Double Printed A4 Leaflet
User Guide
Mode 2 EV Charger 
This Masterplug Mode 2 charger is intended for use with electric and hybrid vehicles.
Please read and use in accordance with these safety instructions. Please retain instructions for reference.
Safety Instructions
Always inspect before use, do not use if the Electric Vehicle Supply Equipment (EVSE) plug, or cable is damaged.
Do not use with an extension lead or adaptor.
Connect the charging cable to a correctly functioning and suitable socket outlet.
Protect the plug and cable from moisture.
The user is responsible for any personal injury or vehicle or property damage arising from inappropriate use.
Operating Instructions & Indicator Status
Follow the instruction on the charger screen.
- Insert 3-pin plug into wall socket (and switch on) – Charger starts self test mode, and Masterplug logo will appear on the screen. After a couple of seconds, LED will flash Blue, ready to connect, if Red check fault guide.
- Connect to EV – the charger will then start communication with the car, indicated by a Yellow LED.
- Charging – Green indicator streams from top to bottom. Once charged indicator will turn solid Green.
- To end charging disconnect (turn off) from wall socket and remove charger from EV.
| Action | Indicator Status | Screen Display | Remark |
| Connect to will socket | |
Start-up Masterplug logo appears Self-test procedure starts | |
| Ready to connect | Blue Flashing ON | PLEASE CONNECT TO THE CAR | Charger connected to wall socket, not to vehicle |
| Connected to EV | Yellow ON |  |
Communication test |
| Charging | Green stream bottom to top |  |
Screen will display Current (Amp), Voltage, temperature and connection time. |
| Fault | Red ON |  |
Power off and disconnect from EV See Fault Guide Error state shown |
Fault Guide & Trouble Shooting
The charger includes many safety features to protect your electric vehicle, a fault is indicated by illumination of the Red indicator.
| Fault State | Remark |
| OVP State | Over voltage, input voltage out of tolerance. |
| UVP State | Under voltage, input voltage out of tolerance. |
| OTP State | Charger over temperature. Turn off power for 30min and allow to cool. |
| POTP State | Plug over temperature. Turn off power for 30min and allow to cool. |
| OCP State | Overload, current set too high. Check EV settings. Max 1 0A. |
| DCLP State | Direct current earth fault. Turn off power and check for damage to the cable. |
| CP Fault | Charging cable fault. CP voltage abnormal. |
| Relay Fault | Charging cable fault. |
| PEN or Earth Fault | Lack of earth connection at wall socket. |
To reset and clear the fault follow the instructions.
Unplug charging cable from the vehicle.
Unplug (or turn off) charging cable from the wall socket.
Keep unplugged for 30 seconds.
Repeat connection process.
If the faults are not reset, the charging cable may be fault. Please contact the retailer, or Masterplug via our helpdesk support team – 03300 249 279 / technical.support@masterplug.com
Technical
Rated CurrenWoltage/Frequency: 1 0A/230V/50Hz
Output: 2.3kW Max
Rated Residual Operating Current: Ian: 30mA, 6mA DC
Operating Temperature: -25° C to +40 ° C
IP Rating: IP66(Control Box)
Standards: EN 62752; EN 61851-1
Care
Masterplug recommend the use of a soft dry or slightly damp cloth periodically to clean the cable and charger body.
Do not use cleaning agents.
Batch Code Explanation
yyWxx Manufacturing date code, year of manufacture (yy) and week of manufacture (Wxx)
Environmental Protection
This symbol is known as the”Crossed-out Wheelie Bin Symbol”.When this symbol is marked on a product or battery, it means that it should not be disposed of with your general household waste. Some chemicals contained within electri cal/electronic products or batteries can be harmful to health and the environment. Only dispose of electrical/electronid battery items in separate collection schemes, which cater for the recovery and recycling of materials contained within.
Your co-operation is vital to ensure the success of these schemes and for the protection of the environment.
Address/Helpline
Luceco PLC Stafford Park 1 Telford TF3 3BD ENGLAND
(EU) Luceco SE C/ Bobinadora 1-5 08302 Matar6 SPAIN
If you have further technical assistance you can get in touch with our Technical Helpline on:
03300 249 279 / technical.support@masterplug.com
Mode 2 EV Charger
www.masterplug.com 
Documents / Resources
 |
Masterplug EVCM22135 Mode 2 EV Charger Double Printed A4 Leaflet [pdf] User Guide EVCM22135 Mode 2 EV Charger Double Printed A4 Leaflet, EVCM22135, Mode 2 EV Charger Double Printed A4 Leaflet, Charger Double Printed A4 Leaflet, Double Printed A4 Leaflet, Printed A4 Leaflet, Leaflet |