Viavito | Premium Sports & Fitness Products
Login • Instagram
Owner's Manual for VIAVITO models including: FT500, Football Table, FT500 Football Table, Table
Viavito FT500 Football Table – Sweatband
File Info : application/pdf, 22 Pages, 2.62MB
DocumentDocumentOwner's Manual. FT500 Football Table www.viavito.com Manual version 1.2 Congratulations on purchasing your very own FT500 Football Table. You have chosen a high-quality, safe and innovative product, and we are certain it will keep you entertained for hours. Please take the time to read this owner's manual as it will help you to get the most out of your new product. For more information, or if you require any assistance please email us at support@viavito.com Manual Contents. Safety Information Assembly Contents Checklist Assembly Instructions 03 04/09 04/05 06/17 Table Maintenance and Care Customer Support Contact Information Manufacturer's Warranty Technical Information Parts List Exploded Diagram 18 19/20 19 20 21/22 21 22 02 www.viavito.com Safety Information. · Please read all the instructions carefully before using this product. · Retain this manual for future reference. · The specifications of this product may vary slightly from the illustrations and are subject to change without notice. IMPORTANT SAFETY NOTICE: note the following precautions before using the product. 01 Assemble the product exactly as per the instructions in this manual. We recommend that two adults work together to assemble this table. 02 Check all the screws, nuts and other connections before using the table for the first time and ensure that it has been built correctly and is safe to be used. 03 Set up the table in a dry, level place and keep it away from moisture and water. 04 DO NOT use cleaning products such as detergents. To clean the table only use a clean cloth. 05 This product is for home use only. 06 This is not a toy and is intended for use by or under the supervision of adults. 07 Choking hazard! Keep small parts and polybags away from children during and after assembly. 08 Do not place anything on the top of the playfield. 09 Please keep in mind that player rods are constantly moving in and out during play. To maintain personal safety and avoid injury, do not get too close to the table when pushing and pulling the rods to reposition your players. SAFETY STANDARDS www.viavito.com 03 Assembly. Contents Checklist Before you begin the assembly, remove all of the contents from the box and make sure that you have all the parts listed and in correct quantities. This will ensure the quickest and most organized assembly. Please Note: To assemble the table you will need a Phillips-head screwdriver (not included). An electric screwdriver can be used in the assembly. Set it to a very low torque and use with extreme caution to prevent damage to the product. #1 #2 #3 #4 x1 Assembly Frame x1 Support Brace x2 Leg Panel x2 Leg Type A #5 #6 #7 #8 x2 Leg Type B x2 Support Strut x2 Metal Plate with Ring x4 Metal Plate #9 #10 #11 #12 x4 Leg Leveler x4 Stop Ring x16 Rod Bumpers x16 Plastic Rod Washer #13 #14 #15 #16 x11 Players x8 Rod Handle x8 Rod End Cap x2 Ball Entry Cup 04 www.viavito.com #17 #18 #19 #20 x2 Soccer Ball (Black/ White) #21 #22 Scorer x2 x2 x2 3-Man Rod 2-Man Rod #23 #24 x2 5-Man Rod x26 M4X28mm Bolt #25 #26 #27 x26 M4 Nut x12 1/4" *1-3/4" Bolt #28 x14 1/4" *1-3/8" Bolt x40 1/4" Washer x12 5/16" *1-3/8" Bolt x12 5/16" Washer #29 #30 #31 #32 #33 1/4" Nut x14 x4 F3.5X45mm Screw #34 x6 T3.5mmx12mm Screw NOT INCLUDED x1 Allen Wrench x1 Allen Key x2 Soccer Ball (White) Screwdriver www.viavito.com 05 Assembly Instructions Find a clean and level surface to begin the assembly of your football table. The table will be partially assembled upside down and then turned over onto its legs. Turning over the table will require at least two strong adults. Your table comes mostly pre-assembled. Follow these easy steps to quickly and safely put the table together and get it ready to start playing. Estimated setup time is 30 minutes. Step One. 01 Attach (#7) Metal Plates with Ring to the (#2) Support Brace using four (#25) Bolts with #26 Washers. 02 Fasten the support brace and metal plates using (#26) Washers and (#29) Nuts. Parts #2 x1 Support Brace #7 x2 Metal Plate with Ring #25 x8 1/4" *1-3/8" Bolt #26 x8 1/4" Washer #29 x4 1/4" Nut Tools #33 x1 Allen Key #32 x2 Allen Wrench 06 www.viavito.com Step Two. 01 Position the (#2) Support Brace with fixed metal rings in the center of the playfield and align with pre-drilled holes in the cabinet's side panels. 02 Attach using (#24) Bolts with (#26) Washers. Parts #1 x1 Assembly Frame #2 x1 Support Brace with Metal Rings from Step 1 #24 x4 1/4" *1-3/4" Bolt #26 x4 1/4" Washer Tools #33 x1 Allen Key www.viavito.com 07 Step Three. 01 Secure (#4) Leg Type A and (#5) Leg Type B to the table as shown on the drawing below using (#27) Bolts and (#28) Washers. 08 Parts #4 x1 Leg Type A #5 x2 Leg Type B #27 x12 5/16" *1-3/8" Bolt #28 x12 5/16" Washer Tools #33 x1 Allen Key www.viavito.com Step Four. 01 Attach (#8) Metal Plates to the (#3) Leg Panel using four (#25) Bolts with (#26) Washers. Fasten the leg panels and metal plates using (#26) Washers and (#29) Nuts. 02 Repeat above steps for the second leg panel. Parts #3 x2 Leg Panel #8 x4 Metal plate #25 x8 1/4" *1-3/8" Bolt #26 x16 1/4" Washer Tools #33 x1 Allen Key www.viavito.com 09 Step Five. 01 Connect Left and Right legs using the panels assembled in the previous step using (#24) Bolts and (#26) Washers. Parts #3 x2 Leg Panel with metal plates from Step 4 #24 x8 1/4" *1-3/4" Bolt #26 x8 1/4" Washer Tools #33 x1 Allen Key 10 www.viavito.com Step Six. 01 Using (#25) Bolt with (#26) Washer attach (#6) Support Strut to the metal plate of the leg panel. Tighten the bolts using another (#26) Washer and (#29) Nut on the other side of the panel. 02 Hook the other end of the (#6) Support Strut into the metal ring of the support brace. 03 Repeat as above for the second support strut. 04 Attach one (#9) Leg Leveller to the bottom of each leg. Parts #6 x2 Support Strut #25 x2 1/4" *1-3/8" Bolt #26 x4 1/4" Washer #29 x2 1/4" Nut Tools #9 #33 x4 Leg Leveler x1 Allen Key www.viavito.com 11 Step Seven. 01 Turn the football table over. CAUTION! 1: It is recommended that two adults turn the table over. 2: Take hold of the table as shown. 3: Turn the table over. 4: Place the table on all four feet at the same time. Take hold of the table. DO NOT hold the table by the legs. DO NOT lean the table on its legs. 12 www.viavito.com Parts #19 x4 3-Man Rod #20 x2 2-Man Rod #21 x2 5-Man Rod #10 x4 Stop Ring #12 x16 Plastic Rod Washer #11 Step Eight. Each side has four player rods to be set in a 1-2-5-3 formation. The correct layout starting at either end is: 1 home player 2 home players 3 away players 5 home players 5 away players 3 home players 2 away players 1 away player Goalkeeper Setup Start by setting up a goalkeeper at either end of the table. 01 Take (#19) 3-Man Rod and insert it into the corresponding hole in the side panel. Thread the rod through just one hole and not all the way through the cabinet! 02 Slide onto the rod, one by one, (#11) Rod Bumper, (#12) Plastic Rod Washer, first (#10) Stop Ring, one (#13) Player (ensure your goalie is facing the right direction!) and then second (#10) Stop Ring, second (#12) Plastic Rod Washer and second (#11) Rod Bumper. 03 Align Stop Rings and Player with pre-drilled holes in the rod and screw them in place using (#22) Bolts and (#23) M4 Nuts. Now insert the rod through the hole on the opposite side of the table. x16 Rod Bumper #13 #22 #23 Tools NOT INCLUDED Player 2x11 x26 M4X28mm Bolt x26 M4 Nuts Screwdriver www.viavito.com 13 Assembly of Team Players Note: Ensure that all team players are facing the same direction as their goalkeeper! 01 Insert Rods number 20, 21 and 19 into the second, fourth and sixth holes respectively. 02 Slide onto each rod, one by one, (#11) Rod Bumper, (#12) Plastic Rod Washer and appropriate number of Black or Grey team players (item #13). Align players with predrilled holes in the rod and insert #22 Bolts into the front of each player. Secure on the back using (#23) M4 Nuts. 03 Finish the assembly of each rod by sliding on second (#12) Plastic Rod Washer and (#11) Rod Bumper. Once complete thread the rod through the hole on the opposite side. Repeat the above steps for remaining rods. 14 www.viavito.com #11 Rod Bumper #12 Plastic Rod Washer #10 Stop Ring #19 Rod #21 Rod #20 Rod #19 Rod #19 Rod #20 Rod #21 Rod #19 Rod #10 Stop Ring #12 Plastic Rod Washer #11 Rod Bumper www.viavito.com 15 Step Nine. 01 Push (#14) Rod Handles onto the player rods and add (#15) End Caps at the opposite end. 02 Insert (#16) Ball Entry Cup into the center hole of each side of the table. Secure it by screwing (#31) Screws. T3.5mmx12mm Screw Parts #14 x8 Rod Handles #15 x8 End Cap #16 x2 Ball Entry Cup #31 x2 T3.5mmx12mm Screw Tools NOT INCLUDED Screwdriver 16 www.viavito.com Step Ten. 01 Screw (#18) Slide Scorers into the pre-drilled holes above each goal using (#30) Screws. Parts #18 x2 Slide Scorers #30 x4 F3.5X45mm Screw Tools NOT INCLUDED Screwdriver www.viavito.com 17 Maintenance and Care. 01 We recommend that you keep the table covered when not in use. This will prevent dust from building up and will prolong the life of your football table. If it does get dusty, use a clean, dry cloth to remove any of the loose dirt from the table. Do not use any cleaning products. 02 This table is designed for indoor use only. Damage can occur if the table is exposed to water, dampness, high humidity, extreme temperatures, etc. 03 Do not sit, climb or lean on the table or the rods. 04 Periodically check all screws and bolts to make sure that they are secure and in good working condition. If loose, tighten with a Phillips-head screwdriver. 05 Do not drag the table when moving it as this will damage the legs. Do not lift the table by the rods. When moving the table, lift the table off its legs and place it down on all four feet at the same time. 18 www.viavito.com Customer Support. Contact Information Should you require any assistance regarding this product please gather the following information and then contact us using the details below: · Original purchase date · Place of purchase · Information about the place and conditions of use · Precise description of the issue or defect. The best way to contact us is via the website: www.viavito.com Viavito Ltd Unit A, Park 40 Flanshaw Way Wakefield WF2 9LP Email: support@viavito.com IMPORTANT!! - Please retain your sales receipt. Viavito Customer Care may request proof of purchase to validate eligibility for warranty service. Warranty cover starts from the date shown on the proof of purchase. The best way to contac us is via the website: www.viavito.com https://www.facebook.com/MyViavito https://instagram.com/Viavito https://twitter.com/MyViavito www.viavito.com 19 Manufacturer's Warranty Viavito ltd warrants this product to be free of defects of material and workmanship, under normal use and conditions, for a period of 6 months from the date of the original purchase. Terms. This warranty extends only to the original purchaser and is not transferable. The warranty does not cover: 01 Normal wear and tear 02 Any changes to upgrade this product from its normal state or use other than as described in the user manual 03 Damage resulting from: a) Transport b) Abuse, misuse, failure to follow instructions or improper or abnormal use c) Non-home use - including commercial, professional, or rental purposes d) Repairs not provided by Viavito ltd e) Accidents, lightning, water, fire, or any other causes beyond the control of Viavito f) Improper location including, but notlimited to, garden sheds,garages,humid, damp, cold, hot, dusty,or outdoor environments, or nearwater such as swimming pools etc. Viavito is not responsible or liable for direct, indirect, or consequential losses arising out of or in connection with the use of this product or damages with respect to any loss of property, revenue, profits, enjoyment or use, nor for any costs of removal or installation of this product. In the event of the table requiring a repair, this may need to be performed at a Viavito authorised repair centre. This warranty covers products purchased as new inside the United Kingdom. This warranty is in addition to and does not in any way affect your statutory rights 20 www.viavito.com Technical Information. Parts List . PART # 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 PART NAME Assembly Frame Support Brace Leg Panel Leg Type A Leg Type B Support Strut Metal Plate with Ring Metal Plate Leg Level Stop Ring Rod Bumpers Plastic Rod Washer Player Rod Handle Rod End Cap Ball Entry Cup Soccer Ball (Black/ White) Scorer 3-Man Rod 2-Man Rod 5-Man Rod M4X28mm Bolt M4 Nut 1/4" * 1-3/4" Bolt 1/4" * 1-3/8" Bolt 1/4" Washer 5/16" * 1-3/8" Bolt 5/16" Washer 1/4" Nut F3.5X45mm Screw T3.5X12mm Screw Allen Wrench Allen Key Soccer Ball (White) www.viavito.com QTY 1 1 2 2 2 2 2 4 4 4 16 16 11+11 8 8 2 2 2 4 2 2 26 26 12 14 40 12 12 14 4 6 1 1 2 1271 Exploded Diagram 22 www.viavito.com