MOZA CS V2P Steering Wheel
User Manual • Uživatelský manuál • Užívateľský manuál • Használati utasítás • Benutzerhandbuch
Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully before first use and keep this user manual for future reference. Pay particular attention to the safety instructions. If you have any questions or comments about the device, please visit our customer support page: http://www.alza.cz/EN/kontakt.
Quick Release Manual
- Align the six steel ball bearings on the female Quick Release head of the steering wheel with the six grooves on the male Quick Release head of the base.
- Press the Quick Release in the direction of the wheel.
- The Quick Release will automatically lock into place. If it doesn't, try slightly rotating the wheel or remove and reattach it.
- To remove the wheel, press the black section with both hands and pull the wheel out at the same time.
Diagram showing the quick release mechanism being attached.
Steering Wheel Configuration
The CS steering wheel can be configured quickly and easily in the MOZA Pit House software.
- Joystick mode: select between push buttons or cross keys
- RPM indicator switch modes: choose from rpm, off, or constant
- Indicator display modes: choose from mode 1 or mode 2, with detailed explanations available when hovering over the options
- Rev speed prompt setting: four available modes (advanced, standard, extreme, custom) based on the timing between engine rev speed and shift indicator light
- Brightness: adjust the brightness of the shift indicator
- Button color customization: adjust button colors via button combinations
- Button combinations: open the “button combination” tab in the top right corner of the steering wheel settings to view all button inputs and assign functions
- Indicator color adjustment: drag a preferred color block to change the indicator color
- Shifter paddle calibration: if irregularities are detected, click to calibrate
(For full details on settings and functions, please visit the official MOZA Racing website)
Screenshot of the MOZA Pit House software showing steering wheel settings.
Install Heightening Block for Magnetic Paddle
- Place the steering wheel face down on a flat surface.
- Use a hexagonal wrench to remove the screw from the side of the trigger lever on the shift paddle.
- Use a wrench to lift the latch on the side of the magnetic paddle, and pull the trigger lever outward to make room for disassembly.
- Use a hexagonal wrench to remove screws from the shift paddles.
- Install the heightening block using the long screws and tighten them securely.
- Put the latch back in place and secure it with clamp screws.
The heightening block reduces the distance between the magnetic shifter paddles and your hands by 8 mm.
Diagrams showing the installation of the heightening block.
Button Combination Functions
Button combinations allow you to:
- Adjust the maximum steering angle
- Change joystick modes
- Set up dashboard UI
- Configure base parameters and more
Detailed settings are available in the Steering Wheel Settings section of the software.
Warranty Conditions
A new product purchased in the Alza.cz sales network is guaranteed for 2 years. If you need repair or other services during the warranty period, contact the product seller directly, you must provide the original proof of purchase with the date of purchase.
The following are considered to be a conflict with the warranty conditions, for which the claimed claim may not be recognized:
- Using the product for any purpose other than that for which the product is intended or failing to follow the instructions for maintenance, operation, and service of the product.
- Damage to the product by a natural disaster, the intervention of an unauthorized person or mechanically through the fault of the buyer (e.g., during transport, cleaning by inappropriate means, etc.).
- Natural wear and aging of consumables or components during use (such as batteries, etc.).
- Exposure to adverse external influences, such as sunlight and other radiation or electromagnetic fields, fluid intrusion, object intrusion, mains overvoltage, electrostatic discharge voltage (including lightning), faulty supply or input voltage and inappropriate polarity of this voltage, chemical processes such as used power supplies, etc.
- If anyone has made modifications, modifications, alterations to the design or adaptation to change or extend the functions of the product compared to the purchased design or use of non-original components.
EU Declaration of Conformity
This product complies with the legal requirements of the European Union directive(s).
CE WEEE
This product must not be disposed of as normal household waste in accordance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE - 2012/19/EU). Instead, it shall be returned to the place of purchase or handed over to a public collection point for the recyclable waste. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. Contact your local authority or the nearest collection point for further details. Improper disposal of this type of waste may result in fines in accordance with national regulations.
Symbol indicating that the product should not be disposed of as household waste.