ANZZI GLASS SHOWER DOOR INSTALLATION & OPERATION MANUAL

Product Registration

IMPORTANT: Warranty will not be recognized unless product is registered.

Register your product within 90 days to ensure it is recognized as a purchase and covered under warranty.

Register online at https://anzzi.com/pages/register or scan the QR code on PG. 2.

Registering your product maximizes your warranty benefits and ensures prompt service and support.

Steps to Register:

1. USE YOUR PHONE CAMERA TO SCAN THE QR CODE
2. FILL IN A QUICK REGISTRATION FORM
3. CLICK SUBMIT AND ENJOY PEACE OF MIND

Need help? For technical support call 305-614-4070 or visit us at www.ANZZI.com

STOP! READ BEFORE YOU PROCEED!

TO KEEP GLASS FROM BREAKING, MAKE SURE:

1. Due to the weight of this product, at least two people are needed for a safe installation.
2. Glass corner protectors remain on during installation.
3. Glass protective seals are mounted to the door before opening/closing.
4. Glass panels are aligned & level with wall/floor.
5. Stoppers must be installed correctly. Prevents door from striking wall.
6. Slider must be installed correctly for smooth sliding.

SAFETY PRECAUTIONS

General Safety Warnings

1. Read Instructions First – Carefully read the entire installation manual before beginning. Improper installation may result in product failure or injury.
2. Use Proper Tools – Always use the recommended tools and hardware to ensure safe and correct installation.
3. Work with a Partner – Due to the weight and fragility of glass panels, never attempt to install them alone. A minimum of two people is required.

Handling Tempered Glass Panels

1. Do Not Strike or Edge-Load the Glass – Tempered glass is strong but can shatter if struck on its edges or corners.
2. Always Carry Glass Vertically – Transport and handle glass panels in an upright position to reduce the risk of breakage.
3. Wear Protective Gear – Use safety gloves, closed-toe shoes, and eye protection when handling glass.
4. Inspect Before Installation – Check for cracks, chips, or defects before installation. Do not install damaged glass panels.
5. Do Not Drill or Modify the Glass – Altering the glass in any way can compromise its integrity and cause it to shatter.
6. Keep the Glass in a Secure Area Until Installation – Store glass panels upright on a non-slip surface, away from heavy traffic areas.
7. Avoid Sudden Temperature Changes – Do not expose tempered glass to extreme temperature shifts, as this can cause it to shatter.

Installation Precautions

1. Secure the Work Area – Ensure the installation site is free of obstacles, water, or debris to prevent slipping or dropping the glass.
2. Check Wall and Floor Strength – Ensure mounting surfaces are sturdy enough to support the shower door assembly.
3. Tighten Fasteners Securely but Cautiously – Over-tightening hardware can stress and damage glass components.
4. Follow Manufacturer's Weight Limits – Ensure that the structure can support the weight of the installed shower doors.

Post-Installation Warnings

1. Do Not Slam the Doors – Forcefully closing shower doors can cause damage or breakage over time.
2. Regularly Check for Loose Hardware – Periodically inspect hinges, rollers, and handles for stability.
3. Do Not Hang Items on Glass Doors – Hanging towels or objects on the doors may stress the hardware or glass, leading to breakage.

WARNING PROTECTIVE EQUIPMENT MUST BE WORN WHEN HANDLING GLASS

INSTALLATION GUIDE

BEFORE YOU BEGIN

• Please check the product for damage and missing parts immediately upon delivery. Damage reported after installation will not be covered under our warranty. Please handle the product with care. Avoid impacting the sides and edges of the glass.
• Consult your local building codes before installation.
• To reduce the risk of breakage, keep the corner protectors on the glass during installation.
• If this unit is being installed in new construction, please install all required plumbing and drainage before installing the shower. Use a licensed plumber or contractor for all plumbing installations if required by local code.
• Before beginning installation, make sure all surfaces are level, solid and will support the total weight of the unit. Also, make sure the walls are at right angles. An uneven installation surface, rounded corners, or improperly angled side walls can cause serious installation problems. Please note that some adjustments and drilling might be necessary during the installation process.
• Protect all primary surfaces of the product during installation. Never place the glass directly on a tile floor. Keep the corner protectors in place until they need to be removed. Always use wood or cardboard to protect the bottom edge and corners of the glass before and during installation.

WARNING

• Install this unit on a finished threshold and against finished walls.
• Avoid drilling into hidden pipes or electrical cables when making holes in the walls.
• Due to the weight of this product, at least two people are needed for a safe installation.
• When cutting or drilling metal components or handling glass, wear protective eyewear, gloves, and closed-toe shoes to minimize the risk of personal injury.
• Failure to follow these instructions may result in personal injury, property damage, or product failure, and could void the warranty.

BEFORE YOU BEGIN

ATTENTION

• Surface of the threshold or tub deck must be level for proper installation.
• This model requires a minimum 3.15" (80 mm) flat level threshold or tub deck space for installation.

Tools Required

• Phillips Screwdriver
• Tape Measure
• Drill
• 1/8" (3mm) Drill Bit
• 7/32" (5.5mm) Drill Bit
• 5/16" (8mm) Drill Bit
• 100% Silicone Sealant
• Pencil
• Rubber Mallet
• Safety Glasses
• Hack Saw
• Metal File
• Tin Snips
• Stud Finder
• Knife
• Level

WARNING This product is heavy and requires two people to install.

WARNING Use cut-resistant, non-slip gloves to reduce the risk of personal injury and to hold the glass firmly.

PARTS

WARNING To prevent damage to glass and potential injury, carefully follow the instructions on page 4.

[02]x1 [03]x1 [05]x1

[06]x1 [13]x2 [14]x1 [15]x1 [17]x2 [21]x1

[01]x2 [04]x2 [07]x2 [08]x2 [09]x3 [10]x3 [11]x5

[12]x1 [16]x7 [18]x7 [19]x2 [20]x1 [22]x1 [23]x1

ASSEMBLY

WARNING To prevent damage to glass and potential injury, carefully follow the instructions on page 4.

SD-AZ13-01**(SD-AZ8077-01**) 48"x76"

Dimensions are shown in inches and millimeters.

SD-AZ13-02**(SD-AZ8077-02**) 60"x76"

Dimensions are shown in inches and millimeters.

SD-AZ13-03** 54"x76"

Dimensions are shown in inches and millimeters.

SD-AZ17-01**(SD-AZ8080-01**) 60"x62"

Dimensions are shown in inches and millimeters.

INSTALLATION INSTRUCTIONS

BEFORE YOU BEGIN

ATTENTION

• To avoid personal injury or property damage, identify components and read all instructions before installing.
• This model requires a minimum 3.15" (80mm) of flat level threshold or tub deck space for installation. (Dimension "D" of Fig 1.)
• This manual shows right side installation. For left side installation, follow the instructions in page 27.

Step 1

1. Measure the finished opening width at the bottom or tub surface ("W2") and at the top ("W1"). The height of top: SD-AZ13-01/SD-AZ13-02/SD-AZ13-03: H=72.7"[1847mm]; SD-AZ17-01: H = 58.7" [1491mm].
2. IMPORTANT: If the widths of the Support Bar [03], Bottom Rail [15] and the Rail Cover [14] align correctly, cutting is unnecessary. If they don't, please see setp 2 for cutting instructions.
3. Remove the Wall Brackets [08]. Using a pencil or another marking tool (such as masking tape), mark distance W-05"(12.7mm) on the Support Bar [03] (to leave some space for the Wall Brackets), W2 on the Bottom Rail [15], C on the Rail Cover [14].
4. IMPORTANT: Double check the measurements before cutting. Cut the Support Bar [03] on the Door [05] end only. Cut the Support Bar [03], Bottom Rail [15] and the Rail Cover [14] with a fine toothed (32 TPI) hack saw. If needed, use a metal file to smooth rough edges. Clean up metal shavings.
5. DO NOT stand on or use a vice to hold the Support Bar [03], Bottom Rail [15] and the Rail Cover [14] while cutting.

Step 2

• This shower door must be mounted to a stud. Minimum threshold space is required.
• IMPORTANT: Using a stud finder, ensure the wall intended to hold the door has a stud at the installation point. A stud in this location must be identified to support the support bar in order to proceed with the installation. If there is no stud in the shown area, we recommend employing a qualified contractor to install one.

1. If this shower door is intended to be installed with Bottom Rail [15] flushing with the outside wall, position the Template [23] to the side wall of shower room with one of its side flush with the outside wall. (Fig 2.1)
2. If this shower door is intended to be installed with Bottom Rail [15] behind the outside wall, position the Template [23] to the side wall of shower room with one of its side A" behind the outside wall. A" is the distance between the side of the Template [23] and the outside wall. (Fig 2.2)
3. Use a pencil to mark the screw holes on the wall through the Template [23]. (Fig 2.1, Fig 2.2)
4. Use a pencil to draw a line on the side wall along the side of Template [23] near the threshold. (Fig 2.2)
5. IMPORTANT:
   • Make sure there are studs behind the positions of the screw holes.
   • Ensure the marks on the side walls are equidistant from the outside wall.

Step 3

1. Drill 5/16" holes at the location marked in Step 2 (Figure 3.1).
2. Insert the Anchors [09]. (Fig 3.2)
3. Remove the Wall Bracket Plates from Wall Brackets[08] and secure them with Screws[10] using Screw Driver Bit [22]. (Fig 3.3)
4. Slightly Slide the Wall Brackets[08] to the Support Bar [03] and install to the Wall Bracket Plates. Slightly push and turn the Wall Brackets [08] clockwise until it stop. Reverse the Wall Brackets [08] a little so that its screw holes point upward. (Fig 3.4)

Step 4a - FOR SHOWER DOOR INSTALLATION

Notice: The Bottom Rail [15] and Guide Block [12] can be secure by silicone sealant. For screw free installation, skip to step 4, 5 of this page.

1. If this shower door is intended to be installed with Bottom Rail [15] flushing with the outside wall, slightly position the Bottom Rail [15] flushing with the outside wall. If this shower door is intended to be installed with Bottom Rail [15] behind the outside wall, slightly position the Bottom Rail [15] with outer side of it aligns with the marked lines on the side wall. Mark the screw holes through the Bottom Rail [15]. (Fig 4a.1)
2. NOTE: Ensure the groove pattern on Bottom Rail [15] faces upwards before proceeding.
3. Remove the Bottom Rail [15] and drill a 1/8" hole at each marked location if drilling into acrylic or wood material. Drill a 7/32" hole if drilling into tile material and insert the Small Anchors [18]. (Fig 4a.2, Fig 4a.3)
4. Secure the Bottom Rail [15] with Screws [16]. Then, skip to Step 5. (Fig 4a.4)
5. Apply a good quality of Silicone Sealant to the slots of Bottom Rail [15] and place it to the marked threshold. (Fig 4a.1, Fig 4a.5)
6. Apply a good quality of Silicone Sealant to the slots and bottom surface of Guide Block [12] and place it close to the center of back surface of Bottom Rail [15] facing to the shower room. Allow 24 hours for the silicone to cure before next step. (Fig 4a.6, Fig 4a.7)

Step 4b - FOR BATHTUB DOOR INSTALLATION

Notice: The Bottom Rail [15] and Guide Block [12] can be secure by silicone sealant. For screw free installation, skip to step 4, 5 of this page.

1. If this shower door is intended to be installed with Bottom Rail [15] flushing with the outside wall, slightly position the Bottom Rail [15] flushing with the outside wall. If this shower door is intended to be installed with Bottom Rail [15] behind the outside wall, slightly position the Bottom Rail [15] with outer side of it aligns with the marked lines on the side wall. Mark the screw holes through the Bottom Rail [15]. (Fig 4b.1)
2. NOTE: Ensure the groove pattern on Bottom Rail [15] faces upwards before proceeding.
3. Remove the Bottom Rail [15] and drill a 1/8" hole at each marked location if drilling into acrylic or wood material. Drill a 7/32" hole if drilling into tile material and insert the Small Anchors [18]. (Fig 4b.2, Fig 4b.3)
4. Secure the Bottom Rail [15] with Screws [16]. Then, skip to Step 5. (Fig 4b.4)
5. Apply a good quality of Silicone Sealant to the slots of Bottom Rail [15] and place it to the marked threshold. (Fig 4b.1, Fig 4b.5)
6. Apply a good quality of Silicone Sealant to the slots and bottom surface of Guide Block [12] and place it close to the center of back surface of Bottom Rail [15] facing to the shower room. Allow 24 hours for the silicone to cure before next step.(Fig 4b.6,Fig 4b.7)

Step 5

WARNING To prevent damage to glass and potential injury, carefully follow the instructions on page 4.

1. Remove the Cover, Screw, Eccentric Block, and Gasket from one of the Rollers [04]. Attach the Stopper and Washer to one of the upper holes on the front of the Door [05]. Install Eccentric Block and Gasket to the Stopper from the back of the Door [05] and secure with the Screw using the matched Allen Key [11]. Using one provided small Allen Key [11] to stick into the side hole of Roller [04] and press the Stopper of it. Adjust the Eccentric Block until its side hole points upward. Then, tighten the Screw using another Allen Key [11] to secure Roller [04]. Install the second Roller [04] to the other upper hole using the same process. (Fig 5.1, Fig 5.2)
2. IMPORTANT: Ensure that there are Washers between Roller [04] and Door [05]. Two side holes of the Door[05] should be on the side closed to the wall when the Rollers [04] face outside. (Fig5.1, Fig 5.2)
3. Remove two of the Corner Protectors and install a Water Sealing Strip [13] to the right side of Door [05]. Make sure the end of Water Sealing Strip [13] is aligned with the bottom of the Door[05]. If the Water Sealing Strip [13] is longer than the Door [05] after installation, cut it to correct length. (Fig 5.1, Fig 5.3)
4. Carefully move the Door [05] to the shower room. (Fig 5.3)
5. NOTE: Slightly place Door [05] with cloth or blanket between it and the floor.

Step 6

WARNING To prevent damage to glass and potential injury, carefully follow the instructions on page 4.

1. Slightly lay down the Fixed Panel [02] on the floor with soft cloth or foam block underneath. Remove the Corner Protectors except the one at the top right corner of Fixed Panel [02].
2. Install Water Sealing Strip [13] to the Fixed Panel [02]. Make sure the end of Water SealingStrip [13] is 0.5" from the bottom of Fixed Panel [02]. (Fig 6.1)
3. If the Water Sealing Strip [13] is longer than the Fixed Panel [02] after installation, cut it to correct length. (Fig 6.1)
4. Install the Glass Bottom Protection Seal [21] to the bottom of Fixed Panel [02]. (Fig 6.1) Note: Failure to install the Glass Bottom Protection Seal [21] will void the warranty.
5. Apply a good quality Silicone Sealant to the bottom of the Glass Bottom Protection Seal [21]. (Fig 6.2)
6. Carefully lift up the Fixed Panel [02] and install it to the Bottom Rail [15]. Make sure the Fixed Panel [02] is set closed to the Fixed Block [07] and the Water Sealing Strip [13] faces to the side wall. (Fig 6.2, Fig 6.3)
7. Remove the Covers and Washers from the Fixed Blocks [07]. Slightly push the Fixed Panel [02] to the side wall and pull it down into the groove of Bottom Rail [15] . (Fig 6.3)
8. Slightly push the Fixed Panel [02] to the Fixed Blocks [07] so that its holes match the protrusions of the Fixed Blocks [07]. Make sure there are Gaskets between the Fixed Panel [02] and the Fixed Blocks [07]. If the holes of Fixed Panel [02] don't match well with the protrusions of the Fixed Blocks [07], loose the Screws of Fixed Blocks [07] and adjust them until the protrusions instert to the holes. Tighten the Screws of Fixed Blocks [07]. (Fig 6.3, Fig 6.4)
9. Install the Washers and Covers back to the Fixed Blocks [07]. Insert a small Allen Key [11] to the side holes of Covers and tighten the Covers to secure. (Fig 6.3)
10. Tighten the hex screws of the Wall Brackets [08] to secure the Support Bar [03]. (Fig 6.5)

Step 7a - FOR SHOWER DOOR INSTALLATION

Notice: This page is for Guide Block [12] secured by screws only. For screw free installation, skip to Step 4a at page 16.

1. Draw Center Line at the middle of the threshold. Place the Guide Block [12] close to the center of back surface of Bottom Rail [15] facing to the shower room. Mark the screw holes of the Bottom Rail [15] on the threshold. (Fig 7a.1)
2. Remove Guide Block [12] and drill 1/8" holes at each marked location if drilling into acrylic or wood material. Drill 7/32" holes if drilling into tile material and insert the Small Anchors [18]. (Fig 7a.2, Fig 7a.3)
3. Secure the Guide Block [12] with Screws [16]. (Fig 7a.4)

Step 7b - FOR BATHTUB DOOR INSTALLATION

Notice: This page is for Guide Block [12] secured by screws only. For screw free installation, skip to Step 4b at page 17.

1. Draw Center Line at the middle of the threshold. Place the Guide Block [12] close to the center of back surface of Bottom Rail [15] facing to the shower room. Mark the screw holes of the Bottom Rail [15] on the threshold. (Fig 7b.1)
2. Remove Guide Block [12] and drill 1/8" holes at each marked location if drilling into acrylic or wood material. Drill 7/32" holes if drilling into tile material and insert the Small Anchors [18]. (Fig 7b.2, Fig 7b.3)
3. Secure the Guide Block [12] with Screws [16]. (Fig 7b.4)

Step 8

WARNING To prevent damage to glass and potential injury, carefully follow the instructions on page 4.

1. Carefully lift up the Door [05] and place the Roller [04] on the Support Bar [03]. Make sure the Door [05] is in the groove of the Guide Block [12]. (Fig 8.1)
2. Use a matched Allen Key [11] to unscrew the Limit Stop [01] on the door end and adjust it to the position 2.76" minimum away from the wall. Tighten the screw of Limit Stop [01] to secure it. Slightly push the Door [05] to the wall. The Water Sealing Strip [13] should be touched the wall. If it doesn't, adjust the position of the Limit Stop [01] again. (Fig 8.2)
3. Slightly push the Door [05] to the wall to check if the Water Sealing Strip [13] align with the wall. If it doesn't, loosen the Screw of Roller [04] and turn the Eccentric Block to adjust the position of Door [05]. Adjust the other Roller [04] if needed. Remember to retighten the screw after the adjustment. (Fig 8.3,Fig 8.4)
4. Unscrew another Limit Stop [01] on the end of Fixed Panel [02] and adjust it to the position 3.6" minimum away from the wall. Tighten the screw of Limit Stop [01] to secure it. (Fig 8.5)

Step 9

1. Disassemble the Roller Guards [19] and install it to the Door [05] as the figure shows. (Fig 9)
2. Install the Rod and one Washer from the front of the Door [05], install the Nut assembly from the back of Door [05]. Hold the Rod by hand and use a matched Allen Key [11] to stick to the side hole of the Nut and tighten it to secure. If the Rod is too close to the Support Bar [03], turn the Nut in counter-clockwise.

Step 10

1. Remove the Corner Protectors and install a Water Sealing Strip [17] to the side of Door [05]. Make sure the end of Water Sealing Strip [17] installed to the Door [05] is aligned with the bottom of it. If the Water Sealing Strip [17] is longer than the Door [05] after installation, cut it to correct length. The flange should be faced outside. (Fig 10.1)
2. Remove the Corner Protectors and install the Water Sealing Strip [17] to the side of Fixed Panel [02]. Make sure the end of Water Sealing Strip [17] installed to Fixed Panel [02] is 0.08" [2mm] above from the Bottom Rail [15]. If the Water Sealing Strip [17] is longer than the Fixed Panel [02] after installation, cut it to correct length. The flange should be faced inside. (Fig 10.3)
3. Cut a section from the top of the Water Sealing Strips [17] using the measurements from Fig 10.2 & Fig 10.4.

Step 11

1. Disassemble the Handle Set [06] and install to the Door [05]. Install Handle, Flange and Washer from the front of the Door [05]. Install Washer, Lever and Fixed Block from the back of the Door [05]. (Fig 11.1)

Step 12

1. Apply a good quality Silicone Sealant at the inner corner form by the Bottom Rail [15] and Threshold, inner corner form by the Bottom Rail [15] and Fixed Panel [02]. (Fig 12)
2. Allow 24 hours for the silicone to fully cure before using the shower. Use Silicone cleaner [20] to smooth and clean up the silicone.

LEFT SIDE INSTALLATION

The previous steps are for right side installation. For left side installation, please follow the instructions below.

1. Install the shower door by following Step 1, Step 2.
2. Reverse the Support Bar [03] in Step 3 and install. Loosen the screws of the Limit Stops [01] and turn them upward. Tighten the screws again to secure the Limit Stops [01].
3. Reverse the Door [05] as in Step 5 and install.
4. Reverse the Fixed Panel [02] as in Step 6 and install.
5. Continue by following Steps 4, 7 - 12.

Care & Maintenance

BASES/TUBS and BACK WALLS:

Wipe them off after each use with a soft cloth. To clean the acrylic surface, use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes, or scrapers, as they can scratch or dull the surface.

GLASS:

Wipe off the glass after each use with either a soft cloth or a squeegee to prevent soap buildup and water spots (hard water can etch the surface of the glass over time if left to dry). To avoid damaging the surface, never use abrasive cleaners or cleaning products that contain scouring agents. Likewise, never use bristle brushes or abrasive sponges that can scratch the surface.

HARDWARE:

To ensure a long-lasting finish, wipe off the metal parts after using with a soft cloth. Do not use abrasive cleaners or cleaning products containing ammonia, bleach, or acid. If accidentally used, rinse the surface as soon as possible to prevent damage to the finish (peeling or corrosion). After cleaning the polished finishes, rinse thoroughly and wipe dry with a soft cloth. Clean stainless steel surfaces at least once a week. When applying stainless steel cleaner or polish to stainless steel hardware, work with (not across) the grain. Never use an abrasive sponge or cloth, steel wool, or wire brush, which may permanently scratch the surfaces.

NOTE: Regularly inspect the glass and all hardware for misalignment, proper attachment, and damage. Contact ANZZI with any questions or concerns.