HEADRUSH HRB 5036 True Wireless Earbuds

Introduction

Thank you for purchasing the HRB 5036 true wireless earbuds. In order to maximize your listening experience, please read the following instructions.

Operating Instructions

Prior to first use, remove the plastic battery isolator tab located between the earbuds and the charging case.

Key Components:

• 1 MFB (Multi-function button): Located on each earbud.
• Earbuds LED indicator/microphone: Indicates status and houses the microphone.
• Charging case LED indicator: Shows the charge level of the case.
• USB-C charging port: For charging the case.

Basic Operations:

EQ modes available: Standard mode, Movie mode (more bass), Gaming mode (more treble). The EQ level returns to standard mode every time the earbuds are turned off or returned to the charging case.

Function compatibility may vary among different smartphones or devices. Not all functions are available on all devices.

What's Included

• HRB 5036 earbuds
• Charging case
• USB-C charging cable
• Instruction manual
• Additional large and small earbud tips included (medium tips installed on earbuds).

Charging the Case

Use the included charging cable to fully charge the case before first use. It takes approximately 2.5 hours to fully charge.

LED Indicators for Case Charging:

• Blue LEDs flash while the case is charging.
• The 4 blue LEDs will turn ON after the case has charged and then turn OFF.

Case Charge Level Indicators:

• 1 LED: 25%
• 2 LEDs: 50%
• 3 LEDs: 75%
• 4 LEDs: 100%

Charging the Earbuds

The earbuds automatically power OFF and begin charging when placed in the charging case. The white LED turns ON to indicate charging and OFF when complete. It takes approximately 1.5 hours to fully charge the earbuds.

A fully charged case provides up to 3 charges for the earbuds.

During use, a white LED will flash twice and the earbuds will beep once to indicate low battery. Please charge the earbuds.

When earbuds are in the case, fully charged, and the lid is opened, the earbud LEDs light for about 10 seconds then turn OFF.

Pairing

The earbuds automatically enter Bluetooth pairing mode when used for the first time. The left and right earbuds connect to each other automatically.

1. Remove both earbuds from the charging case. The blue LED flashes 3 times to indicate power ON. Both earbuds flash blue/white to indicate pairing. When one earbud's LED flashes blue and white and the other turns OFF, they have connected successfully to each other.
2. Select "HRB 5036" from your device's Bluetooth list to pair.
3. The white LEDs on both earbuds will be ON for about 4 seconds, then turn OFF. The earbuds will beep twice to indicate successful connection to the device.
4. After initial pairing, the earbuds automatically connect to your device when turned ON, provided Bluetooth is ON and the device is within range.

To Use Only the Left or Right Earbud

If both earbuds are ON and paired, you can return one earbud to the charging case; the other will continue playing. To use a single earbud, remove it from the charging case; it will turn ON and connect automatically.

Clear Paired Memory

If earbuds do not connect to each other, reset them and clear paired memory.

1. Remove "HRB 5036" from your device and turn Bluetooth OFF.
2. When white and blue LEDs are ON, press each MFB button 5 times until both LEDs flash 4 times.
3. One earbud stops flashing while the other flashes white/blue to complete the process.
4. Turn Bluetooth back ON in your device settings and select "HRB 5036".

Operation Summary

• Music Playback: Touch either MFB button twice to pause/resume.
• Next Song: Touch and hold the right MFB button.
• Previous Song: Touch and hold the left MFB button.
• Calls: Music pauses and earbuds ring for incoming calls. Touch either MFB button twice to answer, touch and hold for one second to reject.
• Power OFF: Touch and hold either MFB button for 5 seconds.
• EQ Modes: Touch either MFB button 4 times to cycle through Standard, Movie (more bass), and Gaming (more treble) modes, with a beep for each change.

Earbuds automatically power OFF if no Bluetooth device is paired after approximately 4 minutes.

Warnings

• Supervise children when using equipment; this product is not a toy.
• Listening at high volume levels for extended periods may damage hearing.
• Consult a physician before use if you have a pacemaker or other electrical medical devices.
• Clicks from switching sources or plugging in earbuds at high volume may affect hearing. Set volume to minimum before such actions.
• DO NOT use earbuds while driving or cycling.
• Small parts included can be a choking hazard; keep away from children under 3.
• If not used for long periods, charge earbuds and case at least every 3 months.
• Dispose of rechargeable batteries properly; DO NOT dispose of in fire to prevent an explosion.

Improving the Sound

Sound may be improved by switching to a different eartip size. Ensure eartips fit comfortably.

Cleaning

Remove eartips from earbuds and wash them with mild detergent and water. Ensure tips are dry before reattaching.

Important Safety Information & Cautions

• Keep in a safe place free from dust, liquid, and extreme temperatures.
• DO NOT attempt to disassemble the product.
• DO NOT use chemicals to clean the product.

Specifications

Earbuds

* A2DP-Advanced Audio Distribution Profile, AVRCP-Audio Video Remote Control Profile, HSP-Handset Profile, HFP-Handsfree Profile.

** Approximate playback time; battery life depends on individual use and may be more or less than specified.

Charging Case

Troubleshooting

No sound

Check the volume on your audio device to ensure it is outputting sound.

Connection Problems

• Return earbuds to the case and remove them again if connection issues occur.
• Refer to the "Clear Paired Memory" section for resetting.

Earbuds not fitting comfortably

Switch to a different eartip size to find the appropriate fit.

Regulatory Compliance

Bluetooth®

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth® SIG, Inc. Use by The Source (Bell) Electronics Inc. is under license. Other trademarks and trade names are those of their respective owners.

FCC Regulatory Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Compliance: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

ISED Regulatory Compliance

This device contains licence-exempt transmitters that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.

CAN ICES-003(B)/NMB-003(B).

The Source - Warranty

The Source warrants this product to be free from defects in materials and workmanship for twelve (12) months from the date of purchase. During this period, bring the product and proof of purchase to any The Source store or participating dealer for replacement (where available) without charge. Misused or accidentally damaged products are excluded.

This warranty applies only to products purchased through The Source company-owned stores or participating dealers in Canada. It does not confer any legal rights beyond those stated, but you may have additional statutory rights that vary by country, state, province, or governmental entity where The Source operates. This warranty is subject to all statutory rights in Canada.

Manufacturer & Recycling

Imported by: The Source, Barrie, Ontario, Canada, L4M 4W5

Manufactured in China

Website: www.thesource.ca

© 2021 The Source. All rights reserved.

Please Recycle ♻️