User Manual for iskydance models including: V1-L Single Color LED Controller, Single Color LED Controller, LED Controller
Match Remote Control (two match ways). End user can choose the suitable match/delete ways. Two options are offered for selection: Use the controller’s Match key. Use Power.. View
Index of /wp-content/uploads/2022/04/
Single Color LED Controller Model No.: V1-L 1 Channel/Step-less dimming/Wireless remote control/Push Dim/Multiple protection Features LVD RED 4096 levels 0-100% dimming smoothly without any ash. Match with RF 2.4G single zone or multiple zone dimming remote control. One RF controller accept up to 10 remote control. Auto-transmitting function: Controller automatically transmit signal to another controller with 30m control distance. Synchronize on multiple number of controllers. Connect with external push switch to achieve on/off and 0-100% dimming function. Light on/off fade time 3s selectable. Over-heat / Over-load / Short circuit protection, recover automatically. Technical Parameters Input and Output Input voltage Output voltage Output current Output power Output type 12-48VDC 12-48VDC 15A@12/24V 10A@36/48V 180W@12V 360W@24V 360W@36V 480W@48V Constant voltage Environment Operation temperature Case temperature (Max.) IP rating Ta: -30 OC ~ +55 OC T c: +85OC IP20 Warranty and Protection Warranty 5 years Protection Reverse polarity Over-heat Over-load Short circuit User Manual Ver 1.1.1 Dimming data Input signal Control distance Dimming gray scale Dimming range Dimming curve PWM Frequency RF 2.4GHz + Push Dim 30m(Barrier-free space) 4096 (2^12) levels 0 -100% Logarithmic 500Hz (default) Safety and EMC EMC standard (EMC) Safety standard(LVD) Radio Equipment(RED) Certification ETSI EN 301 489-1 V2.2.3 ETSI EN 301 489-17 V3.2.4 EN 62368-1:2020+A11:2020 ETSI EN 300 328 V2.2.2 CE,EMC,LVD,RED Weight Net weight Gross weight 0.099kg 0.116kg Mechanical Structures and Installations Push switch common Push switch + Match key LED indicator 45mm 175mm 160mm - MATCH - IN PUT 12-24VDC - + + 27mm V1-L Single Color LED Controller LED output LED output + Installation rack Power input + Power input - Wiring Diagram Match with dimming remote + V1-L + + Single color LED strip + IN PUT 12-24VDC - - MATCH - AC100-240V Power Supply 12-48VDC Constant Voltage Connect with push switch Push Switch + V1-L + + RF remote Single color LED strip + IN PUT 12-24VDC - - MATCH - AC100-240V Power Supply 12-48VDC Constant Voltage Page 1 Match Remote Control (two match ways) End user can choose the suitable match/delete ways. Two options are offered for selection: Use the controller's Match key Match: Short press match key, immediately press on/off key (single zone remote) or zone key (multiple zone remote) on the remote. The LED indicator fast flash a few times means match is successful. Delete: Press and hold match key for 5s to delete all match, The LED indicator fast flash a few times means all matched remotes were deleted. Use Power Restart Match: Switch off the power, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 3 times on the remote. The light blinks 3 times means match is successful. .Delete: Switch off the power, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 5 times on the remote. The light blinks 5 times means all matched remotes were deleted. Application notes 1. All the receivers in the same zone. 30m 30m 30m RF remote Auto-transmitting: One receiver can transmit the signals from the remote to another receiver within 30m, as long as there is a receiver within 30m, the remote control distance can be extended. Auto-synchronization: Multiple receivers within 30m distance can work synchronously when they are controlled by the same remote. Receiver placement may offer up to 30m communication distance. Metals and other metal materials will reduce the range. Strong signal sources such as WiFi routers and microwave ovens will affect the range. We recommend for indoor applications that receiver placements should be no further apart than15m. 2. Each receiver(one or more) in a different zone, like zone 1, 2, 3 or 4. Zone 1 Zone 2 30m 30m Zone 3 Zone 4 RF remote User Manual Ver 1.1.1 V1-L Single Color LED Controller Push Dim Function The provided Push-Dim interface allows for a simple dimming method using commercially available non-latching (momentary) wall switchs. Short press: Turn on or off light. Long press (1-6s): Press and hold to step-less dimming, With every other long press, the light level goes to the opposite direction. Dimming memory: Light returns to the previous dimming level when switched off and on again, even at power failure. Synchronization: If more than one controller are connected to the same push switch, do a long press for more than 10s, then the system is synchronized and all lights in the group dim up to 100%. This means there is no need for any additional synchrony wire in larger installations. We recommend the number of controllers connected to a push switch does not exceed 25 pieces, The maximum length of the wires from push to controller should be no more than 20 meters. PWM duty(%) Dimming curve Logarithmic dimming curve 100 Gamma=1.6 90 80 70 60 50 40 30 20 10 10 20 30 40 50 60 70 80 90 100 Brightness(%) Light on/off fade time Long press match key 5s, then short press match key 3 times, the light on/off time will be set to 3s, the indicator light blink 3 times. Long press match key 10s, restore factory default parameter, the light on/off time also restore to 0.5s. Malfunctions Analysis & Troubleshooting Malfunctions No light Uneven intensity between front and rear,with voltage drop No response from the remote Causes 1. No power. 2. Wrong connection or insecure. 1. Output cable is too long. 2. Wire diameter is too small. 3. Overload beyond power supply capability. 4. Overload beyond controller capability. 1. The battery has no power. 2. Beyond controllable distance. 3. The controller did not match the remote. Troubleshooting 1. Check the power. 2. Check the connection. 1. Reduce cable or loop supply. 2. Change wider wire. 3. Replace higher power supply. 4. Add power repeater. 1. Replace battery. 2. Reduce remote distance. 3. Re-match the remote. Page 2Corel PDF Engine Version 16.1.0.843 CorelDRAW X6