MEAN WELL HBG-100P Series Constant Current LED Driver User Guide?
Features
- Constant Current mode output
- Circular shape PCB type design
- Built-in active PFC function
- Function options: output adjustable via potentiometer; 3 in 1 dimming; DALI
- Typical lifetime>50000 hours
- 5 years warranty
Applications
- LED bay lighting
- LED down lighting
- LED spot lighting
- LED mining lighting
- LED stage lighting
Description
HBG-100P seriesis a 100W AC/DC PCB type LED driver featuring the circular shape design. It operates from 90~305VAC and offers constant current output models with different ratedvoltage ranging between 36V and 60V. Thanks to the high efficiency up to 91.5%, with thefanless design, the entire series is able to operate for -40°C ~ +45°C under free air convection. HBG-100P is equipped with various function options, such as dimming methodology, so as to provide the optimal design flexibility for LED lighting system.
Model Encoding
| Type | Function | Note |
| A | lo adjustable through built-in potentiometer. | ln Stock |
| B | 3 in 1 dimming function (1~10Vdc, 10V PWM signal and resistance) | ln Stock |
| DA | DALl control technology. | ln Stock |
SPECIFICATION
| MODEL | HBG-100P-36 | HBG-100P-48 | HBG-100P-60 | |||
| OUTPUT | RATED CURRENT | 2.7A | 2A | 1.6A | ||
| RATED POWER | 97.2W | 96W | 96W | |||
| CONSTANT CURRENT REGION Note.2 | 21.6 ~ 36V | 28.8 ~ 48V | 36 ~ 60V | |||
| OPEN CIRCUIT VOLTAGE(max.) | 37V | 49V | 62V | |||
| CURRENT ADJ. RANGE | Adjustable for A-Type only (via built-in potentiometer) | |||||
| 1.62 ~ 2.7A | 1.2 ~ 2A | 1.0 ~ 1.6A | ||||
| CURRENT RIPPLE | 5.0% max. @rated current | |||||
| CURRENT TOLERANCE | ±5.0% | |||||
| SET UP TIME Note.4 | 2000ms / 115VAC 500ms / 230VAC | |||||
| INPUT | VOLTAGE RANGE Note.3 | 90 ~ 305VAC 127 ~ 431VDC(Please refer to “STATIC CHARACTERISTIC” section) | ||||
| FREQUENCY RANGE | 47 ~ 63Hz | |||||
| POWER FACTOR | PF≧0.96/115VAC, PF≧0.96/230VAC, PF≧0.94/277VAC@full load(Please refer to “POWER FACTOR (PF) CHARACTERISTIC” section) | |||||
| TOTAL HARMONIC DISTORTION | THD< 20%(@load≧60%/115VC,230VAC; @load≧75%/277VAC)(Please refer to “TOTAL HARMONIC DISTORTION(THD)” section) | |||||
| EFFICIENCY (Typ.) Note.5 | 91% | 91% | 91.5% | |||
| AC CURRENT | 1.1A / 115VAC | 0.5A / 230VAC | 0.45A / 277VAC | |||
| INRUSH CURRENT(Typ.) | COLD START 60A(twidth=550μs measured at 50% Ipeak) at 230VAC; Per NEMA 410 | |||||
| MAX. No. of PSUs on 16A CIRCUIT BREAKER | 4 units (circuit breaker of type B) / 8 units (circuit breaker of type C) at 230VAC | |||||
| LEAKAGE CURRENT | <0.75mA / 277VAC | |||||
| NO LOAD / STANDBY POWER CONSUMPTION | Standby power consumption <0.5W for B/DA-Type A-Type please refer to Note. 7 | |||||
| PROTECTION | OVER CURRENT | 95 ~ 108% | ||||
| Constant current limiting, recovers automatically after fault condition is removed | ||||||
| OVER VOLTAGE | 41 ~ 49V | 54 ~ 63V | 65 ~ 75V | |||
| Shut down o/p voltage, re-power on to recovery | ||||||
| OVER TEMPERATURE Note.11 | Shut down o/p voltage, re-power on to recovery | |||||
| ENVIRONMENT | WORKING TEMP. | Ta=-40 ~ +45℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section) | ||||
| WORKING HUMIDITY | 20 ~ 95% RH non-condensing | |||||
| STORAGE TEMP., HUMIDITY | -40 ~ +80℃, 10 ~ 95% RH | |||||
| TEMP. COEFFICIENT | ±0.03%/℃ (0 ~ 45℃) | |||||
| VIBRATION | 10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes | |||||
| SAFETY & EMC | SAFETY STANDARDS | UL8750,CSA C22.2 No.250.13-12; ENEC BS EN/EN61347-1,BS EN/EN61347-2-13,BS EN/EN62384, GB19510.1, GB19510.14,EAC TP TC 004 approved | ||||
| DALI STANDARDS | Compliance to IEC62386-101, 102, 207 for DA-Type only | |||||
| WITHSTAND VOLTAGE | I/P-O/P:3.75KVAC | I/P-FG:2KVAC | O/P-FG:0.5KVAC | |||
| ISOLATION RESISTANCE | I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH | |||||
| EMC EMISSION | Compliance to BS EN/EN55015, BS EN/EN61000-3-2 Class C (@load ≧60%) ; BS EN/EN61000-3-3, GB17743, GB17625.1,EAC TP TC 020 | |||||
| EMC IMMUNITY | Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11, BS EN/EN61547,light industry level(surge immunity:Line-Earth:4KV, Line-Line:2KV),EAC TP TC 020 | |||||
| OTHERS | MTBF | 346.8Khrs min. MIL-HDBK-217F (25℃) | ||||
| DIMENSION | Refer to mechanical specification | |||||
| PACKING | 0.3Kg; 45pcs/14.5Kg/1.60CUFT | |||||
| NOTE |
| |||||
BLOCK DIAGRAM
DRIVING METHODS OF LED MODULE
This series works in constant current mode to directly drive the LEDs.
Typical output current normalized by rated current (%)
Typical output current normalized by rated current (%) 
3in 1 dimming function (for B-Type)
- Output constant currentlevel can be adjusted by applying one of the three methodologies between DIM+ and DIM-: 1~10VDC, or 10V PWM signal or resistance.
- Direct connecting to LEDs is suggested. Itis not suitable to be used with additional drivers.
- Dimming source current from power supply: 1004A (typ.)
pplying additive 1~ 10VDC
pplying additive 10V PWM signal (frequency range 100Hz ~ 3KHz):
Applying additive resistance:
Note: In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follow, or please contact MEAN WELL for other options.
Using a switch and relay can turn ON/OFF the lighting fixture.
DALI Interface (primary side; for DA-Type) –
- Apply DALIsignal between DA+ and DA-.
- DALI protocol comprises 16 groups and 64 addresses.
- Firststeps fixed at 8% of output.
OUTPUT LOAD vs TEMPERATURE
AMBIENT TEMPERATURE, Ta (C)
STATIC CHARACTERISTIC
INPUT VOLTAGE (V) 60Hz
POWER FACTOR (PF) CHARACTERISTIC
TOTAL HARMONIC DISTORTION (THD)
EFFICIENCY vs LOAD
HBG-100P series possess superior working efficiency that up to 91.5% can be reached in field applications. X 60V Model
LOAD
MECHANICAL SPECIFICATION
Atype
BIDAtype
Documents / Resources
 | MEAN WELL HBG-100P Series Constant Current LED Driver [pdf] User Guide HBG-100P Series Constant Current LED Driver, HBG-100P, Series Constant Current LED Driver, Constant Current LED Driver, Current LED Driver, LED Driver |
