CRESTRON M202234003 Dual Easy Fry And Grill Instructions

Instructions for CRESTRON models including: M202234003 Dual Easy Fry And Grill, M202234003, Dual Easy Fry And Grill, Easy Fry And Grill, Fry And Grill, And Grill, Grill

Product Manual: DIN-KXI

DIN-KXI

Product Manual DIN-KXI KNX Secure IP Gateway, DIN Rail Mount

Crestron Electronics, Inc.

Product Manual: DIN-KXI

Mar 28, 2024 — Crestron product development software is licensed to Crestron dealers and Crestron Service Providers (CSPs) under a limited.

DIN-KXI | KNX Secure IP Gateway, DIN Rail Mount | Crestron Electronics, Inc. | AV-iQ

File Info : application/pdf, 30 Pages, 914.96KB

DIN-KXI Manual

View this document in HTML crestron.com/docs/9408
Product Manual
DIN-KXI
KNX Secure IP Gateway, DIN Rail Mount
Crestron Electronics, Inc.

The original language version of this document is U.S. English. All other languages are a translation of the original document.
Regulatory Model: M202234003
Crestron product development software is licensed to Crestron dealers and Crestron Service Providers (CSPs) under a limited nonexclusive, nontransferable Software Development Tools License Agreement. Crestron product operating system software is licensed to Crestron dealers, CSPs, and end-users under a separate End-User License Agreement. Both of these Agreements can be found on the Crestron website at www.crestron.com/legal/software_license_agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed online at www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.
Crestron, the Crestron logo, and 4-Series are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.
©2024 Crestron Electronics, Inc.

Contents
DIN-KXI
Features KNX Security Ethernet Communications Local Diagnostics DIN Rail Installation
Physical Description
Specifications
Product Specifications Dimension Drawings
Installation
In the Box Mounting
Mount to a DIN Rail Remove from a DIN Rail Wiring KNX Bus Connection LAN Connection
Configuration
Acquire with KNX Secure Datapoint Configuration
ETS Software Configuration SIMPL Configuration IP Address Configuration DHCP Address Static IP Address Interface to KNX
Operation
Factory Reset Programming Mode
Resources
Crestron Support and Training Programmer and Developer Resources Product Certificates Related Documentation
Product Manual -- Doc. 9408A

4
5 5 5 5 5 6
8
8 10
11
12 13 13 13 15 15 15
16
17 20 20 21 24 24 25 26
28
28 28
29
29 29 29 29
Contents · iii

DIN-KXI
KNX Secure IP Gateway, DIN Rail Mount
The DIN-KXI is an IP-based KNX interface that allows a 4-Series® Control System to communicate with a KNX system. It is capable of addressing and controlling up to 1,000 datapoints and receives power over the KNX bus. The DIN-KXI can also be used as a programming interface for KNX devices using ETS5 and ETS6 software. This section provides the following information:
· Features · Physical Description

Product Manual -- Doc. 9408A

DIN-KXI · 4

Features
Key features include:
l 1M wide DIN rail mounting l Ethernet to KNX interface l Integrates KNX with a Crestron® control system l Supports KNXnet/IP Security (AES-128) l Controls up to 1,000 KNX datapoints l Up to 8 simultaneous KNXnet/IP Tunneling connections l Configure using ETS Software l On-board controls for setup and diagnostics l Powered via the KNX bus
KNX Security
The device supports KNX Security (AES-128) which can be enabled using ETS software.
Ethernet Communications
The Ethernet connection allows access to the KNX bus from any point on the LAN. This provides programming and diagnostics without direct access to the DIN-KXI.
Local Diagnostics
The buttons and LEDs on the device provide diagnostic data including the operating status and communication errors.
DIN Rail Installation
The 1M 18 mm (0.70 in) wide DIN-KXI snaps onto a standard DIN rail for installation in a wall mount enclosure. Wiring connections are made using screw terminals positioned along the bottom, clearly accessible from the front for easy installation and servicing. All setup controls and indicators are positioned on the center front panel. When installed in an enclosure utilizing 45mm cutouts, the DINKXI's front panel stays accessible while the connections are concealed.

5 · DIN-KXI

Product Manual -- Doc. 9408A

Physical Description
The DIN-KXI provides the following connectors, controls, and indicators. The following illustrations shows the front, top, and bottom of the DIN-KXI. For additional details, refer to Specifications on page 8 and Operation on page 28. DIN-KXI Front View

DIN-KXI Top and Bottom View Product Manual -- Doc. 9408A

DIN-KXI · 6

KNX Connector: Connects to the KNX system and receives power from the KNX bus. KNX Prog.: LED and recessed push button to enter Programming mode and to perform a factory reset. KNX: The LED lights to indicate power and KNX status. Mode: The LED lights to indicate the BAOS and IP tunnel status. IP: The LED lights to indicate the Ethernet status. CONN BAOS: Provides manual configuration and selection of the BAOS connection. CONN TUNN: Provides manual configuration and selection of a tunnel connection. P/ESC: Press CONN BAOS and CONN TUNN to exit manual configuration. RJ-45: Connects to the LAN to provide communications between the control system and DIN-KXI.

7 · DIN-KXI

Product Manual -- Doc. 9408A

Specifications
Product specifications for the DIN-KXI.
Product Specifications

Power KNX Bus

20mA

Communications KNX
Ethernet

KNX over TP (Twisted Pair); Interface protocol: cEMI; Max. APDU length: 55; Device model: System B; KNXnet/IP Security (AES-128); Compatible with ETS5 and ETS6
Supports ARP, ICMP, IGMP, UDP/IP, TCP/IP, DHCP, and Auto IP; DHCP is enabled by default, can be changed using the ETS Software

Connectors KNX
LAN

(2) 4-conductor KNX bus connectors, push-in style; Consisting of (1) Red (+) and (1) Black (-) connector, for power and communications; Accepts up to 4 solid-core twisted pairs; 0.6 - 0.8 mm (22 - 20 AWG), strip wires 5 - 6 mm (0.2 - 0.24 in.)
(1) 8-pin RJ-45, female; 100BASE-TX Ethernet port; Green and yellow LEDs indicate Ethernet port status

Controls and Indicators

KNX PROG.

(1) Red LED and (1) recessed, miniature push button for entering Programming mode and factory reset; Programming Mode: Press to enter Programming mode, the LED lights to indicate that Programming mode is activated; Factory reset: Press and hold while connecting the KNX bus, hold for 6 seconds until all LEDs flash

KNX

(1) Multicolor LED, indicates power and KNX status; Green: Indicates power is received from the KNX bus; Flashing Green Indicates communications on the KNX bus; Flashing Red: Indicates communications failure on the KNX bus

Product Manual -- Doc. 9408A

DIN-KXI · 8

MODE
IP CONN BAOS CONN TUNN

(1) Multicolor LED, indicates BAOS and IP tunnel status; Green: Normal operating mode; Red: Programming mode is active; Flashes green (1 to 10 times): Manual mode is active, the selected BAOS connection (1 to 10) is not used and is available, the number of flashes indicates the connection number; Flashes Orange (1 - 10 times): Manual mode is active, the selected BAOS connection (1 - 10) is used; Flashes Green (1 - 5 times): Manual mode is active, the selected Tunnel (1 - 5) is not used and is available; Flashes Orange (1 - 5 times): Manual mode is active, the selected Tunnel (1 - 5) is used; Flashes Red: The configuration is not properly loaded
(1) Multicolor LED, indicates Ethernet status; Green: Active Ethernet link and valid IP settings; Flashes green: Ethernet activity; Red: Invalid IP settings or has not received IP settings from the DHCP server
(1) push button, to enter Manual mode and select a BAOS connection; Press to enter Manual mode and select a BAOS connection (1 - 10), the MODE LED indicates the selected BAOS connection number; To exit Manual mode, press CONN BAOS and CONN TUNN simultaneously
(1) push button, to enter Manual mode and select a tunnel connection; Press to enter Manual mode and select a TUNN connection (1 - 5), the MODE LED indicates the selected tunnel connection number; To exit Manual mode, press CONN BAOS and CONN TUNN simultaneously

Environmental Temperature Humidity

-5° to 45°C (23° to 113°F) 5% to 93% RH (noncondensing)

Construction Enclosure Mounting

Light gray polycarbonate housing with polycarbonate label overlay
35 mm DIN EN 60715 rail mount, DIN 43880 form factor for enclosures with 45 mm front panel cutout, occupies 1 DIN module space (18 mm)

Dimensions Height Width
Depth

91 mm (3.57 in.) 18 mm (0.70 in); 1M wide 60 mm (2.36 in.)

Weight 40 g (1.41 oz)

Compliance
Regulatory Model: M202234003 CE

9 · DIN-KXI

Product Manual -- Doc. 9408A

Dimension Drawings

Product Manual -- Doc. 9408A

DIN-KXI · 10

Installation
This section provides the following information:
· In the Box · Mounting · Wiring

11 · DIN-KXI

Product Manual -- Doc. 9408A

In the Box

Qty.

Description

DIN-KXI, KNX Secure IP Gateway, DIN Rail Mount

Additional Items

KNX Certificate Label (2062600)

Product Manual -- Doc. 9408A

DIN-KXI · 12

Mounting
NOTE: Observe the following points when installing the DIN-KXI. l Use the DIN-KXI in an electrical panel with DIN rail mounting provisions. l Mount the DIN-KXI in a well-ventilated area.
Mount to a DIN Rail
To mount the DIN-KXI to a DIN rail: 1. Hang the DIN-KXI on the top of the DIN rail. When the DIN-KXI is mounted, the certificate label with the serial number, MAC address, and KNX certificate number may not be visible. A duplicate of the KNX certificate label (2062600) is included that can be placed inside the enclosure. 2. Press the bottom toward the DIN rail and snap it into place.

Remove from a DIN Rail
To remove the DIN-KXI DIN Rail: 1. Turn off power to the device. 2. Remove all connections from the DIN-KXI.
13 · DIN-KXI

Product Manual -- Doc. 9408A

3. Use a small, flat-head screwdriver to pull the DIN rail release tab down. 4. Tilt the bottom of the DIN-KXI away from the bottom of the DIN rail and then remove the device.

Product Manual -- Doc. 9408A

DIN-KXI · 14

Wiring
NOTE: When wiring the DIN-KXI, connect the device to the KNX bus that uses a KNX power supply.
KNX Bus Connection
To wire the KNX bus, connect the black (-) and red (+) terminals to the KNX bus
LAN Connection
To connect to the local LAN, connect an ethernet cable to the RJ-45 port.

15 · DIN-KXI

Product Manual -- Doc. 9408A

Configuration
This section provides the following information:
· Acquire with KNX Secure · Datapoint Configuration · IP Address Configuration · Interface to KNX

Product Manual -- Doc. 9408A

DIN-KXI · 16

Acquire with KNX Secure
Use the info on the KNX label to acquire the DIN-KXI. The Factory Key (FSDK) for the device is on the DIN-KXI label and also on the spare label that is provided. On the label, the Factory Key (FSDK) is labeled Cert.
NOTE: When the configuration is changed, the settings must be downloaded onto the DIN-KXI. For details, refer to ETS Software documentation.
For additional information about KNX Secure and using ETS software, visit www.knx.org, support.knx.org, or Adding device certificates. To add the KNX Secure device using ETS software:
1. Assign a password to the project in ETS software before adding the DIN-KXI to the project. A secure device cannot be added to a project that is not password protected.

2. Find the DIN-KXI using the Online Catalog that is available in ETS software version 5.6.5 or later. For earlier versions of ETS software or when the Online Catalog is not enabled, use the offline catalog available from the DIN-KXI product page.

17 · DIN-KXI

Product Manual -- Doc. 9408A

3. Add the DIN-KXI to ETS software. The Factory Key can be entered on the Security tab or before downloading the device. Scan the QR code on the label using the device running the ETS software or enter the certificate number (Cert) manually.

Product Manual -- Doc. 9408A

DIN-KXI · 18

4. In the Parameters tab, select General settings and then configure the following:

l Prog. mode on device front: To allow use of the Prog. mode button on the front of the device, select Enabled.
l Manual operation on device: To allow use of the CONN BAOS and CONN TUNN buttons to enable manual operation on the front of the device, select Enabled with a time limit from the drop-down menu.
l Object server: To use a secure connection to the Object server, from Communication select Secure, in the Password field enter a password, and then from the Object server port dropdown menu enter an object server port number.
Configure the DIN KXI IO module in the SIMPL program using the same settings. For configuration information, refer to the Help (F1) file (PDF) that is provided for the module.
5. In the Parameters tab, select Datapoints and then configure the datapoints in ETS software and the SIMPL program. For details, refer to Datapoint Configuration on page 20.

19 · DIN-KXI

Product Manual -- Doc. 9408A

Datapoint Configuration
Configure up to 1,000 datapoints in the system using ETS software and SIMPL modules.
NOTE: When the configuration is changed, the settings must be downloaded onto the DIN-KXI. For details, refer to ETS Software documentation.
ETS Software Configuration
Each data point gets a group address, in order to send to the bus. More than one group address can be set for one object. To access the datapoints, go to the Parameters tab and then select Datapoints. DIN-KXI Datapoints Tab

Product Manual -- Doc. 9408A

DIN-KXI · 20

For each datapoint that is used in the system, configure these settings:
l Datapoint number (1 - 1000): The object id number. The datapoints are listed in groups of 10. l Datapoint type: Select the type of object from the drop-down menu. If the datapoint is not used,
select Disabled. The SIMPL modules provide control of 1 Bit, 2 Bit, 4 Bit, 8 Bit, 1 Byte, 2 Byte, 3 Byte, 4 Byte, 6 Byte, and 14 Byte datapoint types. l Description: Enter a short description (30 character maximum) of the datapoint. The description is transferred to the device when Download of data point description option is enabled.
NOTE: To utilize polling, select the Read option in ETS software.
SIMPL Configuration
For each datapoint configured in ETS software, use SIMPL to configure the Crestron control system to interface with the KNX system. In SIMPL, go to Crestron Modules > System Control and then use the DIN KXI modules.
Each Crestron module allows specific KNX commands or signals to be sent or read. One module can provide control, feedback, or both. Do not add multiple modules for the same object to get control and feedback using two modules.
Modules are available to control these datapoint types:
l Datapoint 1: 1 Bit, Switch l Datapoint 1: 1 Bit, Switch l Datapoint 2: 2 Bit, Switch and Control l Datapoint 3: 4 Bit, Dimming l Datapoint 4: 8 Bit, Character ASCII l Datapoint 5: 8 Bit, Percent Value l Datapoint 6: 8 Bit, Signed Value l Datapoint 7: 2 Byte, Unsigned Value l Datapoint 8: 2 Byte, Signed Value l Datapoint 9: 2 Byte, Temperature l Datapoint 10: 3 Byte, Time l Datapoint 11: 3 Byte, Date l Datapoint 12: 4 Byte, Unsigned Value l Datapoint 13: 4 Byte, Signed Value l Datapoint 14: 4 Byte, Float Value l Datapoint 15: 4 Byte, Access l Datapoint 16: 14 Byte, String l Datapoint 17: 1 Byte, Scene l Datapoint 18: 1 Byte, Scene with Control l Datapoint 20.102: 1 Byte, HVAC Mode

21 · DIN-KXI

Product Manual -- Doc. 9408A

l Datapoint 232.600: 3 Bytes, Color RGB l Datapoint 251.600: 6 Bytes, Color RGBW
Required Modules
These modules are required: l One DIN KXI IO module to communicate with the DIN-KXI. l One DIN KXI x Bit or DIN-KXI x Byte module per KNX object.
SIMPL Modules
The DIN-KXI modules can control datapoints with these Bit and Byte types. For information about each DIN KXI SIMPL module, refer to the Help (F1) file (PDF) that is provided for each module.
DIN-KXI 1 Bit
l Datapoint 1: 1 Bit, Switch
DIN-KXI 1 Bit Pulse
l Datapoint 1: 1 Bit, Switch
DIN-KXI 2 Bit
l Datapoint 2: 2 Bit, Switch and Control
DIN-KXI 4 Bit
l Datapoint 3: 4 Bit, Dimming
DIN-KXI 1 Byte
l Datapoint 4: 8 Bit, Character ASCII l Datapoint 5: 8 Bit, Percent Value l Datapoint 6: 8 Bit, Signed Value l Datapoint 17: 1 Byte, Scene l Datapoint 18: 1 Byte, Scene with Control l Datapoint 20.102: 1 Byte, HVAC Mode
DIN-KXI 2 Byte
l Datapoint 7: 2 Byte, Unsigned Value l Datapoint 8: 2 Byte, Signed Value l Datapoint 9: 2 Byte, Temperature
DIN-KXI 3 Byte
l Datapoint 232.600: 3 Bytes, Color RGB

Product Manual -- Doc. 9408A

DIN-KXI · 22

DIN-KXI 4 Byte
l Datapoint 12: 4 Byte, Unsigned Value l Datapoint 13: 4 Byte, Signed Value l Datapoint 14: 4 Byte, Float Value l Datapoint 15: 4 Byte, Access
DIN-KXI 6 Byte
l Datapoint 251.600: 6 Bytes, Color RGBW
DIN-KXI 14 Byte
l Datapoint 16: 14 Byte, String
DIN-KXI Time
l Datapoint 10: 3 Byte, Time
DIN-KXI Date
l Datapoint 11: 3 Byte, Date

23 · DIN-KXI

Product Manual -- Doc. 9408A

IP Address Configuration
The DIN-KXI uses an IP address that is automatically assigned using DHCP (default) or manually assigned using a static IP address.
NOTE: When the configuration is changed, the settings must be downloaded onto the DIN-KXI. For details, refer to ETS Software documentation.
ETS Software - IP Address Properties

DHCP Address
The DIN-KXI uses DHCP (default setting) to obtain an IP address. The DHCP server will assign an IPaddress to the Crestron DIN-KXI.

Product Manual -- Doc. 9408A

DIN-KXI · 24

Static IP Address
To use a static IP address:
1. Go to the DIN-KXI properties and then select IP. 2. Select Use a static IP address. 3. Enter the IP Address, Subnet Mask, and Default Gateway.

25 · DIN-KXI

Product Manual -- Doc. 9408A

Interface to KNX
The DIN-KXI can act as an interface to KNX system and allow multiple simultaneous connections.
NOTE: When the configuration is changed, the settings must be downloaded onto the DIN-KXI. For details, refer to ETS Software documentation.
In order to use this function, configure the connections using the Manage Configured Connections screen in ETS software. ETS Software - Manage Configured Connections

Product Manual -- Doc. 9408A

DIN-KXI · 26

There are nine tunneling connections available to the KNX bus. ETS Software - Tunneling Interface Connections

27 · DIN-KXI

Product Manual -- Doc. 9408A

Operation
Use the buttons located on the front of the DIN-KXI to factory reset the device or enter programming mode.
Factory Reset
To factory reset the device: 1. Disconnect the device from the KNX bus to turn it off. 2. Press and hold KNX Prog. Do not release the button. 3. Reconnect the device to the KNX bus to turn it on. 4. Continue holding KNX Prog until all LEDs flash quickly. Then, release the KNX Prog button.
Programming Mode
To enter or exit Programming mode, press KNX Prog. Alternatively, simultaneously press CONN BAOS and CONN TUNN to enter or exit Programming mode.

Product Manual -- Doc. 9408A

DIN-KXI · 28

Resources
The following resources are provided for the DIN-KXI.
NOTE: You may need to provide your Crestron.com web account credentials when prompted to access some of the following resources.
Crestron Support and Training
l Crestron True Blue Support l Crestron Resource Library l Crestron Online Help (OLH) l Crestron Training Institute (CTI) Portal
Programmer and Developer Resources
l help.crestron.com: Provides help files for Crestron programming tools such as SIMPL, SIMPL#, and Crestron ToolboxTM software
l developer.crestron.com: Provides developer documentation for Crestron APIs, SDKs, and other development tools
Product Certificates
To search for product certificates, refer to the Product Certificates section of the Crestron Resource Library.
Related Documentation
l www.knx.org l support.knx.org

29 · DIN-KXI

Product Manual -- Doc. 9408A

Crestron Electronics, Inc. 15 Volvo Drive, Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7656 www.crestron.com

Product Manual -- Doc. 9408A 03/28/24
Specifications subject to change without notice.