Zebra MC3300x Regulatory Guide

User Information

For information on the MC3300X, refer to the MC3300X Mobile Computer User Guide. Available at: www.zebra.com/support.

Regulatory Information

This device is approved by Zebra Technologies Corporation.

Model Number: MC330L.

Zebra devices are designed to comply with rules and regulations in their sales locations and will be labeled as required.

Local language translations are available at: www.zebra.com/support.

Unauthorized modifications to Zebra equipment may void the user's authority to operate the equipment.

Declared maximum operating temperature: 50°C.

Caution: Only use Zebra approved and UL Listed accessories, battery packs, and battery chargers.

Caution: Do NOT attempt to charge damp/wet mobile computers or batteries. Ensure all components are dry before connecting to an external power source.

Bluetooth® Wireless Technology

This is an approved Bluetooth® product. For more information or to view the End Product Listing, please visit www.bluetooth.org/tpg/listings.cfm.

Country Roaming

This device incorporates the International Roaming feature (IEEE802.11d), ensuring operation on correct channels for the country of use.

Wi-Fi Direct

Operation is limited to the following channels/bands as supported in the country of use:

• Channels 1 - 11 (2412 - 2462 MHz)
• Channels 36 - 48 (5150 - 5250 MHz)
• Channels 149 - 165 (5745 - 5825 MHz)

Frequency of Operation

FCC and IC (5 GHz Only)

Caution: The device for the band 5150-5250 MHz is for indoor usage only to reduce potential interference to co-channel mobile satellite systems. High power radars are allocated as primary users of 5250-5350 MHz and 5650-5850 MHz and could cause interference and/or damage to LE-LAN devices.

AVERTISSEMENT: Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux. Les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.

2.4 GHz Only

The available channels for 802.11 b/g operation in the US are Channels 1 to 11. The range of channels is limited by firmware.

Warranty

For the complete Zebra hardware product warranty statement, go to: www.zebra.com/warranty.

Service Information

Before using the unit, it must be configured for your facility's network and applications. For issues, contact your facility's Technical or Systems Support. They will contact Zebra Global Customer Support at www.zebra.com/support.

For the latest version of this guide, go to: www.zebra.com/support.

Software Support

Zebra ensures customers have the latest entitled software for peak device performance. To confirm, visit www.zebra.com/support. Check Support > Products, or search for the device and select Support > Software Downloads.

If your device does not have the latest entitled software as of purchase date, email Zebra at entitlementservices@zebra.com with the following information:

• Model number
• Serial number
• Proof of purchase
• Title of the software download requested

Zebra will email a link to download the appropriate software if your device is entitled.

Health and Safety Recommendations

Ergonomic Recommendations

Caution: To avoid or minimize ergonomic injury risk, follow these recommendations. Consult your Health & Safety Manager.

• Reduce or eliminate repetitive motion.
• Maintain a natural position.
• Reduce or eliminate excessive force.
• Keep frequently used objects within easy reach.
• Perform tasks at correct heights.
• Reduce or eliminate vibration.
• Reduce or eliminate direct pressure.
• Provide adjustable workstations.
• Provide adequate clearance.
• Provide a suitable working environment.
• Improve work procedures.

Vehicle Installation

RF signals may affect improperly installed or shielded electronic systems in motor vehicles. Consult the manufacturer or representative regarding your vehicle and any added equipment.

Airbags inflate with great force. DO NOT place objects, including wireless equipment, in the airbag deployment area. Improper installation can result in serious injury.

Position the device within easy reach, allowing access without taking eyes off the road.

Note: Connecting to an alert device that causes a vehicle horn to sound or lights to flash on public roads is not permitted.

Important: Before installing or using, check state and local laws regarding windshield mounting and equipment use.

For Safe Installation

• Do not place the phone where it obstructs the driver's vision or interferes with vehicle operation.
• Do not cover an airbag.

Safety on the Road

Do not take notes or use the device while driving. Driving is your first responsibility; give it full attention. Check and obey wireless device laws and regulations in your driving areas.

Warnings for Use of Wireless Devices

Caution: Please observe all warning notices regarding wireless device usage.

Potentially Hazardous Atmospheres – Vehicles Use

Observe restrictions on radio device use in fuel depots, chemical plants, etc., and areas where air contains chemicals or particles (e.g., grain, dust, metal powders) or where you would normally be advised to turn off your vehicle engine.

Safety in Aircraft

Switch off your wireless device when instructed by airport or airline staff. Consult airline staff regarding the use of 'flight mode' or similar features during flight.

Safety in Hospitals

Wireless devices transmit radio frequency energy and may affect medical electrical equipment. Switch off wireless devices in hospitals, clinics, or healthcare facilities as requested to prevent interference with sensitive medical equipment.

Pacemakers

Pacemaker manufacturers recommend maintaining a minimum of 15 cm (6 inches) between a handheld wireless device and a pacemaker to avoid potential interference. These recommendations are consistent with independent research.

Persons with Pacemakers:

• Should ALWAYS keep the device more than 15 cm (6 inches) from their pacemaker when turned ON.
• Should not carry the device in a breast pocket.
• Should use the ear furthest from the pacemaker to minimize potential interference.
• If suspecting interference, turn OFF the device.

Other Medical Devices

Consult your physician or the medical device manufacturer to determine if your wireless product may interfere with the medical device.

RF Exposure Guidelines

Safety Information

Reducing RF Exposure: Use Properly. Only operate the device according to instructions.

International

The device complies with internationally recognized standards for human exposure to electromagnetic fields from radio devices. For information on 'International' human exposure, refer to the Zebra Declaration of Conformity (DoC) at www.zebra.com/doc.

For further information on RF energy safety, see www.zebra.com/responsibility.

Europe

Handheld Devices

This device was tested for typical body-worn operation. Use only Zebra tested and approved belt clips, holsters, and similar accessories to ensure EU Compliance.

US and Canada

Co-located statement

To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must not be co-located or operating in conjunction with any other transmitter/antenna except those already approved in this filing.

Handheld Devices

This device was tested for typical body-worn operation. Use only Zebra tested and approved belt-clips, holsters, and similar accessories to ensure FCC Compliance. Use of third-party accessories may not comply with FCC RF exposure compliance requirements and should be avoided.

Laser Devices

Class 2 laser scanners use a low power, visible light diode. Avoid staring directly into the light beam, as with any bright light source. Momentary exposure to a Class 2 laser is not known to be harmful.

Caution: Use of controls, adjustments, or procedures other than those specified herein may result in hazardous laser light exposure.

Scanner Labeling

ZEBRA TECHNOLOGIES CORP. HOLTSVILLE, NY 11742

MODEL: MC330K / X.XV X.XA

LASER LIGHT - DO NOT STARE INTO BEAM. CLASS 2 LASER PRODUCT.

LASERLICHT - NICHT IN DEN STRAHL BLICKEN. LASER KLASSE 2.

LUMIÈRE LASER - NE PAS REGARDER DANS LE FAISCEAU. APPAREIL À LASER DE CLASSE 2.

630-680nm, 1mW

MC33XX-G

COMPLIES WITH 21CFR1040.10 AND 1040.11 EXCEPT FOR DEVIATIONS PURSUANT TO LASER NOTICE NO. 50, DATED JUNE 24, 2007 AND IEC/EN 60825-1:2014

CAUTION- CLASS 2 LASER LIGHT WHEN OPEN. DO NOT STARE INTO THE BEAM.

ATTENTION- LUMIÈRE LASER DE CLASSE 2 EN CAS D'OUVERTURE. NE PAS REGARDER DANS LE FAISCEAU.

VORSICHT-LASERLICHT KLASSE 2, WENN ABDECKUNG GEOFFNET. NICHT IN DEN STRAHL BLICKEN.

MC33XX-R/S Labels Read:

1. LASER LIGHT - DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT.
2. CAUTION - CLASS 2 LASER LIGHT WHEN OPEN. AVOID DIRECT EYE EXPOSURE.
3. COMPLIES WITH 21CFR1040.10 and 1040.11 EXCEPT FOR DEVIATIONS PURSUANT TO LASER NOTICE NO. 50, DATED JUNE 24, 2007 and IEC 60825-1 (Ed.2.0), EN 60825-1:2007 and/or IEC/EN 60825-1:2014.

LED Devices

Classified as 'EXEMPT RISK GROUP' according to IEC 62471:2006 and EN 62471:2008.

Pulse duration: 1.7 ms for MC330L Terminal with SE4750.

Pulse duration: 4 ms for MC330L Terminal with SE4770.

Pulse duration: 4 ms for MC330L Terminal with SE4720.

Pulse duration: Continuous Wave for MC330L Terminal with SE4850.

Power Supply

Use ONLY a Zebra approved Nationally Recognized Test Laboratory (NRTL) Certified ITE (LPS/SELV) power supply with electrical ratings: Output 5.4 VDC, min 1.8 A, with a maximum ambient temperature of at least 50°C. Use of alternative power supply will invalidate any approvals and may be dangerous.

Batteries

Taiwan - Recycling

EPA requires battery producing or importing firms to indicate recycling marks on batteries used in sales, giveaway, or promotion, per Article 15 of the Waste Disposal Act. Contact a qualified Taiwanese recycler for proper battery disposal.

Battery Information

Caution: Risk of explosion if battery is replaced by an incorrect type. Dispose of batteries according to instructions.

Use only Zebra approved batteries. Approved battery models for charging capability:

• Part Number BT-000337 (3.7 VDC, 5,200 mAh)
• Part Number BT-000338 (3.7 VDC, 2,740 mAh)
• Part Number BT-000375 (3.7 VDC, 7,000 mAh)

Zebra approved rechargeable battery packs are designed to high industry standards. However, battery life is limited by factors like heat, cold, harsh conditions, and drops.

Storing batteries for over six months may cause irreversible deterioration. Store batteries at half charge in a dry, cool place, removed from equipment, to prevent capacity loss, rusting, and electrolyte leakage. For storage over one year, verify charge level annually and recharge to half capacity.

Replace the battery when significant run time loss is detected.

Standard warranty for all Zebra batteries is one year. For more information on Zebra batteries, visit: www.zebra.com/batterybasics.

Battery Safety Guidelines

Ensure the charging area is clear of debris, combustible materials, or chemicals. Exercise particular care when charging in non-commercial environments.

• Follow battery usage, storage, and charging guidelines in the user's guide.
• Improper battery use may result in fire, explosion, or other hazard.
• Battery and charger temperatures must be between +32°F and +104°F (0°C and +40°C) for charging.
• Do not use incompatible batteries and chargers. Contact Zebra support if unsure about compatibility.
• For devices using a USB port for charging, connect only to products bearing the USB-IF logo or that have completed the USB-IF compliance program.
• Do not disassemble, open, crush, bend, deform, puncture, or shred batteries.
• Severe impact from dropping a battery-operated device could cause the battery to overheat.
• Do not short-circuit a battery or allow conductive objects to contact battery terminals.
• Do not modify, remanufacture, insert foreign objects, immerse in water or other liquids, or expose to fire, explosion, or other hazard.
• Do not leave or store equipment in very hot areas, such as a parked vehicle or near heat sources. Do not place batteries in microwave ovens or dryers.
• Supervise children's battery usage.
• Dispose of used rechargeable batteries promptly according to local regulations.
• Do not dispose of batteries in fire.
• Seek medical advice immediately if a battery has been swallowed.
• If a battery leaks, do not allow liquid to contact skin or eyes. Wash affected area with water and seek medical advice.
• If equipment or battery damage is suspected, contact Zebra support for inspection.

Radio Frequency Interference Requirements

FCC

Note: This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15 of FCC rules. These limits provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used per instructions, it may cause harmful interference to radio communications. No guarantee that interference will not occur in a particular installation.

If interference occurs, try to correct it by:

• Reorienting or relocating the receiving antenna.
• Increasing separation between equipment and receiver.
• Connecting equipment to an outlet on a different circuit than the receiver.
• Consulting the dealer or an experienced radio/TV technician.

Radio Transmitters (Part 15)

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Radio Frequency Interference Requirements Canada

CAN ICES-3 (B)/NMB-3(B)

Radio Transmitters

This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation.

French translation: Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi même si le brouillage est susceptible d'en compromettre le fonctionnement.

For RLAN Devices:

The use of 5 GHz RLAN in Canada has the following restrictions: Restricted Band 5.60 - 5.65 GHz.

French translation: Pour les équipements RLAN: L'utilisation de la bande RLAN 5 GHz au Canada présente les limitations suivantes: Bande restreinte 5.60 - 5.65 GHz.

Label Marking: The term 'IC:' before the radio certification signifies that Industry Canada technical specifications were met.

French translation: Etiquette de marquage: Le terme "IC" avant la certification radio signifie que le produit est compatible avec la spécification Industrie Canada.

Marking and European Economic Area (EEA)

The use of 5 GHz RLAN throughout the EEA has the following restrictions: 5.15 - 5.35 GHz is restricted to indoor use only.

Statement of Compliance

Zebra declares this radio equipment complies with Directives 2014/53/EU and 2011/65/EU. The full text of the EU Declaration of Conformity is available at: www.zebra.com/doc.

Korea Warning Statement for Class B ITE

[Korean text indicating Class B ITE compliance]

Other Countries

Australia

The use of 5 GHz RLAN in Australia is restricted in the band 5.60 - 5.65 GHz.

Brazil

"Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados"

Este produto está homologado pela Anatel, de acordo com os procedimentos regulamentados pela Resolução nº242/2000 e atende aos requisitos técnicos aplicados, incluindo os limites de exposição da Taxa de Absorção Específica referente a campos elétricos, magnéticos e eletromagnéticos de radiofrequência, de acordo com as Resoluções nº 303/2002 e 533/2009.

Chile

Conforme a Resolución 755 parte j.1), el dispositivo se ajustará para operar en interiores en las siguientes bandas con una potencia máxima radiada no superior a 150mW:

• 2.400 a 2.483,5 MHz
• 5.150 a 5.250 MHz
• 5.250 a 5.350 MHz
• 5,470 a 5.725 MHz
• 5.725 a 5.850 MHz

Además, de acuerdo con Resolucin 755, para la banda 5.150 - 5.250 MHz la operación del equipo estará restringida al interior de inmuebles y la densidad de potencia radiada máxima no supera 7,5 mW/MHz en cualquier banda de 1 MHz y 0.1875 mW/25 kHz en cualquier banda de 25 kHz.

Para la tecnología NFC en la banda 13.553 a 13.567 kHz, la intensidad de campo eléctrico no excederá 20 mV/m a 30 metros, conforme a Resolución 755 parte Art 1. e).

China

[Chinese text indicating compliance]

Website: www.zebra.com/support

[CCC Mark]

Eurasian Customs Union

[EAC Mark]

Hong Kong

In accordance with HKTA1039, the band 5.15 GHz - 5.35 GHz is for indoor operation only.

Mexico

La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.

South Korea

[Korean text indicating compliance]

Taiwan

[Taiwanese text indicating compliance]

Ukraine

[Ukrainian text indicating compliance]

Thailand

[Thai text indicating compliance]

Turkish WEEE Statement of Compliance

EEE Yönetmeliine Uygundur.

Waste Electrical and Electronic Equipment (WEEE)

English:

For EU Customers: All products at the end of their life must be returned to Zebra for recycling. For information on how to return product, please go to: www.zebra.com/weee.

End User License Agreement (EULA)

IMPORTANT PLEASE READ CAREFULLY: This End User License Agreement ("EULA") is a legal agreement between you ("Licensee") and Zebra International Holdings Corporation ("Zebra") for software owned by Zebra and its affiliates and third-party suppliers and licensors, which includes machine-readable instructions ("Software"). BY USING THE SOFTWARE, YOU ACKNOWLEDGE ACCEPTANCE OF THE TERMS OF THIS EULA. IF YOU DO NOT ACCEPT THESE TERMS, DO NOT USE THE SOFTWARE.

1. GRANT OF LICENSE.

Zebra grants you, the End User Customer, a limited, personal, non-exclusive license to use the Software solely for your internal use in support of Zebra hardware. You may install one copy on one Electronic Device. You may make one backup copy. In the absence of a support contract, you are entitled to updates and technical support for ninety (90) days from shipment or download ("Entitlement Period").

Certain Software may be subject to open source licenses, which may override EULA terms. Applicable open source licenses are available via a Legal Notices readme file on your device or in System Reference guides.

1.1 Authorized Users.

For standalone applications, licenses are limited to the number of authorized users. Additional licenses can be purchased.

1.2 Software Transfer.

You may transfer this EULA and software rights to a third party only in connection with the support or sale of a device or standalone application during the Entitlement Period or under a Zebra support contract. The transfer must include all software components and documentation, and you may not retain copies. Prior to transfer, the recipient must agree to EULA terms.

2. RESERVATION OF RIGHTS AND OWNERSHIP.

Zebra reserves all rights not expressly granted. The Software is protected by intellectual property laws. Zebra or its suppliers own the title, copyright, and intellectual property rights.

3. LIMITATIONS ON END USER RIGHTS.

You may not reverse engineer, decompile, disassemble, modify, or create derivative works from the Software. You may not rent, lease, lend, sublicense, or provide commercial hosting services with the Software.

4. CONSENT TO USE OF DATA.

Zebra and its affiliates may collect and use technical information gathered for product support that does not personally identify you, solely to improve products or provide customized services. Your information is treated according to Zebra's Privacy Policy: www.zebra.com.

5. LOCATION INFORMATION.

The Software may enable collection of location-based data. Zebra disclaims liability for misuse of this data. You agree to cover Zebra's costs from third-party claims related to your use of location data.

6. SOFTWARE RELEASES.

Zebra or its channel partners may provide software releases. This EULA applies unless other terms are provided. You must be licensed for the Software to receive releases. Periodically check for support contract availability to ensure entitlement to releases.

7. EXPORT RESTRICTIONS.

You acknowledge the Software is subject to export restrictions and agree to comply with all applicable international and national laws, including export laws and regulations.

8. ASSIGNMENT.

You may not assign this Agreement or your rights/obligations without Zebra's prior written consent. Zebra may assign this Agreement without your consent.

9. TERMINATION.

Your rights terminate automatically if you fail to comply with the EULA. Zebra may terminate by offering a superseding Agreement. Upon termination, cease all use of the Software and destroy all copies.

10. DISCLAIMER OF WARRANTY.

SOFTWARE IS PROVIDED "AS IS" AND "AS AVAILABLE" WITHOUT WARRANTIES. ZEBRA DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT. ZEBRA DOES NOT WARRANT UNINTERRUPTED OR ERROR-FREE OPERATION. EMULATION LIBRARIES ARE PROVIDED "AS IS" WITH ALL FAULTS.

11. THIRD-PARTY APPLICATIONS.

Zebra makes no representations about third-party applications included with the Software. Use of third-party applications is at your sole risk. Zebra is not responsible for any damage or loss caused by or related to third-party content or services. Use of third-party applications is governed by their respective terms.

12. LIMITATION OF LIABILITY.

ZEBRA IS NOT LIABLE FOR DAMAGES ARISING FROM USE OR INABILITY TO USE THE SOFTWARE OR THIRD-PARTY APPLICATIONS, INCLUDING INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF ADVISED OF THE POSSIBILITY. ZEBRA'S TOTAL LIABILITY IS LIMITED TO THE FAIR MARKET VALUE OF THE SOFTWARE OR THE AMOUNT PAID BY THE PURCHASER.

13. INJUNCTIVE RELIEF.

You acknowledge that Zebra is entitled to obtain an injunction against breach of this Agreement without posting bond.

14. MODIFICATION.

No modification of this Agreement is binding unless in writing and signed by an authorized representative.

15. U.S. GOVERNMENT END USERS RESTRICTED RIGHTS.

Software is a "commercial item" with restricted rights granted to U.S. Government end users, consistent with federal regulations.

16. APPLICABLE LAW.

This EULA is governed by the laws of the state of Illinois, excluding its conflict of law provisions and the UN Convention on Contracts for the International Sale of Goods.

CMM Disclosure

This table indicates the presence of restricted substances in compliance with China RoHS requirements.

Note 1: "Exceeding 0.1 wt%" and "exceeding 0.01 wt%" indicate the percentage content of the restricted substance exceeds the reference percentage value.

Note 2: "O" indicates the percentage content of the restricted substance does not exceed the reference value.

Note 3: "-" indicates the restricted substance corresponds to an exemption.