FDHC – 100 series
100W Constant Power Mode LED Driver
Instruction Manual
Features
- Constant Power mode output
- Metal housing design
- Built-in Input OVP (Over Voltage Protection)
- Built-in active PFC function, PF>0.9, THD<10%
- Full Power at 70-100% max. current
- No load power consumption <0.6W
- IP67 rating for indoor or outdoor installations
- Output current adjustable via potentiometer
- 3 years warranty
Applications
- LED flood lighting
- LED decorative lighting
- LED architectural lighting
- LED street lighting
Description
FDHC-100 series is a 100W AC/DC LED power supply featuring the constant power output mode, FDHC-100 operates from 180 295VAC, and output current can be adjusted between 490mA to 1050mA & 1300mA 3000mA. Thanks to the high efficiency of up to 90%, with the fanless design, the entire series is able to operate for -30°C – +90°C case temperature under free air convection. The design of metal housing and IP67 ingress protection level allows this series to fit both indoor and outdoor applications. FDHC-100 is equipped with an output current adjustable function so as to provide optimal design flexibility for the LED lighting system.
Model Encoding
SPECIFICATION
MODEL | FDHC-100L | FDHC-100H | |
OUTPUT |
OUTPUT CURRENT REGION | 490~ 1050mA(700mA default) | 1300~ 3000mA(1850mA default) |
CONSTANT POWER Note.2 | 100W | ||
CONSTANT CURRENT REGION Note.2 | 96 ~ 142V | 30 ~ 54V | |
FULL POWER CURRENT RANGE | 700~ 1050mA | 1850~ 3000mA | |
OPEN CIRCUIT VOLTAGE(max.) | 154V max. | 59V max. | |
CURRENT TOLERANCE | ±5.0% | ||
SET UP TIME Note.3 | 1000ms/230VAC | ||
INPUT |
VOLTAGE RANGE Note.5 | 180 ~ 295VAC (Please refer to the “STATIC CHARACTERISTIC” section) |
|
FREQUENCY RANGE | 47 ~ 63Hz | ||
POWER FACTOR (Typ.) | PF≧0.9(@load≧70%/230VAC; @load≧75%/277VAC) (Please refer to the “POWER FACTOR (PF) CHARACTERISTIC” section) |
||
TOTAL HARMONIC DISTORTION | THD< 10%(@full load/220VAC 50Hz) (Please refer to the “TOTAL HARMONIC DISTORTION(THD)” section) |
||
EFFICIENCY (Typ.) | 90% | ||
AC CURRENT (Typ.) | 0.7A / 230VAC 0.5A/277VAC | ||
INRUSH CURRENT(Typ.) | COLD START 50A(twidth=270μs measured at 50% Speak)/230VAC; Per NEMA 410 | ||
MAX. No. of PSUs on 16A CIRCUIT BREAKER | 9 units (circuit breaker of type B) / 16 units (circuit breaker of type C) at 230VAC | ||
LEAKAGE CURRENT | <0.75mA / 277VAC | ||
NO LOAD POWER CONSUMPTION | <0.6W | ||
PROTECTION |
SHORT CIRCUIT | Hiccup mode recovers automatically after the fault condition is removed | |
OVER TEMPERATURE | Shut down output voltage, recovers automatically after fault condition is removed | ||
INPUT OVP |
305 ~ 315VAC (Shut down output voltage when the input voltage exceeds protection voltage) | ||
295 ~ 305VAC (Auto recovery) | |||
can survive input voltage stress of 440V for 48 hours | |||
ENVIRONMENT |
WORKING TEMP. | Tcase=-30 ~ +90℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section) | |
MAX. CASE TEMP. | Tcase=+90℃ | ||
WORKING HUMIDITY | 20 ~ 95% RH non-condensing | ||
STORAGE TEMP., HUMIDITY | -30 ~ +80℃, 10 ~ 95% RH | ||
TEMP. COEFFICIENT | ±0.03%/℃ (0 ~ 50℃) | ||
VIBRATION | 10 ~ 500Hz, 5G 12min./1 cycle, the period for 72min. each along X, Y, and Z axes | ||
SAFETY & EMC |
SAFETY STANDARDS | EN61347-1,EN61347-2-13 independent, EN62384,IS15885(part 2/ sec.13),IP67 approved | |
WITHSTAND VOLTAGE | I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:1.5KVAC | ||
ISOLATION RESISTANCE | I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH | ||
EMC EMISSION | Compliance to EN55015, EN61000-3-2 Class C (load≧70%) ; EN61000-3-3 | ||
EMC IMMUNITY | Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level(surge immunity: Line-Earth:6KV,Line-Line:3KV) | ||
OTHERS |
MTBF | 1225.4K hrs min. Telcordia SR-332 (Bellcore) 430.9Khrs min. MIL-HDBK-217F (25℃) | |
DIMENSION | 180*53*33mm (L*W*H) | ||
PACKING | 0.625Kg;24pcs /16Kg / 0.8CUFT | ||
NOTE |
1. All parameters NOT specially mentioned are measured at 230VAC input, rated current, and 25℃ of ambient temperature. |
BLOCK DIAGRAM
OUTPUT CURRENT SETTING
※ -I V Operating Area
Output rated current level can be adjusted through a built-in potentiometer
![]() |
![]() |
OUTPUT LOAD vs TEMPERATURE
STATIC CHARACTERISTIC
POWER FACTOR (PF) CHARACTERISTIC
TOTAL HARMONIC DISTORTION (THD)
※ case at 80℃
EFFICIENCY vs LOAD
FDHC-100 series possess superior working efficiency that up to 90% can be reached in field applications.
Tcase at 80℃
AC input voltage drop vs. output current characteristics
AC input voltage drop | 10% | 8% | 5% | 3% |
Io drop | <13% | <11% | <6% | <3% |
NOTE: Output current will return to the rated value within 90ms
MECHANICAL SPECIFICATION
CASE NO.: 261A Unit: mm
◎ Note: Please connect the case to FG for the complete EMC deliverance.
INSTALLATION MANUAL
Please refer to: http://www.meanwell.com/manual.html
User’s Manualhttp://www.meanwell.com.cn/Upload/PDF/LED_EN.pdf
Documents / Resources
![]() |
MEAN WELL FDHC-100 AC-DC LED driver Constant Power Mode [pdf] Instruction Manual FDHC-100, AC-DC LED driver Constant Power Mode, FDHC-100 AC-DC LED driver Constant Power Mode, LED driver Constant Power Mode, driver Constant Power Mode, Constant Power Mode, Power Mode |