Marshall logoCV610-U2 Silver/Black
CV610-UB All Black 
Full HD USB 2.0 PTZ Camera
Operating Instructions
Version V3.6

Marshall CV610-U2 Full HD USB 2.0 PTZ Camera

Akuvox X915X IP Touchscreen Smart Door - Warning IMPORTANT SAFETY INSTRUCTIONS:

  • Remove lens cover before plugging the camera into the power source.
  •  Before starting operation, please fully read and follow all instructions in the manual. For your safety, always keep this manual with the camera for reference.
  • The camera power input range is 100-240VAC (50-60Hz), ensure the power supply input is within this range before powering on.
  • The camera power voltage is 12VDC, the rated currency is 1.5A. We suggest you use it with the original power supply adapter supplied in the box.
  • Please keep the power cable, video cable and control cable in a safe place. Protect all cables especially the connectors from moisture and dirt.
  • Operational environment: 32ºF to 122ºF ( 0ºC to 50ºC) and humidity less than 90%. To avoid any danger, do not put anything inside the camera, and keep away from corrosive liquids.
  • Avoid stress, vibration, and jolts during transportation, storage, and installation.
  • Do not detach the camera housing and cover. For any service, please contact authorized technicians.
  • RF cable and control cable should be individually shielded, and cannot be substituted with other cables. Do not direct the camera lens towards strong light, such as the sun or the intensive light.
  • Always use a dry, soft cloth to clean the camera housing. Only use neutral cleaning agents when there is need to clean smudges or dirt from the camera body. To avoid damage on the camera lens, only use a soft microfiber cloth.
  • Do not carry or move the camera by holding the camera head. To avoid mechanical damage of internal gears, do not rotate the camera head by hand.
  • Put the camera on a fixed desk or platform, avoid installing on surfaces that are not level.
  • Power Supply Polarity (Drawing) below:

Marshall CV610-U2 Full HD USB 2.0 PTZ Camera -Drawing

INCLUDED IN THE BOX

  1. Power Adapter
  2. CV610-U2-WM – Wall Mount
  3. Power Cable
  4. RS232 Control Cable
  5. USB2.0 Cable
  6. Remote Controller (battery not included)
  7. Main Camera

QUICK START

  1. REMOVE Lens Cover and check all cable connections to be sure they are all firmly connected before powering on
  2. Marshall CV610-U2 Full HD USB 2.0 PTZ Camera -powering onDial Switch Setting (at the bottom of the camera):Marshall CV610-U2 Full HD USB 2.0 PTZ Camera -Dial Switch Setting
DIP Switch (ARM)
SW-1 SW-2 Instruction
1 OFF OFF Updating mode
2 ON OFF Debugging mode
3 OFF ON Undefined
4 ON ON Working mode

 

DIP Switch (IR CODE TYPE)
SW-3 SW-4 Instruction
1 OFF OFF Off(Close IR receiver)
2 ON OFF Undefined
3 OFF ON SEJIN 4PPM CODE
4 ON ON NEC CODE(standard)

 

DIP Switch (USB)
SW-5 SW-6 Instruction
1 OFF OFF Undefined
2 ON OFF Working mode
3 OFF ON Updating mode
4 ON ON Undefined

Note: Normal Working Mode: SW-1~5: ON, SW-6: OFF

PRODUCT HIGHLIGHTS

  • Compact, ergonomically designed housing perfect for small huddle rooms or locations
  •  Supports advanced Ambarella DSP, 1/2.8 inch 5MP image sensor, and high quality 10X 62.5 degree
    FOV optical lens, provides crystal clear image quality
  • Fast switching between different video formats: less than 1 second
  • 10X Optical Zoom + 12X Digital Zoom
  • Fast and accurate focus performance
  • Easy firmware upgrade – (field-upgradable)
  • USB2.0 high-speed output
  • Effective RS232/485 serial control. Up to 128 presets
  • Compatible with the majority of videoconferencing software (UVC1.5 protocol standard)
  • The camera comes with an accurate IR Remote Control unit
  • IR transfer/IR pass function: excepts signals from other codec’s and IR remote control signals

CV610-U2 SPECIFICATIONS

Video Format MJPG – 1080P30, 720P30, 640*480P30
Video Port USB2.0
Sensor 1/2.8 inch high-quality 5MP CMOS sensor
Lens F4.7-47.mm(10X), F1.8 – 14, Field of view: 62.5°(wide)-6.43°(tele)
Pankilt Rotation Pan:±170°; Tilt:-30°-+90°, support up-side-down installation
Pan/tilt Speed Pan: 0.1°-1207s; Tilt: 0.1°-80°/s
Preset 10 via IR remote setting, 128 via VISCA control, preset accuracy:0.1°
Control Port RS232, RS485, USB2.0
Min. Lux 0.01Iux
White Balance Auto/Manual
Focus Auto/Manual
Iris Auto/Manual
Shutter Auto/Manual
WDR Supported
BLC Supported
2D Noise Reduction Supported
3D Noise Reduction Supported
Input Voltage DC12V
Dimension 148mmx132mmx161mm
Net weight 0.9KG (2LBS)

RESOLUTION & FRAME RATE SETTINGS

The Marshall CV610-U2 acts as a UVC command slave to Teleconference, U.C. or Video Capture Software programs that use it as a USB capture device. Once selected as an available camera, these software platforms send commands to the camera as to compatible resolutions and frame rates based on bandwidth, software parameters, and/or computer capabilities. Some software platforms allow for direct adjust commands to change resolution and frame rates, such as VLC Player and others. CV610-U2 adjusts as commanded by the software platform or to the nearest resolution settings available (1080p, 720p, 480p). There is no way to manually adjust resolutions and frame rates from the camera or camera OSD menu since it relies on UVC (USB video class) commands. CV610-U2 adheres to UVC1.5 protocol standards.

CAMERA INTERFACE

Marshall CV610-U2 Full HD USB 2.0 PTZ Camera -CAMERA INTERFACE

  1. Camera Lens
  2.  Camera Base
  3. IR Receiver Panel
  4. Indicator Light
  5. Dial Switch
  6. Tripod Screw Hole
  7. Installation Hole
  8. RS232 (VISCA IN) Port
  9. USB2.0 Port
  10. DC12V Power Input
  11.  Power Indicator light (red)

CAMERA DIMENSIONS (mm)

Marshall CV610-U2 Full HD USB 2.0 PTZ Camera - CAMERA DIMENSIONS (mm)

IR REMOTE CONTROLLER

Marshall CV610-U2 Full HD USB 2.0 PTZ Camera -IR REMOTEMarshall CV610-U2 Full HD USB 2.0 PTZ Camera - LED Function

LED Function Instruction
FOCUS
Press any button and shows in red color: Current selection is to control CAM1;
Press any button and shows in green color: Current selection is to control CAM2;
Press any button and shows in blue color: Current selection is to control CAM3;
CAM1/CAM2/CAM3:
Long press(3seconds) to set camera address;
Short press to select camera address to control.
Focus: +/-
Manual focus, only valid under manual focus mode;
Zoom: +/-
Control the lens zoom rate;
Navigate : Up/Down/Left/Right
In normal working mode, use navigate key to control pan/tilt;
Or enter the OSD menu, use navigate key to set parameters.
Confirm/Home button:
In normal working mode, short press to let the camera go back to the home position

Menu Button: Enter the OSD menu

Marshall CV610-U2 Full HD USB 2.0 PTZ Camera -Menu Button

Number buttons
Set Preset: Long press(3seconds) the number button to save preset;
Clear Preset: +number button to clear the relative preset;
Long press(3seconds) the Clear button to clear all preset;
Short press 3 times to reset the lens focus;
Run Preset: Short press the number button to run the relative preset.

Marshall CV610-U2 Full HD USB 2.0 PTZ Camera - Number buttons

Short press to power on or off the camera
Power symbol

CV610-U2 OSD MENU EXPLAINED

  1. Once the camera is powered up and working, press themenu Menu button on the IR remote control to enter the OSD menu (see pic.1); once changes are made press the OSD menu button again to exit and save Modi ed parameters. Marshall CV610-U2 Full HD USB 2.0 PTZ Camera - menu
  2. Use the navigation buttons (up/down/left/right) to choose which function to select. As picture 1 shows, once the selection is made, the selected option will change to a gray background highlight. Press the right navigation button to go to the submenu (see pic.2). Marshall CV610-U2 Full HD USB 2.0 PTZ Camera - navigate buttons
  3. In the submenu, once again press the up/down navigation buttons to scroll and select, use the left/right navigation button to cycle through selection options parameters.
  4. Select the last option “RETURN” and press the left navigation button to get back to the main menu or previous menu.
  5. Press the OSD buttonmenu again to exit the menu.
  6. The following pages outline the Menu structure as it appears in OSD Menu:
Camera Set PROTOCOL VISCAIRELCO-P/PELCO-D
ADDRESS 1-7
BAUD RATE 2400.9600.115200
PARITY BIT NONE
STANDBY MODE (ON/CFF )
RETURN Back to the main menu
FOCUS FOCUS MODE AUTO/MANUAL/PUSH
SENSITIVITY LOW/MID/HIGH
D_ZOOM OFF/ON
ZOOM SPEED 0-7
LENS INIT OFF/5K/10K/151(1201(/EXE
DIS ZOOM RATIO OFF/ON
RETURN Back to the main menu
WB MODE WB MODE ATVVB/GAIN/TEMPISOD./FLJAWB/IDRIODR./PUSH
B GAIN VVB MODE 0-255 (Only Valid when WB MODE set to GAIN or TEMP.)
R_GAIN 0-255 (Only Valid when WB MODE set to GAIN or TEMP.)
RETURN Back to the main menu
EXPOSURE EXP MODE AUTO/MANUAUIRIS/SHUT/BRI.
SHUT TIME Shutter time: 1/1-1/10K
(Valid when EXP MODE set to MANUAL or SHUT)
IRIS Iris value: 0-13
(Valid when EXP MODE set to MANUAL or IRIS)
AGE Gain value: 04B-15dB
(Valid when EXP MODE set to MANUAL)
BRIGHT Brightness value: 0-27 (Valid when EXP MODE set to BRI.)
SLOW SHUT OFF/ON
FLICK OFF/50HZ/60HZ
(Valid when EXP MODE set to AUTO or IRIS)
RETURN Back to the main menu
IMAGE
ENHANCE
2D NR OFF/ON
3D NR OFF/AUTO/ 1-4
D_VVDR OFF/1-6
GAMMA
0 -4
BACKLIGHT OFF/ON
HIGHLIGHT OFF/ON
RETURN Back to the main menu
MASK MASK SWITCH ON/OFF
COLOR WHITE/YELLOW/GRAY/GREENNIOLET/RED
INDEX 1-8
INDEX SWITCH OFF/ON
ROW START 0-1919
ROW END 1-1920
LINE START 0-1079
LINE END 1-1079
RETURN Back to the main menu
D/N MODE D/N MODE DAY/NIGHT/AUTO
DAY TO NIGHT 15-126
NIGHT TO DAY 5-190
SWITCH DELAY 1-60
GAIN LIMIT 2-511
RETURN Back to the main menu
CAMERA
INFO
IMAGE VER. PC-V0.0.6 (change without notice)
IMAGE DATE 16.10.20 (change without notice)
CONTROL VER. UC V0.1.4 (change without notice)
CONTROL DATE 17.01.07 (changes without notice)
BAUDRATE 9600
PARITY BIT NONE
RETURN Back to the main menu
  1. All Button Sending Mode: long press (3seconds) the Menu+ number “3” button simultaneously, the remote will enter all button sending mode.
  2. Similar operation for the TV control mode learning.

Marshall CV610-U2 Full HD USB 2.0 PTZ Camera - VISCA IN

No. Function
1 DTR
2 DSR
3 TXD
4 GND
5 RXD
6 A
7 IR OUT
8 B
VISCA IN &RS485 Connection
Camera VISC RS485
1 DTR
2 DSR
3 TXD
4 GND
5 RXD
6 A(+) TX+
7 IR OUT
8 B(-) TX-
VISCA IN 8089 Connection
Camera VISCA IN Windows DB-9
1 DTR 6 DSR
2 DSR 4 DTR
3 TXD 2 RXD
4 GND 5 GND
5 RXD 3 TXD
6 A(+)
7 IR OUT
8 6(-)

SERIAL PORT CONFIGURATION:

Parameter Value Parameter Value
Baud rate 2400/9600/115200 Stop Bit lbit
Start Bit 1 bit Verify Bit None
Date Bit 8 bit

VISCA PROTOCOL

Part 1 – Camera Return Command

Ack/Completion Message
Command Packet Note
ACK z0 41 FF Returned when the command is accepted.
Completion z0 51 FF Returned when the command has been executed.
Error Messages
Command Packet Note
Syntax Error z0 60 02 FF Returned when the command format is different or when a command with illegal  command parameters is accepted
Command Not
Executable
z0 61 41 FF Returned when a command cannot be executed due to current conditions. For  example, when commands controlling the  focus manually are received during auto
focus.

Part 2 – Camera Control Command

Command Formation Command Packet Note
AddressSet Broadcast 88 30 01 FF Address setting
IF_Clear Broadcast 88 01 00 01 FF I/F Clear
CAM_Power On 8x 01 04 00 02 FF Power ON/OFF
Off 8x 01 04 00 03 FF
CAM_Zoom Stop 8x 01 04 07 00 FF
Tele(Standard) 8x 01 04 07 02 FF
Wide(Standard) 8x 01 04 07 03 FF
Tele(Variable) 8x 01 04 07 2p FF p 0(low)-7(high)
Wide(Variable) 8x 01 04 07 3p FF
Direct 8x 01 04 47 Op Oq Or Os FF pqrs: Zoom Position (0(wide) -0x4000(tele))
CAM_Focus Stop 8x 01 04 08 00 FF
Far(Standard) 8x 01 04 08 02 FF
Near(Standard) 8x 01 04 08 03 FF
Direct 8x 01 04 48 Op Oa Or Os FF pgrs: Focus Position
One Push AF 8x 01 04 18 01 FF
CAM_ZoomFocus Direct 8x 01 04 47 Op Oq Or Os Ot Ou Ov Ow FF pqrs: Zoom Position (0(wide)- Ox4000(tete)) tuvw: Focus Position
CAMWB Auto 8x 01 04 35 00 FF
Indoor 8x 01 04 35 01 FF
Outdoor 8x 01 04 35 02 FF
OnePush 8x 01 04 35 03 FF
Manual 8x 01 04 35 05 FF
Outdoor Auto 8x 01 04 35 06 FF
Sodium Lamp Auto 8x 01 04 35 07 FF
Sodium Auto 8x 01 04 35 08 FF
CAM_RGaln Reset 8x 01 04 03 00 FF Manual Control of R Gain
Up 8x 01 04 03 02 FF
Down 8x 01 04 03 03 FF
Direct 8x 01 04 43 00 00 Op Oq FF pq: R Gain’ (0-0xFF)
Command Fonnation Command Packet Note
CAM_Bgain Reset 8x 01 04 04 00 FF Manual Control of B Gain
Up 8x 01 04 04 02 FF
Down 8x 01 04 04 03 FF
Direct 8x 01 04 44 00 00 Op Oq FF pq: B Gain (0-0xFF)
CAM AE Full Auto 8x 01 04 39 00 FF Automatic Exposure mode
Manual 8x 01 04 39 03 FF Manual Control mode
Bright 8x 01 04 39 OD FF Bright mode(Manual control)
CAM Shutter Reset 8x 01 04 OA 00 FF Shutter Setting
Up 8x 01 04 OA 02 FF
Down 8x 01 04 OA 03 FF
Direct 8x 01 04 4A 00 00 Op Oq FF pq: Shutter Position (0-0x15)
CAM Iris
Reset 8x 01 04 OB 00 FF Iris Setting
Up 8x 01 04 OB 02 FF
Down 8x 01 04 OB 03 FF
Direct 8x 01 04 4B 00 00 Op Oq FF pq: Iris Position (0- Ox11)
CAM Gain
_
Reset 8x 01 04 OC 00 FF Gain Setting
Up 8x 01 04 OC 02 FF
Down 8x 01 04 OC 03 FF
Direct 8x 01 04 OC 00 00 Op Oq FF pq: Gain Positon (0-0x0E)
CAM Bright Reset 8x 01 04 OD 00 FF Bright Setting
Up 8x 01 04 OD 02 FF
Down 8x 01 04 OD 03 FF
Direct 8x 01 04 4D 00 00 Op Oq FF pq: Bright I Positon 0
CAM_WDR On 8x 01 04 3D 02 FF WDR ON/OFF
OR 8x 01 04 3D 03 FF
Direct 8x 01 04 D3 Op FF pq: WDR Position (1-0x06)
CAM Backlight On 8x 01 04 33 02 FF BackLight On
OR 8x 01 04 33 03 FF BackLight OR
CAM_Aperture Reset 8x 01 04 02 00 FF Aperture Control
Up 8x 01 04 02 02 FF
Down 8x 01 04 02 03 FF
Direct 8x 01 04 42 00 00 Op Oq FF pq: Aperture Gain (0-0x04)
CAM Memory Reset 8x 01 04 3F 00 Op FF p: Memory Number (=0 to 127) Corresponds to 0 to 9 on the Remote Commander
Set 8x 01 04 3F 01 Op FF
Recall 8x 01 04 3F 02 Op FF
CAM_LR_Reverse On 8x 01 04 61 02 FF Image Flip Horizontal ON/OFF
OR 8x 01 04 61 03 FF
CAM_PictureFlip On 8x 01 04 66 02 FF Image Flip Vertical ON/OFF
Off 8x 01 04 66 03 FF
CAM_ColorGain Direct 8x 01 04 49 00 00 00 Op FF (0-0x0E)
CAM_2D Noise Reduction Direct 8x 01 04 53 Op FF 0::OFF 1:0N
Command Funnation Command Packet Note
CAM_3D
Noise Reduction
Direct 8x 01 04 54 Op FF O:OFF 1: AUTO 2-5: LEVEL
FLICK 50HZ 81 01 04 23 01 FF
60HZ 81 01 04 23 02 FF
Freeze Freeze On 81 01 04 62 02 FF Freeze On Immediately
Freeze Off 81 01 04 62 03 FF Freeze OR Immediately
Preset Freeze On 81 01 04 62 22 FF Freeze On When Running Preset
Preset Freeze OR 81 01 04 62 23 FF Freeze OR When Running Preset
IR_Transfer Transfer On 8x 01 06 1A 02 FF Receive IR(remote commander) CODE from VISCA communication ON/OFF
Transfer Off 8x 01 06 lA 03 FF
Pan_tiltDrive Up 8x 01 06 01 VV WW 03 01 FF W: Pan Weed 0z01 (low speed) to 0x 18 (high speed)
WW lilt speed Ox01 (low speed) to Ox14 (high speed)
YYVY: Pan Position(TBD)
ZZZZ. Tit Position(TBD)
Down 8x 01 06 01 VV VVW 03 02 FF
Left 8x 01 06 01 VV VVW 01 03 FF
Right 8x 01 06 01 VV VIM 02 03 FF
Upleft 8x 01 06 01 N/V WW 01 01 FF
Upright 8x 01 06 01 N/V WW 02 01 FF
DownLeft 8x 01 06 01 VV VVW 01 02 FF
DownRight 8x 01 06 01 VV VVW 02 02 FF
Stop 8x 01 06 01 W WW 03 03 FF
AbsolutePosition 8x 01 06 02 W WW
OY OY OY OY OZ OZ OZ OZ FF
RelativePosition 8x 01 06 03 W WW
OY OY OY OY OZ OZ OZ OZ FF
Home 8x 01 06 04 FF
Reset 8x 01 06 05 FF
Pan-tiltLimitSet Set 8x 01 06 07 00 OW
OY OY OY OY OZ OZ OZ OZ FF
W.1 UpRight 0:DownLeft

YYVY: Pan Limit Position(TBD)
ZZZZ. Tilt Limit Position(TBD)
Clear 8x 01 06 07 01 OW
07 OF OF OF 07 OF OF OF FF

Part 3 – Inquiry Command

Command Command Packet Return Packet Note
CAM_Powering 8x 09 04 00 FF y0 50 02 FF On
y0 50 03 FF Off(Standby)
CAM_ZoomPosing 8x 09 04 47 FF y0 50 Op Oq Or Os FF pgrs: Zoom Position
CAM_FocusModelng 8x 09 04 38 FF y0 50 02 FF
Auto Focus
y0 50 03 FF Manual Focus
CAM_FocusPosing 8x 09 04 48 FF y0 50 Op Oq Or Os FF pqrs: Focus Position
CAM_WBModeIng 8x 09 04 35 FF y0 50 00 FF Auto
y0 50 01 FF Indoor mode
y0 50 02 FF
Outdoor mode
y0 50 03 FF OnePush mode
y0 50 04 FF ATW
y0 50 05 FF Manual
CAM_RGainIng 8x 09 04 43 FF y0 50 00 00 Op Oq FF pq: R Gain
CAM_BGalnIng 8x 09 04 44 FF y0 50 00 00 Op Oq FF pq: B Gain
CAM_AEModelng 8x 09 04 39 FF y0 50 00 FF Full Auto
y0 50 03 FF Manual
y0 50 OA FF Shutter priority
y0 50 OB FF Iris priority
y0 50 OD FF Bright
CAM_ShutterPosIng 8x 09 04 4A FF y0 50 00 00 Op Oq FF pq: Shutter Position
CAM_IrisPosing 8x 09 04 4B FF y0 50 00 00 Op Oq FF pq: Iris Position
CAM_GainPosling 8x 09 04 4C FF y0 50 00 00 Op Oq FF pq: Gain Position
CAM_ BrIghtPosfing 8x 09 04 4D FF y0 50 00 00 Op Oq FF pq: Bright Position
CAM_ExpCompModelng 8x 09 04 3E FF y0 50 02 FF
On
y0 50 03 FF Off
CAM_ExpCompPosIng 8x 09 04 4E FF y0 50 00 00 Op Oq FF pq: ExpComp Position
CAM_Apertureing 8x 09 04 42 FF y0 50 00 00 Op Oq FF pq: Aperture Gain
CAM_MemoryIng 8x 09 04 3F FF y0 5Opp FF pp: Memory number last operated.
SYS_MenuModelng 8x 09 06 06 FF y0 50 02 FF On
y0 50 03 FF Off
CAM_LR_ReverseIng 8x 09 04 61 FF y0 50 02 FF
On
y0 50 03 FF Off
CAM_PIctureFlIpIng 8x 09 04 66 FF y0 50 02 FF On
y0 50 03 FF Off
CAM_IDIng 8x 09 04 22 FF y0 50 Op Oq Or Os FF pqrs: Camera ID
CAM_VerslonIng 8x 09 00 02 FF y0 50 ab cdmn pq rs to vw FF
IR_Transter 8x 09 06 1A FF y050 02 FF
On
y0 50 03 FF Off
Pan411tMaxSpeedIng 8x 09 06 11 FF y0 50 ww zz FF v: PanMaxSpeecl zz: lilt Max Speed
Pan4MPosIng 8x 09 06 12 FF y0 50 Ow Ow Ow Ow Oz Oz Oz Oz FF %WON: PanPosition znz• Tilt Position

Note: (x) means the camera address; (y)=(x + 8).

Pan Angle VISCA Value lilt Angle VISCA Value
-170 0xF670 -30 OxFE50
-135 0xF868 0 Ox0000
-90 OxFAFO 30 Ox0 I BO
-45 OxFD78 60 0x0360
0 0x0000 90 Ox510
45 Ox0288
90 0x0510
135 Ox0798
170 0x0990
Pan(deqree/second) lilt(decree/second)
0 0.3 0 3
1 1 1 1
2 2. 2 2.
3 2. 3 2.
4 2. 4 4.
5 3. 5 5.
6 3. 6 6
7 3.0 7 8
8 3. 8 10
9 3. 9 12
10 4. 10 15
11 5. 11 18
12 6 12 23
13 9 13 30
14 15 14 39
15 19 15 48
16 25 16 59
17 32 17 69
18 38 18 80
19 45
20 58
21 75
22 88
23 105
24 120
Shutter
speed
60/30mode 50/25mode Iris
21 1/10000 1/10000 0 close
20 1/6000 1/6000 1 F14
19 1/4000 1/3500 2 F11
18 1/3000 1/2500 3 F0,10.
17 1/2000 1/1750 4 F8
16 1/1500 1/1250 5 F0,7.
15 1/1000 1/1000 6 F0,6.
14 1/725 1/600 7 F0,5.
13 1/500 1/425 8 F4
12 1/350 1/300 9 F0,3.
11 1/250 1/215 10 F0,3.
10 1/180 1/150 11 F0,2.
9 1/125 1/120 12 F2
8 1/100 1/100 13 F0,2.
7 1/90 1/75
6 1/60 1/50
5 1/30 1/25
4 1/15 1/12
3 1/8 1/6
2 1/4 1/3
1 1/2 1/2
0 1/1 1/1
Gain 0 0dB Gain 8 16dB
1 2dB 9 18dB
2 4dB 10 20dB
3 6dB 11 22dB
4 8dB 12 24dB
5 10dB 13 26dB
6 12dB 14 28dB
7 14dB 15 30dB

IR TRANSFER (IR PASS)

  1. Currently the camera support NEC code format. For customization with other codes, please contact us.
  2. Once the camera finish power configuration, enable the IR transfer function via sending COM command.
  3. Get the targeted remote controller point to the camera IR receiver, press keys on the remote controller. then the camera will output the received IR code via the VISCA IN port.
  4. IR Transfer output format: XX XX XX XX FF
    XX XX XX XX: Remote Controller Code FF: End Code
  5. The camera can save all settings, no need to re-set after the power circle.

UVC CONTROL

Control Requests Control Selector
1 Brightness Control PU_BRIGHTNESS_CONTROL
2 Contrast Control PU_CONTRAST_CONTROL
3 Hue Control PU_HUE_CONTROL
4 Saturation Control PU_SATURATION_CONTROL
5 Sharpness Control PU_SHARPNESS_CONTROL
6 Gamma Control PU_GAMMA_CONTROL
7 White Balance Temperature Control PU_WHITE_BALANCE_TEMPERATURE_CONTROL
8 Gain Control PU_GAIN_CONTROL
9 Power Line Frequency Control PU_POWER_LINE_FREQUENCY_CONTROL
10 Zoom (Absolute) Control CT_ZOOM_ABSOLUTE_CONTROL
11 Zoom (Relative) Control CT_ZOOM_RELATIVE_CONTROL
12 PanTilt (Absolute) Control CT_PANTILT_ABSOLUTE_CONTROL
13 PanTilt (Relative) Control CT_PANTILT_RELATIVE_CONTROL

Wall Mount Installation

  1. Secure the CV610-U2-WM to the wall with 4 M4 screws (included).Marshall CV610-U2 Full HD USB 2.0 PTZ Camera - Wall
  2. Disconnect all cables from the camera. Align the CV610-U2 camera’s ¼-20UNC tripod screw hole with the wall mount screw hole. Use the ¼-20UNC screw (included) to secure the camera onto the wall mount. Reconnect the cables after mounting the camera.
    Note: Do not mount the camera upside down, as the image will be displayed upside down.Marshall CV610-U2 Full HD USB 2.0 PTZ Camera - Wall Mount

Tel: (800) 800-6608 / (310) 333-0606 • Fax: 310-333-0688
www.marshall-usa.com
[email protected]

Leave a comment

Your email address will not be published.