Controller Diagram
The controller features a DPad, SELECT, START, B, and A buttons on the top face. Below these are CAPTURE, HOME, TURBO B, and TURBO A buttons. It also includes a USB-C Charge Port and a Micro USB port for firmware updates only.
Receiver Diagram & Included Items
The package includes:
- Origin8 2.4 GHz Wireless Controller
- USB Receiver
- NES Receiver
- 3ft/1m USB to USB-C charge cable
- Instruction Manual
The receivers connect to the respective console ports (USB or NES). The controller has a USB-C port for charging and a Micro USB port for firmware updates.
EN Button Mappings
| Controller | NES® | D-Input | X-Input | Switch |
|---|---|---|---|---|
| DPad | DPad | DPad | DPad | DPad |
| A | A | Button 2 | Button 0 (B) | A |
| B | B | Button 3 | Button 1 (A) | B |
| L | L | Button 7 | Button 4 (LB) | L |
| R | R | Button 8 | Button 5 (RB) | R |
| ZL | - | Button 6 | Button 6 (LT) | ZL |
| ZR | - | Button 5 | Button 7 (RT) | ZR |
| Capture | Capture | Capture | Capture | Capture |
| Home | Home | Home | Home | Home |
| Select | Select | Button 9 | Select | Select |
| Start | Start | Button 10 | Start | Start |
EN Pairing Instructions
- Connect a receiver into the console's controller port and power it on.
- Once powered, the receiver will flash red slowly if unpaired.
- Press and hold the pairing button on the receiver for a few seconds until it flashes rapidly.
- Press Start on the controller to power it on and once more to pair it.
- Once paired, both controller and receiver will have their lights remain on.
- Upon your next play session, you only need to power on the controller with Start to connect to the console receiver on a powered console.
Turbo Function
To enable Turbo Function:
- Flip the switch above Button A and/or B into the "up" position.
- Press and hold the designated button to experience rapid fire inputs.
EN Macros & Compatibility
Macros
Press and hold the button combination for 5 seconds to enable.
| Input | Mode | Description |
|---|---|---|
| Select + Start + R | Clear Pairings | Removes all pairings from the controller. |
| Start + B | Input Switch | Change from D-Input to X-Input, and vice versa. |
| Start + Left | Left Analog | Changes DPad to act as Left Analog. |
| Start + Right | Right Analog | Changes DPad to act as Right Analog. |
| Start + Up | DPad | Changes the DPad back to default. |
Compatibility
- The NES® receiver is compatible with original and most 3rd party clone consoles that utilize the same controller port.
- The USB® receiver is compatible with Windows® PC, Mac®, Android®, Raspberry Pi® devices, MiSTer, Polymega®, Nintendo Switch®, and other USB®-enabled devices and consoles.
EN Troubleshooting
- If you are experiencing connection issues, be sure that the controller is fully charged.
- To reset all connections, press and hold Start + Select + R for 5 seconds.
- To reset the controller, use a thin tool (unbent paperclip) and push a tiny button within the tiny hole on the back of the controller once; this will reset the controller to factory default settings.
EN Support
To stay up to date with the latest news, manuals, and firmware updates, visit retro-bit.com/support.
If you require additional help, e-mail info@retro-bit.com.
Follow us online and stay in the conversation!
- @retrobitgaming
- www.retro-bit.com
Retro-Bit is a registered trademark of Kool Brands, LLC. Mac is a registered trademark of Apple Inc. USB is a registered trademark of Universal Serial Bus Implementers Forum, Inc. Nintendo Switch® is a trademark registered trademark of Nintendo of America Inc. All other mentioned trademarks are either trademarks or registered trademarks of their respective owners. All rights reserved. This product is not endorsed, manufactured, produced, sponsored or licensed by Apple Inc. or Nintendo of America Inc.
Warning
RF exposure statement
This equipment complies with the FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- (1) This device may not cause harmful interference, and
- (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- —Reorient or relocate the receiving antenna.
- —Increase the separation between the equipment and receiver.
- —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- —Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Frequency Range: 2410-2470MHz
RF Output Power: 3.51dBm (EIRP)
Retro-Bit Support
Retro-bit | Homepage
