User Guide for WyreStorm models including: SW-510-TX, 4-input 4K UHD Switching HDBaseT Transmitter, SW-510-TX 4-input 4K UHD Switching HDBaseT Transmitter, 4K UHD Switching HDBaseT Transmitter, Switching HDBaseT Transmitter, HDBaseT Transmitter, Transmitter
Quickstart Guide. IMPORTANT! Installation Requirements. • Read through the Wiring and Connections section for important wiring.
SW-510-TX | Exertis Pro AV Deutschland
File Info : application/pdf, 4 Pages, 878.33KB
DocumentDocument4-input 4K UHD Switching HDBaseT Transmitter with USB host/device (4K: 100m/328ft)
SW-510-TX
Quickstart Guide
WyreStorm recommends reading through this document in its entirety to become familiar with the product's features before beginning the installation process.
IMPORTANT! Installation Requirements · Read through the Wiring and Connections section for important wiring
guidelines before creating or choosing premade cables. · While this product supports CEC, WyreStorm cannot guarantee
compatibility with all forms of CEC communication. · Visit the product page to download the latest firmware, document version,
additional documentation, and configuration tools.
Information and Parts Required for Installation This transmitter requires connection via RS-232 in order to configure functions such as EDID. Ensure that the following items are on hand before proceeding with the installation. · PC or Mac · Terminal software such as PuTTY · USB COM Port Adapter (Not Included) · WyreStorm Part: CAB-USB-3PIN · Latest version of the SW-510-TX API for advanced configuration
not covered in this document.
Note: IP control is only possible when the SW-510-TX and SW-515RX are used as a kit. The web server exists only in the RX.
Basic Wiring Diagram
Personal Computer
In the Box
1x SW-510-TX Transmitter 1x 12V 2A DC Power Supply (US/UK/EU/AU) 1x IR Receiver 2x Mounting Brackets 1x 3-pin Screw Down Phoenix Connector 1x 4-pin Screw Down Phoenix Connector 1x Quickstart Guide (This Document)
USB Mic/Speaker
Deskplate
12V DC 2A Power Supply
SW-515-RX
Laptop
Local Monitor
KEY
HDMI/DisplayPort/USB-C HDBaseT/Ethernet RS-232/Relay Analog Audio Analog Video USB 2.0
Copyright © 2020 WyreStorm Technologies | wyrestorm.com SW-510-TX Quickstart Guide | 200817
1 of 4
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973) support@wyrestorm.com
Wiring and Connections
WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in its entirety before running or terminating any wires to ensure proper operation and to avoid damaging the equipment.
IMPORTANT! Wiring Guidelines · The use of patch panels, wall plates, cable transmitters, kinks in cables,
and electrical or environmental interference will have an adverse effect on signal transmission which may limit performance. Steps should be taken to minimize or remove these factors completely during installation for best results. · WyreStorm recommends using pre-terminated VGA, HDMI, DP and USB cables due to the complexity of these connector types. Using preterminated cables will ensure that these connections are accurate and will not interfere with the performance of the product.
· This product contains a USB-C connection that can be used as an audio/video input. When using this connection verify that the USB-C cable used supports audio/video functionality as not all USB-C cables support this requirement.
Audio Connections
Audio In The audio connections use a 3.5mm (1/8in) TRS Stereo Jack.
Communication Connections
RS-232 Wiring The SW-510-TX uses a 3-pin RS-232 with no hardware flow control. Most control systems and computers are DTE where pin 2 is RX, this can vary from device to device. Refer to the documentation for the connected device for pin functionally to ensure that the correct connections can be made.
PC Connection Connection to a PC uses the RS-232 Control connection and requires the use of a USB to 3-pin Port Adapter cable (CAB-USB-3PIN) in order for a port to be provided on the PC. Note that this adaptor can be used on both v1 and v2 versions.
RS-232 Passthrough
WyreStorm Connector
3rd Party Device
Pin 1 TX (Transmit) ---> To ---> RX (Receive)
Pin 2 RX (Receive) ---> To ---> TX (Transmit)
Pin 3 G (Ground) ---> To ---> G (Ground)
RS-232 Control
WyreStorm Connector
3rd Party Device
Pin 1 12V DC Out No Connection Reserved
Pin 2 TX (Transmit) ---> To ---> RX (Receive)
Pin 3 RX (Receive) ---> To ---> TX (Transmit)
Pin 4 G (Ground) ---> To ---> G (Ground)
Troubleshooting
No or Poor Quality Picture (snow or noisy image) · Verify that power is being supplied to the transmitter and receiving device. · Verify that all HDMI and HDBaseT connections are not loose and are
functioning properly. · Verify that the HDBaseT cable is properly terminated following EIA568B
standard. · Verify that the output resolution of the source and display is supported by
this transmitter. · Configure EDID Settings to a lower resolution. · If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.
No or Intermittent 3rd party Device Control · Verify that the IR, RS-232, and Ethernet cables are properly terminated
following the Wiring and Connections section.
Relays Not Functioning · Verify polarity of the relay connections.
Troubleshotting Tips · WyreStorm recommends using a cable tester or connecting the cable to
other devices to verify functionality.
Copyright © 2020 WyreStorm Technologies | wyrestorm.com SW-510-TX Quickstart Guide | 200817
2 of 4
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973) support@wyrestorm.com
Setup and Configuration
The SW-510-TX is configured using RS-232 commands for Output Resolution, and EDID. Follow these steps to properly configure the transmitter based on the system requirement. Note: The steps and information provided in this QSG are for basic operation of the transmitter out of the box. Refer to the SW-510-TX API for full configuration settings.
Communication Settings
The commands listed below can be sent to the TX through a direct RS-232 connection or via a LAN connection if used as a kit with the SW-515-RX. Each device must be connected together via HDBaseT in to order to send a command from one device to the other. The only exception is Configuring a Static IP Address which requires connection to the RX.
RS-232 Settings
Baud rate:
115200
Data Bits:
8bits
Parity:
None
Stop Bits:
1bit
Flow Control:
None
Configuring Input EDIDs
By default, all inputs are set to an EDID or 1920x1080@60Hz 2CH. However, this can be configured to suit the installation.
Set Input EDID SET EDID [Input] [Resolution] [Device]<CR><LF> Example: SET EDID in1 1 tx<CR><LF> Response: EDID SET in1 1 tx<CR><LF>
Query Input EDID GET EDID [Input] [Device]<CR><LF> Example: GET EDID in1 tx<CR><LF> Response: EDID GET in1 1 tx<CR><LF>
Input= VGA | DP | TXHDMI | USBC | RXHDMI1 | RXHDMI2 Resolution={Below tables based on connection}
VGA EDID
HDMI/USB-C EDIDs
1024x768@60Hz 2CH
1024x768@60Hz 2CH
1280x768@60Hz
1280x720@60Hz
1360x768@60Hz
1360x768@60Hz
1440x900@60Hz
1440x900@60Hz
1600x900@60Hz
1600x900@60Hz
1680x1050@60Hz
1680x1050@60Hz
1920x1080@60Hz
1920x1080@60Hz
1920x1200@60Hz
3840x2160@30Hz
Copyright © 2020 WyreStorm Technologies | wyrestorm.com SW-510-TX Quickstart Guide | 200817
3 of 4
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973) support@wyrestorm.com
Specifications
Audio and Video
Inputs
Outputs
Video Encoding Encoding Data Rate End to End Latency Audio Formats
Video Resolutions (Max)
Supported Standards Maximum Pixel Clock Communication and Control HDMI HDBaseT Ethernet RS-232 IR USB Power Power Supply Max Power Consumption Environmental Operating Temperature Storage Temperature Maximum BTU Dimensions and Weight Rack Units/Wall Box Height With | Without Feet Width With | Without Brackets Depth With | Without Handles Weight Regulatory Safety and Emission
1x VGA In: 15-pin VGA 1x Display Port In: DisplayPort 1.3 1x HDMI In: 19-pin type A 1x Audio In: 3.5mm (1/8in) TRS Stereo 1x Line In: 3.5mm (1/8in) TRS Stereo
1x HDMI Out: 19-pin type A 1x HDBT Out: 8-pin RJ-45 Female
HDBaseT Class C 9.2Gbps
10s (micro seconds) 2ch Analog/PCM | Multichannel: LPCM Video Resolution
1920x1200p @60Hz 8bit 1920x1080p @60Hz 8bit 3840x2160p @30Hz 8bit 4:4:4 4096x2160p @60Hz 8bit 4:2:0 DCI | RGB 297MHz
HDMI 15m/49ft 15m/49ft 7m/23ft 7m/23ft
Cat6 150m/492ft 150m/492ft 100m/328ft 100m/328ft
HDMI | HDCP 2.2 | EDID | DVI/D supported with adapter (not included) HDMI | HDCP 2.2 | EDID | CEC | 2ch audio | USB 2x 8-pin RJ-45 female | Bidirectional over HDBaseT 1x RS-232 (Control): 3-pin Phoenix | 1x RS-232 (Passthrough): 3-pin Phoenix 1x IR RX: 3.5mm (1/8in) TS Mono 1x USB-C: USB 3.1 Audio/Video | 2x USB Host: USB-B | 3x USB Device: USB-A USB over HDBT limited to 190Mbps | Max 5v 500mA per Type A port
12V DC 2A 14.02W
0 to + 45°C (32 to + 113 °F), 10% to 90%, non-condensing -20 to +70°C (-4 to + 158 °F), 10% to 90%, non-condensing 56.3BTU/hr
<1U 44.5mm/1.76in | 42mm/1.66in 263mm/10.36in | 220mm/8.67in 148.7mm/5.86in | 148.7mm/5.86in 0.97kg/2.13lbs
CE | FCC | RoHS
Cat6a/7 150m/492ft 150m/492ft 100m/328ft 100m/328ft
Note: WyreStorm reserves the right to change product specification, appearance or dimensions of this product at any time without prior notice.
Warranty Information WyreStorm Technologies LLC warrants that its products to be free from defects in material and workmanship under normal use for a period of five (5) years from the date of purchase. Refer to the Product Warranty page on wyrestorm.com for more details on our limited product warranty.
Copyright © 2020 WyreStorm Technologies | wyrestorm.com SW-510-TX Quickstart Guide | 200817
4 of 4
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973) support@wyrestorm.com