9K hrs min.      MIL-HDBK-217F (25℃)
DIMENSION 150*53*35mm (L*W*H)
PACKING 0.49Kg;30pcs/15.7Kg/1.0CUFT
NOTE 1.  All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25℃ of ambient temperature.

2.  De-rating may be needed under low input voltages. Please refer to “STATIC CHARACTERISTIC” sections for details.

3.  Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time.

4.  The standby power consumption is specified for 230VAC.

5.  The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

(as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf)

6.  This series meets the typical life expectancy of >50,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 75℃ or less.

7.  Please refer to the warranty statement on MEAN WELL’s website at http://www.meanwell.com

8.  The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft).

9.  For any application note and IP water proof function installation caution, please refer our user manual before using. https://www.meanwell.com/Upload/PDF/LED_EN.pdf

※ Product Liability Disclaimer:For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx

BLOCK DIAGRAM

MEAN-WELL-NPF-60D-Series-60W-Single-Output-LED-Driver-fig-3

DRIVING METHODS OF LED MODULES

  • This series works in constant current mode to drive the LEDs.

MEAN-WELL-NPF-60D-Series-60W-Single-Output-LED-Driver-fig-4

DIMMING OPERATION

MEAN-WELL-NPF-60D-Series-60W-Single-Output-LED-Driver-fig-5

3 in 1 dimming function

  • Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-: 0 ~ 10VDC, or 10V PWM signal or resistance.
  • Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers.
  • Dimming source current from power supply: 100μA (typ.)

Applying additive 0 ~ 10VDC

MEAN-WELL-NPF-60D-Series-60W-Single-Output-LED-Driver-fig-6MEAN-WELL-NPF-60D-Series-60W-Single-Output-LED-Driver-fig-7

Note

  1. Min. dimming level is about 6% and the output current is not defined when 0%< Iout<6%.
  2. The output current could drop down to 0% when dimming input is about 0kΩ or 0Vdc, or 10V PWM signal with 0% duty cycle.

OUTPUT LOAD vs TEMPERATURE MEAN-WELL-NPF-60D-Series-60W-Single-Output-LED-Driver-fig-8

STATIC CHARACTERISTIC MEAN-WELL-NPF-60D-Series-60W-Single-Output-LED-Driver-fig-9

POWER FACTOR (PF) CHARACTERISTIC MEAN-WELL-NPF-60D-Series-60W-Single-Output-LED-Driver-fig-10

TOTAL HARMONIC DISTORTION (THD)

MEAN-WELL-NPF-60D-Series-60W-Single-Output-LED-Driver-fig-11

POWER FACTOR (PF) CHARACTERISTIC

NPF-60D series possess superior working efficiency that up to 90% can be reached in field applications.

  • 48V Model, Tcase at 75℃ MEAN-WELL-NPF-60D-Series-60W-Single-Output-LED-Driver-fig-12

LIFE TIME MEAN-WELL-NPF-60D-Series-60W-Single-Output-LED-Driver-fig-13

MECHANICAL SPECIFICATION MEAN-WELL-NPF-60D-Series-60W-Single-Output-LED-Driver-fig-14

Recommend Mounting Direction MEAN-WELL-NPF-60D-Series-60W-Single-Output-LED-Driver-fig-15

INSTALLATION MANUAL
Please refer to: http://www.meanwell.com/manual.html

FAQs

Q: What should I do if the LED driver overheats?
A: If the LED driver overheats, immediately switch off the power supply and allow it to cool down before investigating further. Check for any obstructions to ventilation and ensure proper airflow around the driver.

Q: Can I connect multiple LED modules to one LED driver?
A: The maximum number of LED modules that can be connected to one LED driver depends on the total power consumption of the LEDs and should not exceed the maximum load capacity specified for the LED driver in the user manual.

Documents / Resources

MEAN WELL NPF-60D Series 60W Single Output LED Driver [pdf] Owner's Manual
NPF-60D-12, NPF-60D-15, NPF-60D-20, NPF-60D-24, NPF-60D-30, NPF-60D-36, NPF-60D-42, NPF-60D-48, NPF-60D-54, NPF-60D Series 60W Single Output LED Driver, NPF-60D Series, 60W Single Output LED Driver, Output LED Driver, LED Driver, Driver

References

Leave a comment

Your email address will not be published. Required fields are marked *