CYCPLUS Smart Bike Trainer

1.1 Quick Start

Find CYCPLUS on Instagram and Facebook for instruction videos, FAQ, and more support.

• Instagram: cycplus_official
• Facebook: cycplus
• YouTube: CYCPLUS

Official website: www.cycplus.com

After-sales email: steven@cycplus.com

1.2 Notice

• Keep children and pets away from T2 while in use.
• Keep clear of the motor and moving parts while in use.
• The T2 enclosure will heat up during use. Ensure the cooling holes are clear. For high-intensity riding, plug in the power to keep the fan working.
• Please use the T2 on a stable surface with adjusted leveling feet before use.
• Use caution when standing while riding on T2.
• Do not install or disassemble the bicycle until T2 completely stops.
• Do not use other power source to power T2.
• Please confirm whether the bicycle is installed properly before every ride.

1.3 Factory Info

Manufacturer: Chengdu Chendian Intelligent Technology Co., Ltd

Warranty: Free replacement or repair within 1 year.

After sale email: steven@cycplus.com

1.4 Packing List

T2 Unit

Accessories:

• 02 Cassette pre-installed
• 03 Thru-axle adapter-R (pre-installed)
• 04 Thru-axle adapter-L (pre-installed)
• 05 Quick release adapter-R
• 06 Quick release adapter-L
• 07 17mm Wrench (for thru-axle adapter-R)
• 08 Allen key (for quick release adapter-R)
• 09 8-10 speed cassette spacer
• 10 Cassette adjustment spacer [7x] (Including 2 pcs pre-installed)
• 11 Disc brake spacer
• 12 Hydraulic Disk Brake Pad Spacer
• 13 Quick release
• 14 AC adapter
• 15 AC cable
• 16 Cushioning mat
• 17 USB ANT+ receiver and Extension Cable

2.1 Ground and stabilize T2

1. Press and hold the lock catch.
2. Unfold the leg. Align the lock catch with the notch, and make sure the latch pops up and locks the angle of the leg. [Press to unlock] / [Release to lock]
3. Unfold all the legs in turn.
4. Adjust the leveling feet to balance and stabilize T2.
   Adjust the height of the foot: Rotate clockwise to raise, rotate counterclockwise to lower.
   Lock the height of the foot: Rotate counterclockwise to secure.

2.2 Cassette Mounting

T2 comes preinstalled with a cassette. Read instructions below if you need to mount another one.

1. For 8/9/10 speed cassettes, put on the spacer before installing the cassette. [Cassette spacer with notch outward]
2. For SRAM 12 speed cassettes, an XDR hub will be needed to buy additionally. [Tip: Use cassette removal tools to secure the cassette after pushing it into the hub.]

2.3 Precautions and Disclaimer

1. Identify the frame type and standard (thru-axle or quick release) before proceeding with installation.
   For thru-axle, refer to "2.4 For Bikes with Rear Thru-Axles" for installation.
   For quick release, refer to "2.5 For Bikes with Quick Release Skewers" for installation.
   Carefully go through the manual and compare it with the actual parts to make sure all of them are complete and properly installed before mounting your bike to T2.
2. For hydraulic disc brakes, install the pad spacer between the brake pads (as shown on the right) after removing the rear wheel, to prevent you from accidentally closing the brake without the rotor in place. Please use your own pad spacer if the spacer coming with T2 is not compatible with your disc brake. [Use this notch to clip the spacer to the retaining pin]
3. T2 is compatible with most quick release and thru axle frames including those with disc brake sets. However, there are still a few special frames, because of the shape of the rear fork and the location of the disc brake set, may not be compatible with T2.
   For bikes with disc brake sets and a chain stay shaped as shown below, they are very likely to be incompatible with T2, and do not force to install. [Special-shaped chain stay] [Possible area in contact]
   For bikes with disc brake sets, make sure the disc brake set is not against the housing of T2. If you find any contact or friction, do not force to install.
4. Read the manual thoroughly and be sure to follow the instructions provided in the manuals when using T2. Don't hesitate to contact CYCPLUS for support and don't force to install.
   CYCPLUS is not responsible for damage or loss caused by incorrect installation, incompatible bike frame or customer's forcing installation.

2.4 For Bikes with Rear Thru-Axles

1. Install the Thru-axle adapter-R(03) with 17mm wrench(07). T2 comes preinstalled with thru-axle adapter and 2 spacers.
2. Install the Thru-axle adapter-L(04). [Outwards for Mountain bike 148] [Outwards for Road bike 142]
3. Adjust the shifter until the chain is on the smallest sprockets of both chainwheel and cassette.
4. Align the bicycle chain with the minimum sprocket of the cassette and install the frame onto the bike trainer.
5. Secure the bike with the thru-axle of your bike. [Original thru-axle]
6. Shake the bike frame after installation to make sure the frame is secured to T2.

WARNING!

• Failure to properly secure the bike can result in serious property damage and personal injury.
• Never adjust the quick release skewer or thru axle while someone is sitting on the bike.
• There are still a few bike frames incompatible with T2. Stop the installation immediately if any abnormalities occur.
• Please refer to the disclaimer and don't hesitate to contact CYCPLUS for any installation problems.

2.5 For Bikes with Quick Release Skewers

1. Install the Quick release adapter-R(05) with the Allen key(08). T2 comes preinstalled with quick release adapter. Remove it before installation, and confirm 2 spacers are installed.
2. Install the Quick release adapter-L(06). [Outwards for Mountain bike & Road bike with disk-brake 135] [Outwards for Road bike with rim brake 130]
3. Insert the quick release skewer into the axle of T2 and install the nut in place, but don't tighten it yet, in order to install the bike frame.
4. Adjust the shifter until the chain is on the smallest sprockets of both chainwheel and cassette.
5. Align the bike chain with the smallest sprocket of the cassette on T2, and mount the frame to T2.
6. Adjust the lock nut of the quick release skewer, and lift and press the handle frequently at the same time until the pressing resistance is appropriate, then press the handle to secure the skewer.
7. Shake the bike frame after installation to make sure the frame is secured to T2.

WARNING!

• Failure to properly secure the bike can result in serious property damage and personal injury.
• Never adjust the quick release skewer or thru axle while someone is sitting on the bike.
• There are still a few bike frames incompatible with T2. Stop the installation immediately if any abnormalities occur.
• Please refer to the disclaimer and don't hesitate to contact CYCPLUS for any installation problems.

2.6 Power Connection

Please use the AC adapter only that comes with T2 to power the device. The AC cable can be replaced according to your needs.

[Diagram of AC adapter and cable connected to T2]

3 Working Status

1. Working modes

T2 has 2 working modes, unplugged mode and plug-in mode. Plug-in mode can provide a better riding experience. The main functional differences between the two modes are as follows:

Notice: It is recommended for high-intensity riders to ride in plug-in mode for electricity to dissipate heat for T2 after stop.

2. Indicators

• [Power symbol] [Bluetooth symbol] [ANT symbol]
• Solid light: ANT data broadcast working properly
• Solid light: bluetooth connected
• Flashing: bluetooth not connected
• Solid light: Power supply works properly

4 Application

1. Please download "CYCPLUS" App in App Store or Google Play. [CYCPLUS APP icon] [App Store icon] [Google Play icon]
2. T2 is a true direct-drive trainer and requires no calibration.
3. T2 supports both Bluetooth and ANT+ wireless connection protocols when using indoor cycling Apps. We recommend using Bluetooth connection in preference, for more stable signal. For ANT+ connection, place the ANT receiver as close as possible to the indicator spot on of T2. [Diagram showing ANT receiver placement]

5 Spacers (for possible noise and friction)

5.1 Cassette adjustment spacer (for loud chain noise)

If the chain noise becomes too loud while training, it may be because the distance between the T2 cassette and the rear fork (A) and the distance between your original cassette and the rear fork (B) are different, and the bike chain and cassette do not fit well. For your convenience in adjusting the distance, there are 2 spacers pre-installed between the cassette and the Thru-axle adapter-R or Quick release adapter-R.

1. A<B Try adding more cassette adjustment spacers to T2. Each piece is about 0.4mm thick.
2. A>B Try removing some spacers to reduce the distance. If there are still issues after removing all the spacers, please contact CYCPLUS for help.

[Diagram illustrating spacer adjustment]

5.2 Disc brake spacer (for friction)

If friction occurs between the disc brake on your bike and the T2 housing, you can use disc brake spacers to increase the distance to avoid friction while training. *This mostly happens with SRAM spec 140mm disc brakes.

[Diagram illustrating disc brake spacer usage]

Visit our youtube channel (CYCPLUS) for more detailed official videos, or contact our customer service for more information.

5 Specifications