Product description Ԏ The mic sensor with two switching outputs measures the distance to an object within the detection zone contactless. Depending on the ad-justed detect distance the switching
Operating Manual mic+ Ultrasonic Sensors with two switching outputs mic+25/DD/TC mic+35/DD/TC mic+130/DD/TC mic+340/DD/TC mic+600/DD/TC mic+25/EE/TC mic+35/EE/TC mic+130/EE/TC mic+340/EE/TC mic+600/EE/TC Product description The mic+ sensor with two switching outputs measures the distance to an object within the detection zone contactless. Depending on the adjusted detect distance the switching output is set. All settings are done with two pushbuttons and a three-digit LED-display (TouchControl). Three-colour LEDs indicate the switching status. The output functions are changeable from NOC to NCC. The sensors are adjustable manually via TouchControl or via Teach-in procedure. Useful additional functions are set in the Add-on-menu. Using the LinkControl adapter (optional accessory) all TouchControl and additional sensor parameter settings can be adjusted by a Windows® Software. Safety Notes Read the operating instructions prior to start-up. Connection, installation and ad- justment works may only be carried out by expert personnel. No safety component in accordance with the EU Machine Directive, use in the area of personal and machine protection not permitted Proper Use mic+ ultrasonic sensors are used for non-contact detection of objects. The mic+ sensors have a blind zone in which distance measurement is not possible. The operating range indicates the distance of the sensor that Diagram 1: Set sensor parameters numerically using LED display Start here T1 + T2 Press T1 and T2 simultaneously for about 3 s until welcome message has passed. Set switching output D1 Set switching output D2 T1 T2 T1 T2 T1 1 T1 + T2 T1 + T2 T2 Set detect distance in mm or cm. 1 2 For single switching point press T2 T2 until » « is T1 displayed. For window mode T2 operation set far switching point in mm or cm. T1 + T2 Choose » « for NCC or T1 T2 » « for NOC. T1 + T2 T1 T2 T1 + T2 Ready can be applied with normal reflectors with sufficient function reserve. When using good reflectors, such as a calm water surface, the sensor can also be used up to its maximum range. Objects that strongly absorb (e.g. plastic foam) or diffusely reflect sound (e.g. pebble stones) can also reduce the defined operating range. Synchronisation If the assembly distance of multiple sensors falls below the values shown in Fig. 1 the integrated synchronisation should be used. Connect Sync/ Com-channels (pin 5 at the units receptable) of all sensors (10 maximum). mic+25... 0.35m 2.50m mic+35... 0.40m 2.50m mic+130... 1.10m 8.00m mic+340... 2.00m 18.00m mic+600... 4.00m 30.00m Fig. 1: Assembly distances, indicating synchronisation/multiplex Multiplex mode The Add-on-menu allows to assign an individual address »01« to »10« to each sensor connected via the Sync/ Com-channel (Pin5). The sensors perform the ultrasonic measurement sequentially from low to high address. Therefore any influence between the sensors is rejected. The address »00« is reserved to synchronisation mode and deactivates the multiplex mode. To use synchronised mode all sensors must be set to address »00«. Installation Î Assemble the sensor at the installa- tion location. Î Plug in the connector cable to the M12 connector, see Fig. 2. 2 1 35 4 1 3 4 2 5 +UB UB D2 D1 Sync/Com colour brown blue black white grey Fig. 2: Pin assignment with view onto sensor plug and colour coding of the microsonic connection cable Start-up Î Connect the power supply. Î Set the parameters of the sensor manually via TouchControl (see Fig. 3 and Diagram 1) Î or use the Teach-in procedure to adjust the detect points (see Diagram 2). cm mm % Measuring Range 3-digit LED-display LED D1 and D2 T1 D1D2 T2 Push-buttons T1 and T2 Fig. 3: TouchControl/LED display Factory setting mic+ sensors are delivered factory made with the following settings: Switching outputs on NOC Detecting distance at operating ran- ge and half operating range Measurement range set to maxi- mum range Maintenance mic+ sensors work maintenance free. Small amounts of dirt on the surface do not influence function. Thick layers of dirt and caked-on dirt affect sensor function and therefore must be removed. Notes mic+ sensors have internal tempe- rature compensation. Because the sensors heat up on their own, the temperature compensation reaches its optimum working point after approx. 30 minutes of operation. During normal operating mode, a yellow LED signals that the switching output has connected. During normal operating mode, the measured distance value is displayed on the LED-indicator in mm (up to 999mm) or cm (from 100cm). Scale switches automatically and is indicated by a point on top of the digits. During Teach-in mode, the hysteresis loops are set back to factory settings. If no objects are placed within the detection zone the LED-indicator shows » «. If no push-buttons are pressed for 20 seconds during parameter setting mode the made changes are stored and the sensor returns to normal operating mode. The sensor can be reset to its factory setting, see »Key lock and factory setting«, Diagram 3. Show parameters Î In normal operating mode shortly push T1. The LED display shows »PAr.« Each time you tap push-button T1 the actual settings of the analogue output are shown. Diagram 2: Set sensor parameters via Teach-in procedure 1 Set switching point D1/D2 Teach-in switching output D1/D2 1 2 1 85% Set window limits D1/D2 Set two way reflective barrier D1/D2 Set D1/D2 NOC/NCC Place object at position 1 . Place object at position 1 . Place reflector at position 1 . Press T1/T2 until »d1«/»d2« is shown. Press T1/T2 until »d1«/»d2« is shown. Current measuring value Current measuring value Place object at position 2 . Current measuring value Press T1/T2 until »End« is shown. Press T1/T2 until »End« is shown. Press T1/T2 until »d1«/»d2« is shown. Press T1/T2 until countdown passed from »8 « to »0« and NOC or NCC symbol is displayed. Current measuring value NOC symbol Press T1/T2 until countdown passed from »8 « to »0« and »End« is displayed. or NCC symbol To change output characteristic press T1/T2. Normal operating mode Press T1 and T2 simultaneously until »End« is displayed. Diagram 3: Key lock and factory setting Activate/deactivate TouchControl Reset to factory setting Turn supply voltage OFF. Turn supply voltage OFF. While pressing T1 turn supply voltage ON. While pressing T1 turn supply voltage ON. Keep T1 pressed until »on« or »off« is displayed . »on« or »off« / »off« or »on« To activate or deactivate press T1. Keep T1 pressed for about 15 s until »rESEt« has passed through the display. Don´t press any push-button for 20 s. Normal operating mode Diagram 4: Useful additional functions in Add-on menu (for experienced users only, settings not required for standard applications) Start here T1 + T2 Press T1 and T2 simultaneously for about 13 s until »Add« is shown in the LED-display. T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T2 T1 T1 + T2 Ready »C01«: Display bright »C02«: Display dimmed »C03«: Display off Note Changes in the Add-on menu may impair the sensor function. A6, A7, A8, A10, A11, A12 have influence on the response time of the sensor. Low power mode Minimum value: »001« Maximum value: difference between maximum range and switching point - 1 During window mode operation hysteresis influences both switching points. Minimum value: »001« Maximum value: difference between maximum range and switching point - 1 During window mode operation hysteresis influences both switching points. »F00«: no filter »F01«: standard filter »F02«: averaging filter »F03«: foreground filter »F04«: background filter Defines the strength of the chosen filter. »P00«: weak filter up to »P09«: strong filter Delay in seconds between the detection of an object and the output of the measured distance in case of object approach (behaves as on-delay). "00": 0 s (no delay) up to "20": 20 s response time Minimum value: blind zone Maximum value: nearwindow limit - 1 »00«: synchronisation »01« to »10«: sensor address for multiplex mode »oFF«: synchronisation deactivated To optimize multiplex speed the highest sensor address may be set. Setting range »01« to »10« Hysteresis switching Hysteresis switching output D1 output D2 Measurement filter Filter strength Response time Foreground suppression Multiplex mode device addressing Multiplex mode highest address Minimum value: sensor-distant window limit Maximum value: 999 mm for mic+25/..., mic+35/..., 999 cm for mic+130/..., mic+340/..., mic+600/... Put plane reflector vertically disposed in front of sensor: in an exact distance of 250 mm for mic+ 25... and mic+35... and 900 mm for all other types. Adjust display to 250 mm or 900 mm. Confirm calibration with T1+T2. Affects the size of the detection zone. »E01«: high »E02«: standard »E03«: slight Measurement range Calibration display Detection zone sensitivity M12x1 M12x1 M12x1 M12x1 Ø47.5 M12x1 Ø65 Technical data 1 2 U 4 5 3 2 pnp switching outputs +UB D1 D2 Sync/Com UB mic+25... TouchControl LED-Display 36 width A/F 2 Buttons M30x1.5 5 2 Duo-LEDs 1 2 U 4 5 3 2 npn switching outputs +UB E1 E2 Sync/Com UB 51 84 blind zone 0 to 30mm operating range 250mm maximum range 350mm angle of beam spread see detection zone transducer frequency 320kHz resolution 0.025mm detection zones for different objects: The dark grey areas represent the zone where it is easy to recognise the normal reflector (round bar). This indicates the typical operating range of the sensors. The light grey areas represent the zone where a very large reflector for instance a plate can still be recognised. The requirement here is for an optimum alignment to the sensor. It is not possible to evaluate ultrasonic reflections outside this area. 0 cm Plate 5 cm 10 cm Round bar ø 10 mm 15 cm 20 cm 25 cm 30 cm 35 cm 10 cm 5 cm 0 cm 5 cm 10 cm 20 cm 10 cm 0 cm 10 cm 20 cm 0.8 m 0.4 m 0m 0.4 m 0.8 m 1.6 m 0.8 m 0m 0.8 m 1.6 m 2.4 m 1.2 m 0m 1.2 m 2.4 m mic+35... TouchControl LED-Display 36 width A/F 2 Buttons M30x1.5 5 2 Duo-LEDs 0 to 65mm 350mm 600mm see detection zone 400kHz 0.025mm 51 84 0 cm Plate 10 cm 20 cm Round bar ø 10 mm 30 cm 35 cm 40 cm 50 cm 60 cm mic+130... TouchControl LED-Display 36 width A/F 2 Buttons M30x1.5 5 2 Duo-LEDs mic+340... TouchControl LED-Display 36 width A/F 2 Buttons M30x1.5 5 2 Duo-LEDs 0 to 200mm 1,300mm 2,000mm see detection zone 200kHz 0.18mm 51 84 0 to 350mm 3,400mm 5,000mm see detection zone 120kHz 0.18mm 69 102 19.5 33 0 m Plate 0.4 m 0.8 m Round bar ø 10 mm 1.2 m 1.3 m 1.6 m 2 m 0 m Plate 0.8 m 1.6 m Round bar ø 27 mm 2.4 m 3.2 m 3.4 m 4 m 4.8 m 5.6 m mic+600... TouchControl LED-Display 36 width A/F 2 Buttons M30x1.5 5 2 Duo-LEDs 0 to 600mm 6,000mm 8,000mm see detection zone 80kHz 0.18mm 72 105 22.5 36 0 m Plate 1.2 m 2.4 m Round bar ø 27 mm 3.6 m 4.8 m 6 m 7.2 m 8.4 m reproducibility ±0.15 % ±0.15 % ±0.15 % ±0.15 % ±0.15 % accuracy ±1% (Temperature drift internal compensated, may ±1% (Temperature drift internal compensated, may ±1% (Temperature drift internal compensated, may ±1% (Temperature drift internal compensated, may ±1% (Temperature drift internal compensated, may be deactivated 3), 0.17%/K without compensation) be deactivated 3), 0.17%/K without compensation) be deactivated 3), 0.17%/K without compensation) be deactivated 3), 0.17%/K without compensation) be deactivated 3), 0.17%/K without compensation) operating voltage UB 9 to 30V DC, short-circuit-proof, Class 2 9 to 30V DC, short-circuit-proof, Class 2 9 to 30V DC, short-circuit-proof, Class 2 9 to 30V DC, short-circuit-proof, Class 2 9 to 30V DC, short-circuit-proof, Class 2 voltage ripple ±10% ±10% ±10% ±10% ±10% no-load supply current 80mA 80mA 80mA 80mA 80mA housing Brass sleeve, nickel-plated, plastic parts: PBT, TPU; Brass sleeve, nickel-plated, plastic parts: PBT, TPU; Brass sleeve, nickel-plated, plastic parts: PBT, TPU; Brass sleeve, nickel-plated, plastic parts: PBT, TPU; Brass sleeve, nickel-plated, plastic parts: PBT, TPU; Ultrasonic transducer: polyurethane foam, Ultrasonic transducer: polyurethane foam, Ultrasonic transducer: polyurethane foam, Ultrasonic transducer: polyurethane foam, Ultrasonic transducer: polyurethane foam, epoxy resin with glass content epoxy resin with glass content epoxy resin with glass content epoxy resin with glass content epoxy resin with glass content class of protection to EN 60529 IP67 IP67 IP67 IP67 IP67 norm conformity EN 60947-5-2 EN 60947-5-2 EN 60947-5-2 EN 60947-5-2 EN 60947-5-2 type of connection 5-pin initiator plug, PBT 5-pin initiator plug, PBT 5-pin initiator plug, PBT 5-pin initiator plug, PBT 5-pin initiator plug, PBT controls 2 push-buttons (TouchControl) 2 push-buttons (TouchControl) 2 push-buttons (TouchControl) 2 push-buttons (TouchControl) 2 push-buttons (TouchControl) indicators 3-digit LED display, 2 three-colour LEDs 3-digit LED display, 2 three-colour LEDs 3-digit LED display, 2 three-colour LEDs 3-digit LED display, 2 three-colour LEDs 3-digit LED display, 2 three-colour LEDs programmable with TouchControl and LinkControl with TouchControl and LinkControl with TouchControl and LinkControl with TouchControl and LinkControl with TouchControl and LinkControl operating temperature 25 to +70°C 25 to +70°C 25 to +70°C 25 to +70°C 25 to +70°C storage temperature 40 to +85°C 40 to +85°C 40 to +85°C 40 to +85°C 40 to +85°C weight 150g 150g 150g 210g 270g switching hysteresis 1) 3mm 5mm 20mm 50mm 100mm switching frequency 2) 25Hz 12Hz 8Hz 4Hz 3Hz response time 2) 32ms 64ms 92ms 172ms 240ms time delay before availability <300ms <300ms <300ms <380ms <450ms order No. mic+25/DD/TC switching output 2 x pnp, UB 2V, Imax = 2 x 200mA switchable NOC/NCC, short-circuit-proof mic+35/DD/TC 2 x pnp, UB 2V, Imax = 2 x 200mA switchable NOC/NCC, short-circuit-proof mic+130/DD/TC 2 x pnp, UB 2V, Imax = 2 x 200mA switchable NOC/NCC, short-circuit-proof mic+340/DD/TC 2 x pnp, UB 2V, Imax = 2 x 200mA switchable NOC/NCC, short-circuit-proof mic+600/DD/TC 2 x pnp, UB 2V, Imax = 2 x 200mA switchable NOC/NCC, short-circuit-proof order No. mic+25/EE/TC mic+35/EE/TC switching output 2 x npn, UB + 2V, Imax = 2 x 200mA switchable NOC/NCC, short-circuit-proof 2 x npn, UB + 2V, Imax = 2 x 200mA switchable NOC/NCC, short-circuit-proof 1) Can be programmed via TouchControl and LinkControl. 2) With TouchControl and LinkControl, the selected filter setting and the maximum range influence the switching frequency and the response time. 3) Can be deactivated via LinkControl. mic+130/EE/TC 2 x npn, UB + 2V, Imax = 2 x 200mA switchable NOC/NCC, short-circuit-proof mic+340/EE/TC 2 x npn, UB + 2V, Imax = 2 x 200mA switchable NOC/NCC, short-circuit-proof mic+600/EE/TC 2 x npn, UB + 2V, Imax = 2 x 200mA switchable NOC/NCC, short-circuit-proof microsonic GmbH / Phoenixseestraße 7 / 44263 Dortmund / Germany / T +49 231 975151-0 / F +49 231 975151-51 / E info@microsonic.de / W microsonic.de The content of this document is subject to technical changes. Specifications in this document are presented in a descriptive way only. They do not warrant any product features. Enclosure Type 1 The proximity switches shall be used with a For use only in industrial Listed (CYJV/7) cable/connector assembly ramachinery NFPA 79 applications. ted minimum 32 Vdc, minimum 290 mA, in the final installation. Registration no. 75330-19 Approved on June 25th, 2019 *B5396* MV-DO-041943-859287Adobe InDesign 18.5 (Macintosh) Adobe PDF Library 17.0