Manuals+

Trenz Electronic TEB0835 Carrier Board Schematics

This document provides the schematics and revision history for the Trenz Electronic TEB0835 carrier board.

Variant B Compatibility

Variant B is compatible with modules that have VIN = 5V to 12V.

Legal Notices

Regarding the usage of our schematics and alike documentation for Trenz baseboard TEB0835. Baseboard is Open Source Hardware and therefore free to use, adapt and can be modified to suit your needs as described in the "The MIT License". Permission is hereby granted, free of charge, to any person obtaining a copy of this hardware and associated documentation files (the "Product"), to deal in the Product without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Product, and to permit persons to whom the Product is furnished to do so. Schematics and other handouts serve for informational purposes only!

Title: Legal Notices

Design drawn by: IG

Checked by: MR

Assembly variant: B

Created by: IG

Modified by: IG

Modified at: 05.06.2025

Date: 2024-05-14

Copyright: Trenz Electronic GmbH

Filename: Legal Notices.SchDoc

Revision History

This section details the changes made to the TEB0835 board across various revisions.

Revision -01

Revision -02

  1. All module's mount holes are connected to GND.
  2. CLK_Connectors. Added baluns for each clock inputs.
  3. Internal DSPLL is changed on SI5395A-A-GM.
  4. Added ability to use internal DSPLL as a source for each clock.
  5. Added clock inputs CLKIN1, CLKIN2 and clock outputs OUT1, OUT2 connected to DSPLL.
  6. All clock traces are matched with tolerance 0.2 mm.
  7. Lengths of inputs ADC0, ADC2, ADC4, ADC6 are matched with tolerance 0.2 mm.
  8. Lengths of outputs DACO and DAC2 are matched with tolerance 0.2 mm.
  9. Lengths of outputs DAC4, DAC5, DAC6, DAC7 are matched with tolerance 0.2 mm.
  10. In REV02: FTDI is powered from 3.3V_Module.
  11. Signal PLL_INTR_N is removed.
  12. Signal BOARD_PG is renamed in MODULE_PG.
  13. Added ability to select enable signal for internal DC-DCs 3.3V and 1.8V.
  14. Added JTAG connector J40.
  15. Added VBAT schematic. Added a holder for CR1220 3V battery.
  16. Resistor R4 changed to 10K (was 1K).

Revision -03

  1. Added "Legal Notices" page.
  2. Added "Power Diagram" page.
  3. Added "Clock Diagram" page.
  4. Page "TEB0835" is updated:
    • Added a table of I2C Slaves.
    • Added PCIe-bracket MECH1.
    • Added four plastic standoffs MP1-MP4 (D01468).
  5. Page "ADC_Input_Connectors_1":
    • Connector designators are changed: J1 → XS1, J5 → XS2, J3 → XS3, J7 → XS4.
    • Type of RF connectors XS1, XS2, XS3, XS4 are changed: SMA (5-1814400-1) → SMP (734060241).
    • Balun designators are changed: T2 → TR1, T6 → TR2, T4 → TR3, T8 → TR4.
    • Type of the baluns TR1, TR2, TR3, TR4 are changed: TCM2-33WX+ → TCM2-43X+.
    • Resistors are changed: R10 (DNP) → R10 (1 MOhm), R11 (DNP) → R11 (1 MOhm), R7 (590 Ohm) → R7 (1 MOhm), R6 (17,4 Ohm) → R6 (0 Ohm), R9 (17,4 Ohm) → R9 (0 Ohm), R8 (590 Ohm) → R8 (1 MOhm),R38 (DNP) → R38 (1 MOhm), R39 (DNP) → R39 (1MOhm), R35 (560 Ohm) → R35 (1MOhm), R34 (17,4 Ohm) → R34 (0 Ohm), R37 (17,4 Ohm) → R37 (0 Ohm), R36 (590 Ohm) → R36 (1 MOhm), R24 (DNP) → R24 (1 MOhm), R25 (DNP) → R25 (1 MOhm), R21 (590 Ohm) → R21 (1 MOhm), R20 (17,4 Ohm) → R20 (0 Ohm), R23 (17,4 Ohm) → R23 (0 Ohm), R22 (590 Ohm) → R22 (1 MOhm), R52 (DNP) → R52 (1 MOhm), R53 (DNP) → R53 (1 MOhm), R49 (590 Ohm) → R49 (1 MOhm), R48 (17,4 Ohm) → R48 (0 Ohm), R51 (17,4 Ohm) → R51 (0 Ohm), R50 (590 Ohm) → R50 (1 MOhm).
    • Net names are changed: ADC0_IN → ADC_INO, ADC4_IN → ADC_IN1, ADC2_IN → ADC_IN2, ADC6_IN → ADC_IN2.
    • Net names are changed: ADC_S4 → ADC_S1, ADC_S6 → ADC_S3.
    • Net names are changed: ADC_B4_(N/P) → ADC_B1_(N/P), ADC_C4_(N/P) → ADC_C1_(N/P), ADC4_(N/P) → ADC1_(N/P), ADC_B6_(N/P) → ADC_B3_(N/P), ADC_C6_(N/P) → ADC_C3_(N/P), ADC6_(N/P) → ADC3_(N/P).
    • Added mech part Shield1 (3670412).
  6. Page "ADC_Input_Connectors_2":
    • Connector designators are changed: J2 → XS5, J4 → XS6, J6 → XS7, J8 → XS8.
    • Type of RF connectors XS5, XS6, XS7, XS8 are changed: SMA (5-1814400-1) → SMP (734060241).
    • Balun designators are changed: T3 → TR5, T5 → TR6, T7 → TR7, T9 → TR8.
    • Type of the baluns TR5, TR6, TR7, TR8 are changed: TCM2-33WX+ → TCM2-43X+.
    • Resistors are changed: R17 (DNP) → R17 (1 MOhm), R18 (DNP) → R18 (1 MOhm), R14 (590 Ohm) → R14 (1 MOhm), R13 (17,4 Ohm) → R13 (0 Ohm), R16 (17,4 Ohm) → R16 (0 Ohm), R15 (590 Ohm) → R15 (1 MOhm), R45 (DNP) → R45 (1 MOhm), R46 (DNP) → R46 (1 MOhm), R42 (590 Ohm) → R42 (1 MOhm), R41 (17,4 Ohm) → R41 (0 Ohm), R44 (17,4 Ohm) → R44 (0 Ohm), R43 (590 Ohm) → R43 (1 MOhm), R31 (DNP) → R31 (1 MOhm), R32 (DNP) → R32 (1 MOhm), R28 (590 Ohm) → R28 (1 MOhm), R27 (17,4 Ohm) → R27 (0 Ohm), R30 (17,4 Ohm) → R30 (0 Ohm), R29 (590 Ohm) → R29 (1 MOhm), R59 (DNP) → R59 (1 MOhm), R60 (DNP) → R60 (1 MOhm), R56 (590 Ohm) → R56 (1 MOhm), R55 (17,4 Ohm) → R55 (0 Ohm), R58 (17,4 Ohm) → R58 (0 Ohm), R57 (590 Ohm) → R57 (1 MOhm).
    • Net names are changed: ADC1_IN → ADC_IN4, ADC3_IN → ADC_IN5, ADC5_IN → ADC_IN6, ADC7_IN → ADC_IN7.
    • Net names are changed: ADC_S1 → ADC_S4, ADC_S3 → ADC_S5, ADC_S5 → ADC_S6.
    • Net names are changed: ADC_B1_(N/P) → ADC_B4_(N/P), ADC_C1_(N/P) → ADC_C4_(N/P), ADC1_(N/P) → ADC4_(N/P), ADC_B3_(N/P) → ADC_B5_(N/P), ADC_C3_(N/P) → ADC_C5_(N/P), ADC3_(N/P) → ADC5_(N/P), ADC_B5_(N/P) → ADC_B6_(N/P), ADC_C5_(N/P) → ADC_C6_(N/P), ADC5_(N/P) → ADC6_(N/P).
    • Added mech part Shield2 (3670412).
  7. Page "DAC_Output_Connectors_1":
    • Connector designators are changed: J9 → XS9, J10 → XS10, J11 → XS11, J12 → XS12.
    • Type of RF connectors XS9, XS10 are changed: SMA (5-1814400-1) → SMP (734060241).
    • Type of RF connectors XS11, XS12 are changed: U.FL (U.FL-R-SMT-1) → SMP (734060241).
    • Balun designators are changed: T10 → TR9, T12 → TR10, T13 → TR11, T11 → TR12.
    • Type of the baluns TR9, TR10, TR11, TR12 are changed: TCM2-33WX+ → TCM2-43X+.
    • Net names are changed: DACO_OUT → DAC_OUT0, DAC1_OUT → DAC_OUT1, DAC2_OUT→ DAC_OUT2, DAC3_OUT → DAC_OUT3.
    • Resistors are changed: R66 (DNP) → R66 (1 MOhm), R67 (DNP) → R67 (1 MOhm), R63 (590 Ohm) → R63 (1 MOhm), R62 (17,4 Ohm) → R62 (0 Ohm), R65 (17,4 Ohm) → R65 (0 Ohm), R64 (590 Ohm) → R64 (1 MOhm), R73 (DNP) → R73 (1 MOhm), R74 (DNP) → R74 (1 MOhm), R70 (590 Ohm) → R70 (1 MOhm), R69 (17,4 Ohm) → R69 (0 Ohm), R72 (17,4 Ohm) → R72 (0 Ohm), R71 (590 Ohm) → R71 (1 MOhm), R80 (DNP) → R80 (1 MOhm), R81 (DNP) → R81 (1 MOhm), R77 (590 Ohm) → R77 (1 MOhm), R76 (17,4 Ohm) → R76 (0 Ohm), R79 (17,4 Ohm) → R79 (0 Ohm), R78 (590 Ohm) → R78 (1 MOhm), R87 (DNP) → R87 (1 MOhm), R88 (DNP) → R88 (1 MOhm), R84 (590 Ohm) → R84 (1 MOhm), R83 (17,4 Ohm) → R83 (0 Ohm), R86 (17,4 Ohm) → R86 (0 Ohm), R85 (590 Ohm) → R85 (1 MOhm).
    • Added mech part Shield2 (3670412).
  8. Page "DAC_Output_Connectors_2":
    • Connector designators are changed: J13 → XS13, J14 → XS14, J15 → XS15, J16 → XS16.
    • Type of RF connectors XS13, XS14, XS15, XS16 are changed: U.FL (U.FL-R-SMT-1) → SMP (734060241).
    • Balun designators are changed: T14 → TR13, T15 → TR14, T16 → TR15, T17 → TR16.
    • Type of the baluns TR13, TR14, TR15, TR16 are changed: TCM2-33WX+→ TCM2-43X+.
    • Net names are changed: DAC4_OUT → DAC_OUT4, DAC5_OUT → DAC_OUT5, DAC6_OUT → DAC_OUT6, DAC7_OUT → DAC_OUT7.
    • Resistors are changed: R94 (DNP) → R94 (1 MOhm), R95 (DNP) → R95 (1 MOhm), R91 (590 Ohm) → R91 (1 MOhm), R90 (17,4 Ohm) → R90 (0 Ohm), R93 (17,4 Ohm) → R93 (0 Ohm), R92 (590 Ohm) → R92 (1 MOhm), R101 (DNP) → R101 (1 MOhm), R102 (DNP) → R102 (1 MOhm), R98 (590 Ohm) → R98 (1 MOhm), R97 (17,4 Ohm) → R97 (0 Ohm), R100 (17,4 Ohm) → R100 (0 Ohm), R99 (590 Ohm) → R99 (1 MOhm), R108 (DNP) → R108 (1 MOhm), R109 (DNP) → R109 (1 MOhm), R105 (590 Ohm) → R105 (1 MOhm), R104 (17,4 Ohm) → R104 (0 Ohm), R107 (17,4 Ohm) → R107 (0 Ohm), R106 (590 Ohm) → R106 (1 MOhm), R115 (DNP) → R115 (1 MOhm), R116 (DNP) → R116 (1 MOhm), R112 (590 Ohm) → R112 (1 MOhm), R111 (17,4 Ohm) → R111 (0 Ohm), R114 (17,4 Ohm) → R114 (0 Ohm), R113 (590 Ohm) → R113 (1 MOhm).
  9. Page "CLK_Connectors_1":
    • R161, R166, R175, R226, R229, R232 (DNP) → (1 MOhm).
  10. Page "CLK_Connectors_2":
    • Type of J36 connector are changed: U.FL (U.FL-R-SMT-1) → SMA (R125426000).
    • Added RFSOC PL synchronisation scheme via B65_L11_(P/N) from PLL CLKOUT8_(P/N). Also added possibility of synchronisation from external source via J42, R158, T34, C124, C126.
    • Added RFSOC PL synchronisation scheme via B65_L12_(P/N) from PLL CLKOUT7_(P/N). Also added possibility of synchronisation from external source via J43, R242, T35, C129, C131.
    • Added RFSoC Module PLL synchronisation. External clock can be applied to EXT_CLK_IN1_(P/N) via SMA J46 (R125426000), R224, T36 or R287.
  11. Page "B2B_JB1":
    • B2B connector designator is changed: J17 → JB1.
    • Module power rail is renamed to V_Module.
    • Added TP33.
  12. Page "B2B_JB2":
    • B2B connector designator is changed: J18 → JB2.
    • Pins 1 and 2 of JB2 connected to GND.
    • Clock CLKA_(P/N) (JB2:36 and JB2:38) connected to J45 (A2 and B1).
    • B65 L1 (P/N) (JB2:15 and JB2:17) connected to J45 (B7 and A8).
    • B65_L2_(P/N) (JB2:6 and JB2:4) connected to J45 (B12 and A12).
    • B65_L3_(P/N) (JB2:3 and JB2:5) connected to J45 (B12 and A12).
    • B65_L4_(P/N) (JB2:16 and JB2:14) connected to J45 (B16 and A17).
    • B65 L5 (P/N) (JB2:10 and JB2:8) connected to J45 (B15 and A15).
    • B65_L6_(P/N) (JB2:11 and JB2:13) connected to J45 (B9 and A9).
    • B65 L8 (P/N) (JB2:19 and JB2:21) connected to J45 (B6 and A6).
    • B65_L9_(P/N) (JB2:7 and JB2:9) connected to J45 (B10 and A11).
    • B65_L11_(P/N) (JB2:22 and JB2:20) connected to CLKOUT8 on page "CLK_Connectors_2".
    • B65_L12_(P/N) (JB2:18 and JB2:16) connected to CLKOUT7 on page "CLK_Connectors_2".
    • B65_L13_(P/N) (JB2:25 and JB2:23) connected to CLKOUT9A on page "DSPLL".
    • 665_L16_(P/N) (JB2:24 and JB2:26) connected to J45 (B18 and A18).
    • EXT_CLK_IN1_(P/N) connected to balun T36 on page "CLK_Connectors_2".
    • Schematic of battery supply is changed: diode D13 moved to LDO U18 input, C86 (4,7uF) → C86 (470nF), U18 (TPS780180300) → U18 (TPS7A0212PDBVR).
    • Status LEDs D6-D10 are renamed to LED0 LED3, D11 is removed. The LEDs are moved to "EXT_Connectors" page.
    • Resistors are changed: R216-R221 (330 Ohms) → R216-R221 (33 Ohms).
  13. Page "POWER":
    • Capacitor C37 are changed 10nF → 1nF to adjust inrush current.
    • Transistors T18-T21 (SIS444DN-T1-GE3 - EOL) are replaced with SIS4604LDN-T1-GE3.
  14. Page "PWR_1V8":
    • DC-DC U1 TPS82085SIL converter replaced by TPS62913RPUR for noise reduction and VIN 12V capability.
  15. Page "PWR_3V3":
    • DC-DC U4 TPS82085SIL converter replaced by TPS62913RPUR for noise reduction and VIN 12V capability.
  16. Page "PWR_5V":
    • Added a switch SW3 to disable DC-DC U8.
    • Added a switch SW2 to enable discontinuous mode of DC-DC U8.
    • Added inductors L38 and L39 for connecting V_MODULE to 12V.
  17. Page "I2C_MUX":
    • Added pull-up resistors R262 - R265.
  18. Page "SD":
    • The load switch Q1 is replaced by MP5077GG-Z with integrated overload protection circuitry.
  19. Page "FTDI":
    • Added LDO regulator U19, diodes D6, D7, C217, L19 to provide 3.3V_FTDI voltage.
    • Added JTAG switch U14.
    • Resistors R237-R240 are removed.
    • UART buffer U13 is replaced SN74LVC1G07DRL→ SN74AVC4T774RSVR.
    • Added USB filter L25.
  20. Page "MicroUSB":
    • Resistor R223 is DNP by default.
  21. Page DSPLL:
    • CLKOUT7 connected to B65 L12.
    • CLKOUT8 connected to B65 L11.
    • CLKOUT9 connected to SYSREFCLK.
    • CLKOUT9A connected toB65 L13.
    • CLKIN3 doesn't use.
  22. Page FireFly:
    • Added detect network R246-R383 according to FireFly specification.
  23. Page FF_0_1:
    • Added power switch Q2.
    • Added terminators R296-R299, RR302,R303, R307-R310, R312, R313, R317, R320, R403-R05, R408.
    • Added a slide switch S7 for FireFly configuration.
    • Added pull-up resistors R288, R289, R390, R387, R409, R410.
  24. Added page EXT_Connectors:
    • Added MIO connector J44 and GPIO connector J45.
    • Added transistors T2, T37, T38.
    • Added a lightpipe LP1.
  25. Changed screws MECH3, MECH4 from metric M3 to inch UNC4-40 1/4".
  26. Added covers MECH2; MECH5 3671412 for Shield1 and Shield2.
  27. Resistor R181 replaced with 0 Ohm to switch U8 in discontinuos mode of operation.
  28. Capacitors C62, C63, C64 are marked as DNP for noise reduction.

Title: Revision_Changes

Number: TEB0835

Date: 2025-04-29

Copyright: Trenz Electronic GmbH

Filename: Revision_Changes_2.SchDoc

Power-on sequencing

This diagram illustrates the power-on sequencing of the TEB0835 carrier board.

Supported Voltage Ranges:

Power RailDirectionRangeToleranceDescriptionNote
12V_input_AIN12V±10%External PowerMiniFit 6-pin conn
12V_input_BIN12V±10%External PowerPCIe Edge conn
V_MODULEOUT5V±3%Micromodule Power12V±10% (Option)
1V8OUT1.8V±3%MicroUSB
3.3VOUT3.3V±3%J44, J45 FireFly conn
3.3V_SDOUT3.3V±3%J28 SD Card Socket
1.8VOUT1.8V±3%J44, J45 FireFly conn
FF0_VCCOUT1.8V±3%J44 FireFly conn
FF1_VCCOUT1.8V±3%J45 FireFly conn

Title: Power_Diagram

Number: TEB0835

Date: 2024-05-14

Copyright: Trenz Electronic GmbH

Filename: Power_Diagram.SchDoc

Clock Diagram

This diagram shows the clock distribution and connections for the TEB0835 carrier board and TE0835-03 RFSOC module.

Title: Clock_Diagram

Number: TEB0835

Date: 2024-12-17

Copyright: Trenz Electronic GmbH

Filename: Clock_Diagram.SchDoc

System Overview

This diagram provides a high-level overview of the TEB0835 system, showing the main components and their interconnections.

Table of I2C Addresses:

I2C AddressDesignatorDescription
0x70U7I2C Multiplexer
0x4CU9FAN Controller
0x68U5PLL

Special notes:

Title: TEB0835

Number: TEB0835

Date: 2025-05-19

Copyright: Trenz Electronic GmbH

Filename: TEB0835.SchDoc

ADC Input Connectors 1

Schematic for ADC Input Connectors 1.

Title: ADC_Input_Connectors_1

Number: TEB0835

Date: 2025-04-29

Copyright: Trenz Electronic GmbH

Filename: ADC_Input_Connectors_1.SchDoc

ADC Input Connectors 2

Schematic for ADC Input Connectors 2.

Title: ADC_Input_Connectors_2

Number: TEB0835

Date: 2024-12-17

Copyright: Trenz Electronic GmbH

Filename: ADC_Input_Connectors_2.SchDoc

DAC Output Connectors 1

Schematic for DAC Output Connectors 1.

Title: DAC_Output_Connectors_1

Number: TEB0835

Date: 2025-04-29

Copyright: Trenz Electronic GmbH

Filename: DAC_Output_Connectors_1.SchDoc

DAC Output Connectors 2

Schematic for DAC Output Connectors 2.

Title: DAC_Output_Connectors_2

Number: TEB0835

Date: 2024-12-17

Copyright: Trenz Electronic GmbH

Filename: DAC_Output_Connectors_2.SchDoc

CLK Connectors 1

Schematic for Clock Connectors 1.

Title: CLK_Connectors_1

Number: TEB0835

Date: 2024-12-17

Copyright: Trenz Electronic GmbH

Filename: CLK_Connectors_1.SchDoc

CLK Connectors 2

Schematic for Clock Connectors 2.

Title: CLK_Connectors_2

Number: TEB0835

Date: 2024-12-17

Copyright: Trenz Electronic GmbH

Filename: CLK_Connectors_2.SchDoc

B2B JB1

Schematic for the B2B JB1 connector.

Title: B2B JB1

Number: TEB0835

Date: 2025-03-28

Copyright: Trenz Electronic GmbH

Filename: B2B_JB1.SchDoc

B2B JB2

Schematic for the B2B JB2 connector.

Title: B2B JB2

Number: TEB0835

Date: 2025-03-27

Copyright: Trenz Electronic GmbH

Filename: B2B_JB2.SchDoc

POWER

Schematic for the power supply circuitry.

Title: POWER

Number: TEB0835

Date: 2024-12-17

Copyright: Trenz Electronic GmbH

Filename: POWER.SchDoc

PWR_1V8

Schematic for the 1.8V power supply.

Title: PWR_1V8

Number: TEB0835

Date: 2024-12-17

Copyright: Trenz Electronic GmbH

Filename: PWR_1V8.SchDoc

PWR_3V3

Schematic for the 3.3V power supply.

Title: PWR_3V3

Number: TEB0835

Date: 2024-12-17

Copyright: Trenz Electronic GmbH

Filename: PWR_3V3.SchDoc

PWR_5V

Schematic for the 5V power supply.

Title: PWR_5V

Number: TEB0835

Date: 2025-06-05

Copyright: Trenz Electronic GmbH

Filename: PWR_5V.SchDoc

I2C_MUX

Schematic for the I2C multiplexer.

Title: I2C_MUX

Number: TEB0835

Date: 2024-12-17

Copyright: Trenz Electronic GmbH

Filename: I2C_MUX.SchDoc

SD

Schematic for the SD card interface.

Title: SD

Number: TEB0835

Date: 2024-12-17

Copyright: Trenz Electronic GmbH

Filename: SD.SchDoc

FTDI

Schematic for the FTDI interface.

Title: FTDI

Number: TEB0835

Date: 2024-12-17

Copyright: Trenz Electronic GmbH

Filename: FTDI.schdoc

MicroUSB

Schematic for the MicroUSB connector.

Title: MicroUSB

Number: TEB0835

Date: 2024-12-17

Copyright: Trenz Electronic GmbH

Filename: MicroUSB.SchDoc

ETH-PHY

Schematic for the Ethernet PHY interface.

Title: ETH-PHY

Number: TEB0835

Date: 2024-12-17

Copyright: Trenz Electronic GmbH

Filename: ETH-PHY.SchDoc

DSPLL

Schematic for the Digital Synthesized Phase-Locked Loop (DSPLL).

Title: DSPLL

Number: TEB0835

Date: 2024-12-17

Copyright: Trenz Electronic GmbH

Filename: DSPLL.SchDoc

FireFly

Schematic for the FireFly interface.

Title: FireFly

Number: TEB0835

Date: 2024-03-06

Copyright: Trenz Electronic GmbH

Filename: FireFly.SchDoc

FF_0_1

Schematic for FF_0_1.

Title: FF_0_1

Number: TEB0835

Date: 2024-03-06

Copyright: Trenz Electronic GmbH

Filename: FF_0_1.SchDoc

EXT_Connectors

Schematic for the external connectors.

Title: EXT_Connectors

Number: TEB0835

Date: 2024-12-17

Copyright: Trenz Electronic GmbH

Filename: EXT_Connectors.SchDoc

Models: PCIe, TEB0835 Baseboard, TEB0835, PCIe Baseboard, Baseboard

File Info : application/pdf, 28 Pages, 7.70MB

PDF preview unavailable. Download the PDF instead.

SCH-TEB0835-03-B 3-Heights(TM) PDF to PDF-A Converter API 4.5.24.7 (http://www -tools.com)

Related Documents

PreviewTrenz Electronic TEB0835 Carrier Board Schematics
Detailed schematics for the Trenz Electronic TEB0835 carrier board, outlining its electrical connections, component layouts, and revision history.
PreviewTEB0835-03 Carrier Board Technical Overview
Detailed technical information and specifications for the TEB0835-03 carrier board from Trenz Electronic, including its features, connectors, and operational parameters.
PreviewTrenz Electronic TE0725LP FPGA Module Technical Overview and Schematics
Detailed technical documentation and schematics for the Trenz Electronic TE0725LP FPGA module, including system overview, pin assignments, power diagrams, and configuration modes.
PreviewTrenz TE0725LP FPGA Module: Schematics and Technical Information
This document provides detailed schematics, revision history, system overview, and technical specifications for the Trenz Electronic TE0725LP FPGA module. It includes information on power sequencing, voltage ranges, connector pinouts, and FPGA configuration modes.
PreviewTEB0835 FPGA Board Technical Overview
A technical overview of the TEB0835 FPGA board, detailing its features, connectivity, and specifications for developers and engineers.
PreviewTrenz Electronic TE0725LP FPGA Module Technical Documentation and Schematics
Comprehensive technical documentation for the Trenz Electronic TE0725LP FPGA module, featuring system overview, power management details, connector pinouts, FPGA configuration modes, and detailed schematics for various FPGA banks and power supplies.
PreviewTrenz Electronic TE0725LP Module Schematics and Documentation
Comprehensive documentation for the Trenz Electronic TE0725LP FPGA System-on-Module, including detailed schematics, system overview, power sequencing, voltage ranges, connector pinouts, and revision history.
PreviewTrenz Electronic 2025 Product Catalogue: Forging FPGA Frontiers
Explore the comprehensive 2025 Product Catalogue from Trenz Electronic, featuring a wide range of FPGA solutions including SoCs, SoMs, Carrier boards, Development boards, and Electronic Design Services. Discover innovative products for FPGA development.