Scanning this bar code will enable the scanner to enter manual trigger mode. 013300 Trigger Mode Continuous Mode This mode enables the engine to scan/capture, decode and transmit over and over again. ... And EAN-8/EAN-13 Barcode can be augmented with a two-digit or five-digit add-on code form a new one.
3) Make sure the device has Bluetooth “On”.Scan for devices. 4) In the list of found devices, select “NetumBluetooth”.Tap Pair. 5) The scanner will connect to the Android device. 6) The scanner will beep once after it has connected and is ready to scan barcodes 3. Pairing with your IOS device 1) Power on the scanner. Make sure the ...
Pairing with your IOS device 1) Power on the scanner. Make sure the scanner is discoverable (unpaired). A few seconds later the blue indicator will keep flashing. 2) Click on “Bluetooth”in the left column. Your IOS device will automatically start searching for any Bluetooth Devices in the area.
NT-1228BC
Quick Setup Guide
This model can work both via USB cable or via bluetooth.
V18.9.7
Connection Mode Working via USB cable Get Started: Connect scanner with your device via USB cable. If you use US keyboard, it's a plug and play model. If you use other type of keyboard , please refer to below "keyboard language" to configure the keyboard language before use it. Working via Bluetooth Get Started: US Keyboard is configured by default. After you pair the bluetooth with your device, you can start to use it. If you use other type of keyboard ,please configure the keyboard language before you use it. Low voltage Alarm: Scanner will make 2x beeps to remind you that it's under low voltage. Plug the USB cable to charge power for it. Firmware Version: Read below command barcode to check scanner firmware version.
Check Scanner Version
Below programming barcodes are applied for version NT_ZNCWBSDk8815
Barcode Programming Netum barcode scanners are factory programmed for the most common terminal and communications settings. If you need to change these settings, programming is accomplished by scanning the bar codes in this guide. An asterisk (*) next to an option indicates the default setting.
Bluetooth Connection
1. Pairing with windows XP or Windows 7/8/10
1) Power on the scanner , a few seconds later the blue indicator will keep flashing. 2) Enter the `Control Panel' - `Devices and Printers' - `Add a device' select, `Bluetooth' to
add the device to your computer 3) Click `Next', the scanner will beep to indicate a successful pairing, and the light will turn to solid blue.
2. Android: Connect Android Device in Basic Mode
1) Power on the scanner. Make sure the scanner is discoverable (unpaired). A few seconds later the blue indicator will keep flashing.
2) Touch Home | Menu | Settings | Wireless & Networks | Bluetooth settings 3) Make sure the device has Bluetooth "On". Scan for devices. 4) In the list of found devices, select "Netum Bluetooth". Tap Pair. 5) The scanner will connect to the Android device. 6) The scanner will beep once after it has connected and is ready to scan barcodes
3. Pairing with your IOS device
1) Power on the scanner. Make sure the scanner is discoverable (unpaired). A few seconds later the blue indicator will keep flashing.
2) Click on "Bluetooth" in the left column. Your IOS device will automatically start searching for any Bluetooth Devices in the area.
3) Once you have identified the "Netum Bluetooth" on the screen, tap on it and you will automatically be connected. The scanner's LED light will turn to solid blue.
Operation mode A) BT HID Mode (Default)* No Software installation needed, connects to most devices with bluetooth or USB interface. In this mode, the scanner interacts with the device like a keyboard. Therefore, the scanner will work with Safari, Notes, and any other applications that supports an active cursor.
BT HID Mode
Note: this command barcode is only apply for Bluetooth Wireless Mode
Keyboard Language
In order to let scanner upload the codes in a correct way, you have to configure the keyboard language before you use it. For example If you use French Keyboard, just scan barcode of "French Keyboard", after that scanner will upload barcodes according to French keyboard layout. American Keyboard is set by default, if you use a US keyboard you can just skip this part.
American Keyboard *
Portugal Keyboard
French Keyboard
Spanish Keyboard
Germany Keyboard
Turkey Q Keyboard
Italy Keyboard
Turkey F Keyboard
B) Application Mode (SPP)
For Android or Windows only Software installation is required, If you have an application that supports mobile scanners this is the mode recommended.
BT SPP Mode Note: this command is only apply for Bluetooth Wireless Mode
Scan Mode Trigger Mode (Default) Scanning this bar code will enable the scanner to enter manual trigger mode.
013300 Trigger Mode
Continuous Mode
This mode enables the engine to scan/capture, decode and transmit over and over again.
Auto Sense Mode
013304 Continuous Mode
Scanning this bar code will enable the scanner to enter auto sense mode.
02311 Auto Sense On
02310 Auto Sense Off
Data Uploading Mode If you are heading for a working area which lies outside the signal range, you may activate the offline mode of the scanner, following the steps described below. Under this enhanced offline mode, all scanned data will be stored directly into the buffer memory of the device. Furthermore, the data entries will be permanently saved in the buffer memory prior to the manual upload into the working station, so that you may upload them time and again to your liking. 1). By scanning the following barcode, the offline mode will be activated
Offline Mode 2). By scanning the following barcode, all data in the buffer memory will be deleted
Clear All Memory 3).By scanning the following barcode, all data entries in the buffer memory can be manually uploaded after reconnecting to the working station (only in offline mode).
Uploading the Data 4). By scanning the following barcode, the gross quantity of the uploaded data entries will be summarised (only in offline mode).
Summarising of uploaded data entry quantity 5). By scanning the following barcode, the device leaves the offline mode, instant uploading mode will be activated. (By default)
Instant uploading mode Notes: Command barcodes from Working mode section are only applied for Bluetooth wireless mode,
Terminator The scanner provides a shortcut for setting the terminating character suffix to CR or CRLF and enabling it by scanning the appropriate barcode below.
0212@\r CR*
0212@\n LF*
0213@\r\n CR+LF
0210@ NONE
Idle Time
Scanner will stay awake during the idle time that you configure for it and it will turn to sleep if you haven't used it during the whole idle time.
30 s
6 Mins
12 Mins
30 Mins
1Hour
2Hours
IOS Keyboard POP UP/HIDE During the scanning IOS keyboard can be hided or popped up by scanning below command barcode.
IOS Keyboard POP UP/HIDE
Beeper Enable/Disable scanner to beep to indicate successful scan.
BEEP ON
BEEP OFF
Restore factory default Scanning the following barcodes one by one to restore the scanner to factory defaults. (Four steps included) 1. Factory Restore
2. Serial Port
3. Baud Rate 19200
4. Enter+LF
Transmit Code ID Character A code ID character identifies the code type of a scanned bar code. This can be useful when decoding more than one code type. The code ID character is inserted between the prefix character (if selected) and the decoded symbol. (Refer to Appendix A)
01400 Disable Code ID*
01401 Enabled Code ID Prefix
01402 Enabled Code ID Prefix
Common barcode Function Enable/Disable EAN-8 To enable or disable EAN-8, scan the appropriate bar code below.
00371 Enable EAN-8*
00370 Disable EAN-8
00571 EAN-8 Transit Check Digit*
00570 EAN-8 Do Not Transit Check Digit Enable/Disable EAN-13 To enable or disable EAN-13, scan the appropriate bar code below.
00361 Enable EAN-13*
00360 Disable EAN-13
00461 EAN-13 Transit Check Digit *
00460 EAN-13 Do Not Transit Check Digit Add-On Code And EAN-8/EAN-13 Barcode can be augmented with a two-digit or five-digit add-on code form a new one. In the example below, the part surrounded by blue line is an EAN-8 barcode while the part circled by red line is add-on code. " Disable Add-on Code" is configured by default.
EAN /UPC Add-On 2 or 5 To enable or disable EAN/UPC add on 2 or 5 digts scan the appropriate barcode below.
00551 Enable add-on 2 digits
00552 Enable add-on 5 digits
00553 Enable add -on 2 or 5 digits
00550 Disable add-on 2 or 5 digits Enable/Disable Convert EAN-13 to ISBN To enable or disable convert EAN-13 to ISBN, scan the appropriate barcode below.
00481 Enable EAN-13 Transfer to ISBN
00480 Disable EAN-13 Transfer to ISBN*
Enable/Disable Convert EAN-13 to ISSN To enable or disable convert EAN-13 to ISSN, scan the appropriate barcode below.
01501 Enable EAN-13 Transfer to ISSN
01500 Disable EAN-13 Transfer to ISSN* Enable/Disable Codabar To enable or disable codabar, scan the appropriate barcode below.
00851
Enable Codabar*
00850 Disable Codabar Enable/Disable Code 11 To enable or disable Code 11, scan the appropriate bar code below.
01261 Enable Code 11*
01260 Disable Code 11 Enable/Disable Code 39 To enable or disable Code 39, scan the appropriate bar code below.
00221 Enable Code 39*
00220 Disable Code 39 Enable/Disable Code 39 Full ASCII Code 39 Full ASCII is a variant of Code 39 which pairs characters to encode the full ASCII character set.
00231 Enable Full ASCII*
00230 Disable Full ASCII Enable/Disable Code 93 To enable or disable Code 93, scan the appropriate bar code below.
00621 Enable Code 93*
00620 Disable Code 93 Enable/Disable Code 128 To enable or disable Code 93, scan the appropriate bar code below.
00691 Enable Code 128*
00690 Disable Code 128 Enable/Disable Code 32 To enable or disable Code 93, scan the appropriate bar code below.
01950 Disable Code 32*
01951 Enable Code 32 Enable/Disable GS1 DataBar Limited (RSS Limited) To enable or disable GS1 DataBar Limited, scan the appropriate bar code below.
01771 Enable RSS Limited
01770 Disable RSS Limited GS1 DataBar Ominidirectional ( RSS Ominidirectional ) To enable or disable GS1 DataBar Ominidirectional, scan the appropriate bar code below.
01761 Enable RSS Ominidirectional
01760 Disable RSS Ominidirectional Enable/Disable UPC-A To enable or disable UPC-A, scan the appropriate bar code below.
00341 Enable UPC-A*
00340 Disable UPC-A
00241 Enable Transit Check Digit *
00240 Disable Transit Check Digit Enable/Disable Convert UPC-A to EAN-13 To enable or disable Convert UPC-A to EAN-13, scan the appropriate bar code below.
00391 Enabled UPC-A to EAN-13
00390 Disable UPC-A to EAN-13 Enable/Disable UPC-E To enable or disable UPC-E, scan the appropriate bar code below.
00351 Enable UPC-E
00350 Disable UPC-E
Enable/Disable Convert UPC-E to UPC-A To enable or disable Convert UPC-E to UPC-A, scan the appropriate bar code below.
00381 Enable Convert UPC-E to UPC-A
00380 Disable Convert UPC-E to UPC-A Enable/Disable Interleaved 2 of 5 To enable or disable Interleaved 2 of 5, scan the appropriate bar code below.
00961 Enabled Interleaved 2 of 5
00960 Disabled Interleaved 2 of 5 Enable/Disable Industrial 2 of 5 To enable or disable Industrial 2 of 5, scan the appropriate bar code below.
01061 Enable Industrial 2 of 5
01060 Disable Industrial 2 of 5 Enable/Disable Standard 2 of 5 To enable or disable Standard 2 of 5, scan the appropriate bar code below.
01871 Enable Standard 2 of 5
01870 Disable Standard 2 of 5 Enable/Disable Matrix 2 of 5 To enable or disable Matrix 2 of 5, scan the appropriate bar code below.
01461 Enable Matrix 2 of 5 Enable/Diable MSI To enable or disable MSI, scan the appropriate bar code below.
01151 Enable MSI
01150 Disable MSI
Enable /Disable Plessey To enable or disable Plessey, scan the appropriate bar code below.
01161 Enable Plessey
01160 Disable Plessey
Hide Prefix or suffix digits The start/middle/end of barcode chars can be hidden. After scan below hide set barcode, scan a double-digit hexadecimal number that you want to hide char length(00~FF e.g. hide length 4, scan 0, 4).
Hide Barcode Start Chars
Hide Barcode Middle Chars
Hide Barcode Middle Char Start
Hide Barcode End Chars
Output Format To change the Scan Data Transmission Format, scan one of the eight bar codes corresponding to the desired format.
Enable Hide Barcode Start Char
Enable Hide Barcode Middle Char
Enable Hide Barcode End Char
To Hide chars of barcode Start/Middle/End: Procedures 1. Scan the Hide Barcode Start / Middle Start / Middle length / End Chars symbol. 2. Determine the hex value for the length you wish to enter(hide 4 chars, scan 0,4; hide 12 chars, scan 0,C). 3. Scan the 2 digit hex value from the Numeric Bar Codes 4. Scan the output format to enable or cancel hide char function.
Custom prefix and suffix Maximum 20 prefixes and 20 suffixes can be added to scan data for use in data editing. To set these values, scan a double-digit hexadecimal number (i.e. two bar codes) that corresponds to ASCII values. See the Table 1 and Numeric Bar Codes in appendix. To Add a Prefix or Suffix: 1. Scan command barcode of " Add Prefix" or" Add Suffix ". 2. Check the prefix or suffix hex value from the ASCII Chart. 3. Scan the 2 digit hex value from the Numeric Bar Codes 4. Repeat Steps 2 and 3 for all the prefix or suffix that you want to add. 5. Scan the output format to enable or disable prefix/suffix output.
Add Prefix
Clear All Prefix Numeric Bar Codes
Add Suffix Clear All Suffix
Output Format To change the Scan Data Transmission Format, scan one of the eight bar codes corresponding to the desired format.
*Default output format Enable Prefix output
Enable Suffix output
Example on how to add normal prefix or suffix on barcode "123456789" Add " A" and "B" as prefixes and "!" as suffix 1. Scan command barcode of " Add Prefix"
2. Check the prefix hex value from the ASCII Chart. A- "4","1"; B-"4" "2"; 3. Scan the 2 digit hex value from the Numeric Bar Codes
4. Scan the output format to enable prefix output. Enable Prefix output
5. Scan command barcode of " Add Suffix" to add "!" as suffix. Add Suffix
6. Check the suffix hex value from the ASCII Chart. !- "2" "1" 7. Scan the 2 digit hex value from the Numeric Bar Codes.
8. Scan the output format to enable suffix output. Enable Suffix output
9. Scan the barcode then you will get AB123456789!
Example on how to add Combination Key suffix for barcode "123456789" Add "Ctrl+P" on "123456789" as suffix 1.Scan command barcode of " Add Suffix" to add "Ctrl+P" as suffix.
Add Suffix 2. Check the suffix hex value from the ASCII Chart. Ctrl+P - "9" "7" "5" "0" 3. Scan the 4 digits hex value from the Numeric Bar Codes.
4. Scan the output format to enable suffix output. Enable Suffix output
5. Scan " Keyboard Ctrl Combination Key"
6. Scan the barcode 123456789. (test it on Excel)
Table 1. ASCII Character Equivalents
HEX
ASCII
HEX
ASCII
20H
Space
30H
0
21H
!
31H
1
22H
"
32H
2
23H
#
33H
3
24H
$
34H
4
25H
%
35H
5
26H
&
36H
6
27H
'
37H
7
28H
(
38H
8
29H
)
39H
9
2AH
*
3AH
:
2BH
+
3BH
;
2CH
,
3CH
<
2DH
-
3DH
=
2EH
.
3EH
>
2FH
/
3FH
?
60H
`
70H
p
61H
a
71H
q
62H
b
72H
r
63H
c
73H
s
64H
d
74H
t
65H
e
75H
u
66H
f
76H
v
67H
g
77H
w
68H
h
78H
x
69H
i
79H
y
6AH
J
7AH
z
6BH
k
7BH
{
6CH
l
7CH
6DH
m
7DH
}
6EH
n
7EH
~
6FH
o
7FH
DEL
HEX
ASCII
HEX
ASCII
40H
@
50H
P
41H
A
51H
Q
42H
B
52H
R
43H
C
53H
S
44H
D
54H
T
45H
E
55H
U
46H
F
56H
V
47H
G
57H
W
48H
H
58H
X
49H
I
59H
Y
4AH
J
5AH
Z
4BH
K
5BH
[
4CH
L
5CH
\
4DH
M
5DH
]
4EH
N
5EH
^
4FH
O
5FH
_
80H
F1
90H
End
81H
F2
91H
Page Down
82H
F3
92H
Right Arrow
83H
F4
93H
Left Arrow
84H
F5
94H
Down Arrow
85H
F6
95H
Up Arrow
86H
F7
96H
Print Screen
87H
F8
97H
*Ctrl
88H
F9
98H
*Shirt
89H
F10
99H
*Left Alt
8AH
F11
9AH
*Right Alt
8BH
F12
08H
BS
8CH
Insert
09H
HT
8DH
Home
0AH
LF
8EH
Page Up
0DH
CR
8FH
Delete
1BH
ESC
Table 2. Code ID
No
Code ID
1
@
2
A
3
C
4
D
5
E
6
F
7
I
8
J
9
K
10
M
11
N
12
O
13
P
14
Q
15
S
16
T
17
U
18
V
Code (Barcode Type) 00 01 03 04 05 06 09 0A 0B 0D 0E 0F 10 11 13 14 15 16
Barcode Type ALL TYPES CODE 128 EAN 8 EAN 13 UPC-A UPC-E CODE 93 GS1 Omnidirectional GS1 Limited CODE 39 Interleaved 2 of 5 Industrial 2 of 5 Standard 2 of 5 Matrix 2 of 5 MSI Plessey CODE 11 Codebar
Support
For any inquiries concerning our products, please send an email to service@gzxlscan.com, and we will respond to you as soon as possible.
Contact Information
Tel.:+0086 20-6626-0708 Email:service@gzxlscan.com Skype: service@gzxlscan.com Addr.:Unit 137, The Pacific Industry Park, Xintang Town,Zengcheng District, Guangzhou,China/511340 Made in China
Microsoft Office Word 2007 Microsoft Office Word 2007