Buderus SSB Boilers | Modular Condensing Boilers | Products | Commercial
Bosch Buderus Engineering SSB1000TL/TL2/TL3/TL4 Submittal Stainless Steel Condensing Boiler Sheet Boiler Components ® C US Engineering Specifications There shall be provided and installed Bosch Buderus _____ Model SSB1000TL in quantities of ____. Bosch Buderus Stainless Steel Boilers referred to as SSB are condensing hot water boilers, suitable for direct venting. The SSB is factory set for operation using Natural Gas but shall be field convertible to LP Gas using the supplied conversion kit. The SSB SA series Boiler(s) shall utilize two individual plasma welded 316L dual tube stainless steel heat exchanger modules. Both Modules contain independent fan motor, gas valve, burner tube, circulator and all the necessary safety components to allow for true on-board redundancy. Each module is provided with isolation valves and drain to allow for independent service. Boiler(s) shall be constructed, tested and labeled in accordance with ASME Section IV and shall bear the ASME stamp. Boilers shall be CSA approved for USA and Canada and have an applicable Canadian registration Number. Heat exchanger modules shall be labeled for 80 psig (MAWP) maximum allowable working pressure rating. An integrated pressure sensor shall ensure minimum water pressures are maintained. In addition to the minimum water pressure sensor, each module shall encompass a low water cut-out (LWCO) and an individual flow-sensor on each module to identify low water or low flow conditions. Boiler(s) shall be capable of up to 40:1 turndown ratio based upon supply and return water temperatures and/or outdoor reset control. Boiler(s) shall have a settable Power Mode parameter to allow for selection of desired module operation for either parallel or serial operation of up to 8 modules. Boiler(s) shall be designed for large residential, commercial and light industrial applications. Boiler(s) shall be equipped with a 75 lb. pressure relief valve per boiler module. 1 of 10 Bosch Thermotechnology Corp. reserves the right to make changes without notice due to continuing engineering and technological advances | BTC 438008104 E | 10.2020 Bosch Thermotechnology Corp. Watertown, MA · Londonderry, NH · Ft. Lauderdale, FL Tel: 1-866-642-3198 Fax: 1-603-965-7581 www.bosch-thermotechnology.us Bosch Buderus SSB1000TL/TL2/TL3/TL4 Stainless Steel Condensing Boiler Engineering Submittal Sheet Engineering Specifications Boiler(s) shall be equipped with Manual Reset High Limits (MRHL), Low water cut-outs with test button, and Flow Sensors on each boiler module. Boiler(s) shall be equipped with Low and High gas pressure switches with manual resets per ASME CSD-1 requirements. Boiler(s) shall utilize multiple (twin-pipe) or single (concentric or single-pipe) terminations for both vertical and horizontal vent configurations as outlined in the boiler installation manual. Boiler(s) shall be installed in a system that meets the water quality standards outlined in the boiler installation manual. Boiler(s) shall function directly with hydronic emitters. Boiler(s) may be controlled using an enable/disable command from "dry" closure contacts such as a relay or BMS system. Boiler(s) shall be equipped with an optional outdoor air temperature sensor to control supply water temperature based upon outdoor air temperatures for increased fuel efficiency. Boiler(s) shall contain an on-board, 7" color touch-screen which allows for multiple heating configurations including set point operation, outdoor reset using a demand signal, full outdoor reset with constant circulation, permanent heat demand, analog 0-10 Vdc (4 20 mA) setpoint control. The Boiler(s) control shall have multiple domestic hot water heating parameters designed for the most common application including boiler control of an indirect tank thru a manufacturer supplied 10k ohm NTC thermistor or a field supplied aquastat. The Boiler(s) hydraulic manifold piping (water, gas and exhaust/ air) shall be factory installed and self-contained within the Boiler(s) outer cabinet. All external Boiler(s) hydraulic connections shall be able to be connected in any configuration on either the left or right side of the Boiler(s) in order to allow for maximum installation flexibility and site requirements. The Boiler(s) shall be capable of installation in combinations of 2, 3 or 4 TL modules with respective turn-down ratios of 20, 30 and 40 to 1. Multiple Boiler sections shall be engineered so that up to 4 Boilers may be interconnected using the manufacturers provided flanged connections. All manifold piping (water, gas and exhaust/ air) between Boiler sections shall be engineered and sized by the manufacturer to accommodate the hydraulic requirements of up to a maximum of 4 Boilers. Boiler(s) shall be equipped with a multi-speed circulator pump on each module. General Data Boiler category Type of Gas Heat exchanger construction Surface heat exchanger (total) Gas Connections Water Connections Vent/Air Intake Connections Vent Materials Water Volume Weight - dry Shipping Weight Min. clearance to combustibles ** Dimension LxWxH Unit Sq. Ft (m2) Ø Inch Ø Inch Ø Inch (Ø mm) Gallons (Liters) Lbs (kg) Lbs (kg) SSB1000TL ASME Sect.IV Natural Gas, Propane 316L Stainless Steel 86 (8.0) 3" Flanged 5 10 (254) PP, CPVC, Stainless Steel AL29-4C 20.0 (75) 849 (385) 941 (427) SSB1000TL2 ASME Sect.IV Natural Gas, Propane 316L Stainless Steel 172 (16.0) 3" Flanged 5 10 (254) PP, CPVC, Stainless Steel AL29-4C 40.0 (150) 1698 (770) 1882 (854) SSB1000TL3 ASME Sect.IV Natural Gas, Propane 316L Stainless Steel 258 (24.0) 3" Flanged 5 10 (254) PP, CPVC, Stainless Steel AL29-4C 60.0 (225) 2547 (1155) 2823 (1281) SSB1000TL4 ASME Sect.IV Natural Gas, Propane 316L Stainless Steel 344 (32.0) 3" Flanged 5 10 (254) PP, CPVC, Stainless Steel AL29-4C 80.0 (300) 3396 (1540) 3764 (1708) Inch (mm) 2 (51) 2 (51) 2 (51) 2 (51) Inch (mm) 31.5 x 35.4 x 70.9 (800x900x1800) 31.5 x 71.9 x 70.9 (800x1825x1800) 31.5 x 108.3 x 70.9 (800x2750x1800) 31.5 x 144.7 x 70.9 (800x3675x1800) ** The 2" minimum clearance is required for all sides of the boiler. The boiler may be installed on combustible (wood) floors excluding carpets. 2 of 10 Bosch Thermotechnology Corp. Watertown, MA · Londonderry, NH · Ft. Lauderdale, FL Bosch Thermotechnology Corp. reserves the right to make changes without notice due to continuing engineering and technological advances | BTC 438008104 E | 10.2020 Tel: 1-866-642-3198 Fax: 1-603-965-7581 www.bosch-thermotechnology.us Bosch Buderus SSB1000TL/TL2/TL3/TL4 Stainless Steel Condensing Boiler Engineering Submittal Sheet Performance Data Max Input* Min Input Turndown Combustion Eff.* Thermal Eff.* Gross Output* Net Rating* * = AHRI certified performance data Unit BTU/hr (kW) BTU/hr (kW) Ratio (%) Efficiency (%) Efficiency (%) BTU/hr (kW) BTU/hr (kW) SSB1000TL 1,024,000 (300) 100,000 (29) 10:1 (10%) 95.4 96.8 991,000 (290) 861,700 (252) SSB1000TL2 2,048,000 (600) 100,000 (29) 20:1 (10%) 95.4 96.8 1,982,000 (580) 1,723,400 (504) SSB1000TL3 3,072,000 (900) 100,000 (29) 30:1 (10%) 95.4 96.8 2,973,000 (870) 2,585,100 (756) SSB1000TL4 4,096,000 (1200) 100,000 (29) 40:1 (10%) 95.4 96.8 3,964,000 (1160) 3,446,800 (1008) Operational Data Max. NG Pressure Min. NG Pressure Max. LPG Pressure Min. LPG Pressure CO2 Working Range NG (LP) Max. Allowable Working Pressure (MAWP) Max. water flow at max. power (T 27 °F / 15 °C) Recommended water flow @ max power (T 36 °F / 20 °C) Max. operating temperature Max HE allowable temperature Ambient storage temperature dry Ambient functioning temperature Electrical Req. 120VAC/1PH/60Hz Unit Inch W.C. (mbar) Inch W.C. (mbar) Inch W.C. (mbar) Inch W.C. (mbar) % PSI (bar) GPM (m3/h) GPM (m3/h) °F (°C) °F (°C) °F (°C) °F (°C) SSB1000TL 20 (50) 3.5 (8.72) 20 (50) 8 (19.9) 8.5 - 9.5 (10.3 - 10.7) 80 (5.5) 75.8 (17.2) 56.8 (12.9) 194 (90) 210 (98.9) 5 to 158 (-15 to 70) 32 to 120 (0 to 49) 15.1 FLA * SSB1000TL2 SSB1000TL3 SSB1000TL4 20 (50) 20 (50) 20 (50) 3.5 (8.72) 3.5 (8.72) 3.5 (8.72) 20 (50) 20 (50) 20 (50) 8 (19.9) 8 (19.9) 8 (19.9) 8.5 - 9.5 (10.3 - 10.7) 8.5 - 9.5 (10.3 - 10.7) 8.5 - 9.5 (10.3 - 10.7) 80 (5.5) 80 (5.5) 80 (5.5) 151.6 (34.4) 227.4 (51.6) 303.2 (68.8) 113.6 (25.8) 194 (90) 210 (98.9) 5 to 158 (-15 to 70) 32 to 120 (0 to 49) 30.2 FLA * 170.4 (38.7) 194 (90) 210 (98.9) 5 to 158 (-15 to 70) 32 to 120 (0 to 49) 45.3 FLA * 227.2 (51.6) 194 (90) 210 (98.9) 5 to 158 (-15 to 70) 32 to 120 (0 to 49) 60.4 FLA * * FLA (Full Load Amperage) - maximum current drawn by the boiler if all pumps reach rated horsepower. Approval Data Approval description Standard listings & approvals Massachusetts Plumbing Board CRN # SCAQMD approval SSB1000TL SSB1000TL2 SSB1000TL3 CSA, ASME, AHRI Approved Y9641.2C Approved SSB1000TL4 3 of 10 Bosch Thermotechnology Corp. reserves the right to make changes without notice due to continuing engineering and technological advances | BTC 438008104 E | 10.2020 Bosch Thermotechnology Corp. Watertown, MA · Londonderry, NH · Ft. Lauderdale, FL Tel: 1-866-642-3198 Fax: 1-603-965-7581 www.bosch-thermotechnology.us Bosch Buderus SSB1000TL/TL2/TL3/TL4 Stainless Steel Condensing Boiler SSB1000TL Boiler Dimensions 31.49 (800) ø3.00 (76) ø9.84 (250) 35.43 (900) Engineering Submittal Sheet 8.54 (217) 9.88 (251) 7.87 (200) 13.94 (354) 8.74 (222) 70.86 (1800) 52.00 (1321) 17.52 (445) 8.66 (220) 8.29 (211) 11.18 (284) 3.93 (100) ø5.00 (127) ø5.00 (127) 5.31 (135) 11.81 (300) 7.48 (190) Dimensions in inches (mm) Tolerances on all dimensions shown is +/- 1/4" (6.35mm) 4 of 10 Bosch Thermotechnology Corp. reserves the right to make changes without notice due to continuing engineering and technological advances | BTC 438008104 E | 10.2020 Bosch Thermotechnology Corp. Watertown, MA · Londonderry, NH · Ft. Lauderdale, FL Tel: 1-866-642-3198 Fax: 1-603-965-7581 www.bosch-thermotechnology.us Bosch Buderus SSB1000TL/TL2/TL3/TL4 Stainless Steel Condensing Boiler SSB1000TL2 Boiler Dimensions 3 1 . 4 9 (800) 3.00 9.84 (76) (250) 7 1 . 8 5 (1825) 3 5 . 4 3 (900) 3 5 . 4 3 (900) 0 . 9 8 (25) Engineering Submittal Sheet 8 . 5 4 (217) 9 . 8 8 (251) 7.87 (200) 13.94 8.74 (354) (222) 7 0 . 8 6 (1800) 5 2 (1321) 8.29 (211) 11.18 (284) 1 7 . 5 2 (455) 8.66 (220) 3.93 (100) 5 (127) 5 (127) Dimensions in inches (mm) Tolerances on all dimensions shown is +/- 1/4" (6.35mm) 5.31 (135) 1 1 . 8 1 (300) 7 . 4 8 (190) 5 of 10 Bosch Thermotechnology Corp. reserves the right to make changes without notice due to continuing engineering and technological advances | BTC 438008104 E | 10.2020 Bosch Thermotechnology Corp. Watertown, MA · Londonderry, NH · Ft. Lauderdale, FL Tel: 1-866-642-3198 Fax: 1-603-965-7581 www.bosch-thermotechnology.us Bosch Buderus SSB1000TL/TL2/TL3/TL4 Stainless Steel Condensing Boiler Engineering Submittal Sheet SSB1000TL3 Boiler Dimensions 3 5 . 4 3 (900) 1 0 8 . 2 6 (2750) 3 5 . 4 3 (900) 0 . 9 8 (25) 3 5 . 4 3 (900) 0 . 9 8 (25) 3 1 . 4 9 (800) 3.00 9.84 (76) (250) Front 8 . 5 4 (217) 9 . 8 8 (251) 7.87 (200) 13.94 8.74 (354) (222) 7 0 . 8 6 (1800) 5 2 (1321) 8.29 (211) 11.18 (284) 1 7 . 5 2 (455) 8.66 (220) 3.93 (100) 5 (127) 5 (127) Left Side Dimensions in inches (mm) Tolerances on all dimensions shown is +/- 1/4" (6.35mm) 6 of 10 Bosch Thermotechnology Corp. reserves the right to make changes without notice due to continuing engineering and technological advances | BTC 438008104 E | 10.2020 5.31 (135) 1 1 . 8 1 (300) 7 . 4 8 (190) Right Side Bosch Thermotechnology Corp. Watertown, MA · Londonderry, NH · Ft. Lauderdale, FL Tel: 1-866-642-3198 Fax: 1-603-965-7581 www.bosch-thermotechnology.us Bosch Buderus SSB1000TL/TL2/TL3/TL4 Stainless Steel Condensing Boiler Engineering Submittal Sheet SSB1000TL4 Boiler Dimensions 3 5 . 4 3 (900) 1 4 4 . 6 8 (3675) 3 5 . 4 3 (900) 0 . 9 8 (25) 3 5 . 4 3 (900) 0 . 9 8 (25) 3 5 . 4 3 (900) 0 . 9 8 (25) 3 1 . 4 9 (800) 3.00 9.84 (76) (250) Front 8 . 5 4 (217) 9 . 8 8 (251) 7.87 (200) 13.94 8.74 (354) (222) 7 0 . 8 6 (1800) 5 2 (1321) 8.29 (211) 11.18 (284) 1 7 . 5 2 (455) 8.66 (220) 3.93 (100) 5 (127) 5 (127) Left Side Dimensions in inches (mm) Tolerances on all dimensions shown is +/- 1/4" (6.35mm) 7 of 10 Bosch Thermotechnology Corp. reserves the right to make changes without notice due to continuing engineering and technological advances | BTC 438008104 E | 10.2020 5.31 (135) 1 1 . 8 1 (300) 7 . 4 8 (190) Right Side Bosch Thermotechnology Corp. Watertown, MA · Londonderry, NH · Ft. Lauderdale, FL Tel: 1-866-642-3198 Fax: 1-603-965-7581 www.bosch-thermotechnology.us Bosch Buderus SSB1000TL/TL2/TL3/TL4 Stainless Steel Condensing Boiler SSB1000TL Boiler Connections Engineering Submittal Sheet A B C E F G D Boiler Connections Data Item A B C D E F G Description Gas Inlet Flue Exhaust (Flanged) Air Intake System Supply (Flanged) System Return (Flanged) Condensate Outlet Relief Valve Outlet Unit Inch (mm) Inch (mm) Inch (mm) Inch (mm) Inch (mm) Inch (mm) Inch (mm) SSB1000TL 3" Flanged 10 (254) 10 (254) 5 (127) 5 (127) 1-1/2 (50) 2 (60) 8 of 10 Bosch Thermotechnology Corp. reserves the right to make changes without notice due to continuing engineering and technological advances | BTC 438008104 E | 10.2020 Bosch Thermotechnology Corp. Watertown, MA · Londonderry, NH · Ft. Lauderdale, FL Tel: 1-866-642-3198 Fax: 1-603-965-7581 www.bosch-thermotechnology.us Bosch Buderus SSB1000TL/TL2/TL3/TL4 Stainless Steel Condensing Boiler Engineering Submittal Sheet Thermal Efficiency Curves SSB1000TL Thermal Efficiency 100% 98% 96% 94% 92% 90% 100% input 30% input 20% input 88% 80% 70 (21) 80 (27) 90 (32) 100 (38) 110 (43) 120 (49) 130 (54) 140 (60) 150 (66) 160 (38) 170 (77) Return water temperature °F (°C) @ 36 Degree Rise SSB1000TL Water Pressure Drop 9 of 10 Bosch Thermotechnology Corp. reserves the right to make changes without notice due to continuing engineering and technological advances | BTC 438008104 E | 10.2020 Bosch Thermotechnology Corp. Watertown, MA · Londonderry, NH · Ft. Lauderdale, FL Tel: 1-866-642-3198 Fax: 1-603-965-7581 www.bosch-thermotechnology.us Bosch Buderus SSB1000TL/TL2/TL3/TL4 Stainless Steel Condensing Boiler Engineering Submittal Sheet Recommended Boiler Clearances RECOMMENDED SERVICE CLEARANCES . REQUIRED CLEARANCE FROM COMBUSTIBLES . . . Front * * Front * Excluding side with connections. DISCLAIMER Specifications subject to change without notice. All dimensions shown on these engineering submittal sheets are for reference only and should not be used for field installation purposes. Please refer to current product installation manuals for detailed installation instructions and dimensions. 10 of 10 Bosch Thermotechnology Corp. reserves the right to make changes without notice due to continuing engineering and technological advances | BTC 438008104 E | 10.2020 Bosch Thermotechnology Corp. Watertown, MA · Londonderry, NH · Ft. Lauderdale, FL Tel: 1-866-642-3198 Fax: 1-603-965-7581 www.bosch-thermotechnology.usAcrobat Distiller 20.0 (Windows)