Shenzhen Gotron Electronic CO.,LTD. 5021RH Smart Phone 2AOWK-5021RH 2AOWK5021RH 5021rh
Page 1 of 21 Report No.: AiTSZ-250306009FW7 TEST REPORT Product Name : Smart Phone Brand Name : ulefone Model Series Model FCC ID : GQ5021RH : Armor X32, Armor X32 Ultra, Armor X32E, Armor X32S, Armor X32 Lite, Armor X32s, Armor X32s Pro : 2AOWK-5021RH Applicant Address Manufacturer Address Standard(s) : Shenzhen Gotron Electronic CO.,LTD. : 7B01, Building A, Block 1, Anhongji Tianyao Plaza, Longhua District, Shenzhen City, Guangdong Province China : Shenzhen Gotron Electronic CO.,LTD. : 7B01, Building A, Block 1, Anhongji Tianyao Plaza, Longhua District, Shenzhen City, Guangdong Province China : FCC CFR Title 47 Part 15 Subpart C Section 15.225 Date of Receipt : Mar. 06, 2025 Date of Test : Mar. 07, 2025~ Mar. 24, 2025 Issued Date : Mar. 25, 2025 Issued By: Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China Tel.: +86 0755-230967639 Fax.: +86 0755-230967639 Reviewed by: Leon.yi Approved by: Sean She Note: This device has been tested and found to comply with the standard(s) listed, this test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. This report shall not be reproduced except in full, without the written approval of Guangdong Asia Hongke Test Technology Limited. If there is a need to alter or revise this document, the right belongs to Guangdong Asia Hongke Test Technology Limited, and it should give a prior written notice of the revision document. This test report must not be used by the client to claim product endorsement. Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Report Version M1 Page 2 of 21 Report No.: AiTSZ-250306009FW7 Report Revise Record Issued Date Mar. 25, 2025 Notes Initial Release Page 3 of 21 Report No.: AiTSZ-250306009FW7 Contents 1 TEST SUMMARY......................................................................................................................................................4 1.1 TEST STANDARDS .........................................................................................................................................................4 1.2 TEST SUMMARY...........................................................................................................................................................4 1.3 TEST FACILITY..............................................................................................................................................................5 1.4 MEASUREMENT UNCERTAINTY ........................................................................................................................................5 2 GENGENERAL INFORMATION..................................................................................................................................6 2.1 ENVIRONMENTAL CONDITIONS........................................................................................................................................6 2.2 GENERAL DESCRIPTION OF EUT ......................................................................................................................................6 2.3 SPECIAL ACCESSORIES ...................................................................................................................................................7 2.4 EQUIPMENT LIST FOR THE TEST.......................................................................................................................................7 3 TEST CONDITIONS AND RESULTS.............................................................................................................................9 3.1 CONDUCTED EMISSIONS TEST.........................................................................................................................................9 3.2 RADIATED EMISSIONS .................................................................................................................................................12 3.3 20DB BANDWIDTH ....................................................................................................................................................17 3.4 FREQUENCY STABILITY.................................................................................................................................................18 4 TEST SETUP PHOTOGRAPHS OF EUT ......................................................................................................................20 5 PHOTOS OF EUT ....................................................................................................................................................21 Page 4 of 21 Report No.: AiTSZ-250306009FW7 1 TEST SUMMARY 1.1 Test Standards The tests were performed according to following standards: FCC Rules Part 15.225: Operation within the band 13.11014.010 MHz ANSI C63.10: 2013: American National Standard for Testing Unlicensed Wireless Devices 1.2 Test Summary FCC PART 15 .225 FCC Part 15.207 FCC Part 2.1049 FCC Part 15.225(a) (b) (c) FCC Part 15.225(d)/15.207 FCC Part 15.225(e) AC Power Conducted Emission 20dB Bandwidth In-band Emissions Out-of-band Emissions Frequency Stability Tolerance PASS PASS PASS PASS PASS Page 5 of 21 Report No.: AiTSZ-250306009FW7 1.3 Test Facility Test Laboratory: Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China The test facility is recognized, certified or accredited by the following organizations: FCC-Registration No.: 251906 Designation Number: CN1376 Guangdong Asia Hongke Test Technology Limited has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. IC --Registration No.: 31737 CAB identifier: CN0165 The 3m Semi-anechoic chamber of Guangdong Asia Hongke Test Technology Limited has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 31737 A2LA-Lab Cert. No.: 7133.01 Guangdong Asia Hongke Test Technology Limited has been accredited by A2LA for technical competence in the field of electrical testing, and proved to be in compliance with ISO/IEC 17025: 2017 General Requirements for the Competence of Testing and Calibration Laboratories and any additional program requirements in the identified field of testing. 1.4 Measurement uncertainty The data and results referenced in this document are true and accurate. The reader is cautioned that there may be errors within the calibration limits of the equipment and facilities. The measurement uncertainty was calculated for all measurements listed in this test report according to CISPR 16 - 4 "Specification for radio disturbance and immunity measuring apparatus and methods Part 4: Uncertainty in EMC Measurements" and is documented in the Guangdong Asia Hongke Test Technology Limited's quality system according to DIN EN ISO/IEC 17025. Furthermore, component and process variability of devices similar to that tested may result in additional deviation. The manufacturer has the sole responsibility of continued compliance of the device. Hereafter the best measurement capability for Asia Hongke laboratory is reported: Test Measurement Uncertainty Notes Power Line Conducted Emission 9KHz~30MHz ±1.20 dB (1) Radiated Emission 9KHz~30MHz ±3.10dB (1) Radiated Emission 30MHz~1GHz ±3.75dB (1) Radiated Emission 1GHz~18GHz ±3.88 dB (1) Radiated Emission 18GHz-40GHz ±3.88dB (1) RF power, conducted 30MHz~6GHz ±0.16dB (1) RF power density, conducted ±0.24dB (1) Spurious emissions, conducted ±0.21dB (1) Temperature ±1 (1) Humidity ±3% (1) DC and low frequency voltages ±1.5% (1) Time ±2% (1) Duty cycle ±2% (1) The report uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty Multiplied by a coverage factor of k=2 , providing a level of confidence of approximately 95%. Page 6 of 21 Report No.: AiTSZ-250306009FW7 2 GENGENERAL INFORMATION 2.1 Environmental conditions During the measurement the environmental conditions were within the listed ranges: Normal Temperature: 25°C Relative Humidity: 55 % Air Pressure: 101 kPa 2.2 General Description of EUT Product Name: Smart Phone Model/Type reference: Serial Model: Power Supply: Adapter information: Hardware Version: GQ5021RH Armor X32, Armor X32 Ultra, Armor X32E, Armor X32S, Armor X32 Lite, Armor X32s, Armor X32s Pro Input: DC 5V/9.0V/12.0V DC 3.87V Rechargeable Li-ion battery Model: QZ-0180AA2H Input: 100-240V AC50/60Hz 0.5A Output: 5.0V3.0A 15.0W or 9.0V2.22A 20.0W Max. or 12.0V1.67A 20.0W Max. N/A Software Version: Sample(s) Status: NFC: N/A AiTSZ-250306009-1(Normal sample) AiTSZ-250306009-2(Engineer sample) Operation frequency: 13.56MHz Modulation : ASK No. of Channel : 1 Antenna type: Loop Antenna Remark: The above DUT's information was declared by manufacturer. For more detailed features description, please refer to the manufacturer's specifications or the User's Manual.. Page 7 of 21 Report No.: AiTSZ-250306009FW7 2.3 Special Accessories Follow auxiliary equipment(s) test with EUT that provided by the manufacturer or laboratory is listed as follow: Description Manufacturer Model Serial No. Provided by Other / / / / / / / / / / / / 2.4 Equipment List for the Test No Test Equipment 1 EMI Measuring Receiver 2 Spectrum Analyzer Manufacturer R&S R&S Model No ESR FSV40 Serial No 101160 101470 3 Low Noise Pre Amplifier SCHWARZBECK BBV 9745 00282 4 Low Noise Pre Amplifier CESHENG CSKJLNA23101 CSKJLNA231016 6A A 5 Passive Loop ETS 6512 00165355 TRILOG Super 6 Broadband test SCHWARZBECK VULB9168 Antenna 7 Broadband Horn Antenna Schwarzbeck BBHA 9120D 01434 452 8 Horn Antenna 1540GHz SCHWARZBECK BBHA9170 BBHA9170367 9 6dB Attenuator JFW 50FPE-006 4360846-949-1 10 EMI Test Receiver 11 LISN 12 LISN 13 Pulse Limiter 14 RF Automatic Test system 15 Vector Signal Generator 16 Analog signal generator 17 Spectrum Analyzer R&S R&S R&S R&S TST Agilent Agilent Agilent ESPI NNLK 8129 ESH3-Z5 ESH3-Z2 TSTPASS N5182A E8257 N9020A 100771 8130179 892785/016 102789 21033016 MY50143009 MY51554256 MY51289843 18 Spectrum Analyzer Agilent N9020A MY53421570 19 Power Sensor Wideband Radio 20 communication tester 21 DC power supply Agilent R&S ZHAOXIN 8481A CMW500 RXN-305D-2 MY41097697 1201.0002K50 28070002559 22 RE Software EZ EZ-EMC_RE Ver.AIT-03A 23 CE Software EZ EZ-EMC_CE Ver.AIT-03A Cal. Date 2024.09.25 2024.09.23 2024.09.25 2024.09.25 2024.08.29 2024.08.29 2024.08.29 2024.08.28 2024.09.24 2024.09.25 2024.09.24 2024.09.23 2024.09.24 2024.09.25 2024.09.25 2024.09.25 2024.09.25 2024.09.25 2024.09.25 2024.09.24 2024.09.24 N/A N/A Cal. Due Date 2025.09.24 2025.09.22 2025.09.24 2025.09.24 2027.08.28 2027.08.28 2027.08.28 2027.08.27 2025.09.23 2025.09.24 2025.09.23 2025.09.22 2025.09.23 2025.09.24 2025.09.24 2025.09.24 2025.09.24 2025.09.24 2025.09.24 2025.09.23 2025.09.23 N/A N/A Page 8 of 21 Report No.: AiTSZ-250306009FW7 24 RF Software TST TSTPASS Version 2.0 N/A N/A 25 RF Software cesheng WCS-WCN Version 2024.6.20 N/A N/A 26 temporary antenna connector(Note) NTS R001 N/A N/A N/A Note: The temporary antenna connector is soldered on the PCB board in order to perform conducted tests and this temporary antenna connector is listed in the equipment list. Page 9 of 21 Report No.: AiTSZ-250306009FW7 3 TEST CONDITIONS AND RESULTS 3.1 Conducted Emissions Test LIMIT Frequency range (MHz) 0.15-0.5 0.5-5 5-30 Limit (dBuV) Quasi-peak 66 to 56* 56 60 Average 56 to 46* 46 50 * Decreases with the logarithm of the frequency. TEST CONFIGURATION TEST PROCEDURE 1. The equipment was set up as per the test configuration to simulate typical actual usage per the user's manual. The EUT is a tabletop system; a wooden table with a height of 0.8 meters is used and is placed on the ground plane as per ANSI C63.10:2013. 2. Support equipment, if needed, was placed as per ANSI C63.10:2013. 3. All I/O cables were positioned to simulate typical actual usage as per ANSI C63.10:2013. 4. The adapter received AC120V/60Hz power through a Line Impedance Stabilization Network (LISN) which supplied power source and was grounded to the ground plane. 5. All support equipments received AC power from a second LISN, if any. 6. The EUT test program was started. Emissions were measured on each current carrying line of the EUT using a spectrum Analyzer / Receiver connected to the LISN powering the EUT. The LISN has two monitoring points: Line 1 (Hot Side) and Line 2 (Neutral Side). Two scans were taken: one with Line 1 connected to Analyzer / Receiver and Line 2 connected to a 50 ohm load; the second scan had Line 1 connected to a 50 ohm load and Line 2 connected to the Analyzer / Receiver. 7. Analyzer / Receiver scanned from 150 KHz to 30MHz for emissions in each of the test modes. 8. During the above scans, the emissions were maximized by cable manipulation. Page 10 of 21 Report No.: AiTSZ-250306009FW7 TEST RESULTS Remark: Both 120 VAC, 50/60 Hz and 240 VAC, 50/60 Hz power supply have been tested, only the worst result of 120 VAC, 60 Hz was reported as below: Test Mode NFC Line: L Remark: Correct Factor = Insertion loss of LISN + Cable loss + Insertion loss of Pulse Limiter; Measurement Result = Reading Level +Correct Factor; Margin = Measurement Result- Limit No. Frequency Reading (MHz) (dBuV) 1 0.2625 25.82 2 0.3030 37.17 3 0.3660 33.46 4 0.3704 43.64 5 0.4650 41.49 6 0.7215 26.59 7 0.8160 40.87 8 2.4630 24.66 9 2.5080 39.86 10 3.8760 22.04 11 4.0470 37.11 12 8.5515 19.61 Correct (dB) 10.70 10.70 10.69 10.69 10.69 10.67 10.66 10.79 10.79 11.01 11.00 11.06 Result (dBuV) 36.52 47.87 44.15 54.33 52.18 37.26 51.53 35.45 50.65 33.05 48.11 30.67 Limit (dBuV) 51.35 60.16 48.59 58.49 56.60 46.00 56.00 46.00 56.00 46.00 56.00 50.00 Margin (dB) -14.83 -12.29 -4.44 -4.16 -4.42 -8.74 -4.47 -10.55 -5.35 -12.95 -7.89 -19.33 Remark AVG QP AVG QP QP AVG QP AVG QP AVG QP AVG Test Mode Page 11 of 21 Report No.: AiTSZ-250306009FW7 NFC Line: N Remark: Correct Factor = Insertion loss of LISN + Cable loss + Insertion loss of Pulse Limiter; Measurement Result = Reading Level +Correct Factor; Margin = Measurement Result- Limit No. Frequency Reading (MHz) (dBuV) 1 0.3660 40.57 2 0.3660 31.68 3 0.4650 41.65 4 0.4783 29.52 5 1.1580 39.12 6 1.3965 25.17 7 2.4000 38.35 8 2.4180 26.02 9 3.6960 24.64 10 3.7320 35.87 11 7.5750 23.69 12 8.3850 33.67 Correct (dB) 10.68 10.68 10.69 10.69 10.66 10.69 10.78 10.78 10.98 10.99 11.03 11.04 Result (dBuV) 51.25 42.36 52.34 40.21 49.78 35.86 49.13 36.80 35.62 46.86 34.72 44.71 Limit (dBuV) 58.59 48.59 56.60 46.37 56.00 46.00 56.00 46.00 46.00 56.00 50.00 60.00 Margin (dB) -7.34 -6.23 -4.26 -6.16 -6.22 -10.14 -6.87 -9.20 -10.38 -9.14 -15.28 -15.29 Remark QP AVG QP AVG QP AVG QP AVG AVG QP AVG QP Page 12 of 21 Report No.: AiTSZ-250306009FW7 3.2 Radiated Emissions Limit a The field strength of any emissions within the band 13.55313.567 MHz shall not exceed 15,848 microvolts/ meter at 30 meters. b Within the bands 13.41013.553 MHz and 13.56713.710 MHz, the field strength of any emissions shall not exceed 334 microvolts/meter at 30 meters. c Within the bands 13.11013.410 MHz and 13.71014.010 MHz the field strength of any emissions shall not exceed 106 microvolts/meter at 30 meters. d The field strength of any emissions appearing outside of the 13.110 14.010 MHz band shall not exceed the general radiated emission limits in §15.209. Radiated emission limits Frequency (MHz) Distance (Meters) Radiated (dBuV/m) 0.009-0.49 3 20log(2400/F(KHz))+40log(300/3) Radiated (V/m) 2400/F(KHz) 0.49-1.705 3 20log(24000/F(KHz))+ 40log(30/3) 24000/F(KHz) 1.705-13.110 3 13.110-13.410 3 69.54 30 80.50 106 13.410-13.553 3 90.47 334 13.553-13.567 3 124.00 15848 13.567-13.710 3 13.710-14.010 3 90.47 334 80.50 106 14.010-30.0 3 69.54 30 30-88 3 40.0 100 88-216 3 216-960 3 43.5 150 46.0 200 Above 960 3 54.0 500 TEST CONFIGURATION (A) Radiated Emission Test Set-Up, Frequency Below 30MHz (B) Radiated Emission Test Set-Up, Frequency below 1000MHz Page 13 of 21 Report No.: AiTSZ-250306009FW7 Test Procedure 1. Below 1GHz measurement the EUT is placed on a turntable which is 0.8m above ground plane, and above 1GHz measurement EUT was placed on a low permittivity and low loss tangent turn table which is 1.5m above ground plane. 2. Maximum procedure was performed by raising the receiving antenna from 1m to 4m and rotating the turn table from 0 to 360 to acquire the highest emissions from EUT 3. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 4. Repeat above procedures until all frequency measurements have been completed. 5. Radiated emission test frequency band from 9KHz to 1GHz. 6. The distance between test antenna and EUT as following table states: Test Frequency range 9KHz-30MHz 30MHz-1GHz Test Antenna Type Active Loop Antenna Bilog Antenna Test Distance 3 3 7. Setting test receiver/spectrum as following table states: Test Frequency range 9KHz-150KHz 150KHz-30MHz 30MHz-1GHz Test Receiver/Spectrum Setting RBW=200Hz/VBW=3KHz,Sweep time=Auto RBW=9KHz/VBW=100KHz,Sweep time=Auto RBW=120KHz/VBW=1000KHz,Sweep time=Auto Detector QP QP QP TEST RESULTS Below 30MHz Frequency(MHz): Frequency Meter Reading (MHz) (dBV) 8.948 14.77 13.376 21.17 13.49 33.93 13.562 40.91 13.58 33.59 13.997 22.06 20.549 13.59 Page 14 of 21 Report No.: AiTSZ-250306009FW7 13.56MHz Factor Emission Level (dB/m) (dBV/m) 22.03 36.80 22.58 43.75 22.60 56.53 22.62 63.53 22.62 56.21 22.7 44.76 22.75 36.34 Polarity: Limits (dBV/m) 69.54 80.50 90.47 124.00 90.47 80.50 69.54 Antenna Position 0 Margin (dB) -32.74 -36.75 -33.94 -60.47 -34.26 -35.74 -33.20 Detector Type PEAK PEAK PEAK PEAK PEAK PEAK PEAK Frequency(MHz): Frequency Meter Reading (MHz) (dBV) 13.56MHz Factor Emission Level (dB/m) (dBV/m) Polarity: Limits (dBV/m) Antenna Position 90 Margin (dB) Detector Type 4.922 13.59 22.47 36.06 69.54 -33.48 PEAK 13.111 21.34 22.53 43.87 80.50 -36.63 PEAK 13.457 33.22 22.60 55.82 90.47 -34.65 PEAK 13.562 40.38 22.62 63.00 124.00 -61.00 PEAK 13.632 32.00 22.63 54.63 90.47 -35.84 PEAK 13.723 20.75 22.65 43.40 80.50 -37.10 PEAK REMARKS: 1. Emission level (dBuV/m) = Reading (dBuV)+ Factor (dB/m) 2. Factor (dB/m) = Antenna Factor (dB/m)+Cable Factor (dB) 3. Margin value = Emission level- Limit value. 4. Other emission levels are attenuated 20dB below the limit and not recorded in report. For 30MHz-1GHz Test mode: Page 15 of 21 Report No.: AiTSZ-250306009FW7 NFC Polarization: Horizontal Remark: Emission Level = Reading + Factor; Factor = Antenna Factor + Cable Loss Pre-amplifier; Margin= Emission Level - Limit. No. Frequency (MHz) Reading (dBuV) Factor (dB/m) Level (dBuV/m) Limit (dBuV/m) Margin (dB) Det. 1 37.1550 36.81 -16.88 19.93 40.00 -20.07 QP 2 139.8505 41.86 -17.33 24.53 43.50 -18.97 QP 3 175.6516 45.33 -17.68 27.65 43.50 -15.85 QP 4 336.0350 41.56 -16.03 25.53 46.00 -20.47 QP 5 574.6258 37.20 -10.39 26.81 46.00 -19.19 QP 6 935.5461 37.04 -3.90 33.14 46.00 -12.86 QP Test mode: Page 16 of 21 Report No.: AiTSZ-250306009FW7 NFC Polarization: Vertical Remark: Emission Level = Reading + Factor; Factor = Antenna Factor + Cable Loss Pre-amplifier; Margin= Emission Level - Limit. No. Frequency (MHz) Reading (dBuV) Factor (dB/m) Level (dBuV/m) Limit (dBuV/m) Margin (dB) Det. 1 35.3750 44.66 -17.15 27.51 40.00 -12.49 QP 2 64.8863 42.66 -18.08 24.58 40.00 -15.42 QP 3 168.4137 47.75 -16.79 30.96 43.50 -12.54 QP 4 297.2240 41.18 -17.03 24.15 46.00 -21.85 QP 5 584.7894 33.71 -10.12 23.59 46.00 -22.41 QP 6 935.5461 36.57 -3.90 32.67 46.00 -13.33 QP Page 17 of 21 Report No.: AiTSZ-250306009FW7 3.3 20dB Bandwidth Limit No limit for 20dB bandwidth. Test Procedure The 20dB bandwidth is measured with a spectrum analyzer connected via a receive antenna placed near the EUT while the EUT is operating in transmission mode. The 20dB bandwidth is defined as the total spectrum the power of which is higher than peak power minus 20dB. Test Configuration Test Results Modulation ASK EUT Spectrum Analyzer Frequency(MHz) 13.56 20dB bandwidth (KHz) 0.111 99%dB bandwidth (KHz) 0.378 Result Pass Page 18 of 21 Report No.: AiTSZ-250306009FW7 3.4 Frequency Stability LIMIT The frequency tolerance of the carrier signal shall be maintained within ±0.01% of the operating frequency over a temperature variation of -20 degrees to +50 degrees C at normal supply voltage, and for a variation in the primary supply voltage from 85% to 115% of the rated supply voltage at a temperature of 20 degrees C. TEST CONFIGURATION TEST PROCEDURE 1. The equipment under test was connected to an external DC power supply and input rated voltage. 2. RF output was connected to a frequency counter or spectrum analyzer via feed through attenuators. 3. The EUT was placed inside the temperature chamber. 4. Set the spectrum analyzer RBW low enough to obtain the desired frequency resolution and measure EUT 20 operating frequency as reference frequency. 5. Turn EUT off and set the chamber temperature to 20. After the temperature stabilized for approximately 30 minutes recorded the frequency. 6. Repeat step measure with 10 increased per stage until the highest temperature of +50 reached. 7. Reduce the input voltage to specified extreme voltage variation (+/- 15%) or endpoint, record the maximum frequency change. TEST RESULTS Voltage ( V ) 3.87 4.45 3.29 Page 19 of 21 Report No.: AiTSZ-250306009FW7 Reference Frequency: 13.56MHz Temperature () Frequency (Hz) Frequency Deviation(Hz) +20(Ref) 13.560084 84 -20 13.560164 164 -10 13.560123 123 0 13.560194 194 +10 13.560127 127 +20 13.560113 113 +25 13.560117 117 +30 13.560155 155 +40 13.560164 164 +50 13.560162 162 +20 13.560182 182 +20 13.560129 129 Deviation (%) 0.000619% 0.001209% 0.000907% 0.001431% 0.000937% 0.000833% 0.000863% 0.001143% 0.001209% 0.001195% 0.001342% 0.000951% Page 20 of 21 4 Test Setup Photographs of EUT Report No.: AiTSZ-250306009FW7 Page 21 of 21 Report No.: AiTSZ-250306009FW7 5 Photos of EUT Please refer to test Report No.: AiTSZ-250306009FW1. ********************** End of Report **********************Microsoft Office Word Aspose.Words for .NET 15.1.0.0