AC EV CHARGER
Models
EV-B06-US003A / EV-B06-US003B / EV-B06-US007B
Image of VEVOR EV-B06-US003A charger
Image of VEVOR EV-B06-US003B charger
Image of VEVOR EV-B06-US007B charger with display
Contact Us
For product questions or technical support, please contact: CustomerService@vevor.com
This is the original instruction manual. Please read all instructions carefully before operating. VEVOR reserves the right to interpret its user manual. The appearance of the product received may differ from the manual. VEVOR will not provide further notice for technology or software updates.
Safety Precautions
- Before installation, verify the grid is single-phase 230V ±10% (50 Hz). Failure to do so may render the unit unusable.
- The charging device features user network circuit load capacity detection. If the electric grid circuit cannot support the charging power, the device will automatically reduce charging power. This helps prevent tripping caused by grid voltage instability, circuit aging, or other issues, and reduces safety risks. Reduced charging power during use is a normal phenomenon.
- This equipment includes over-voltage, under-voltage, and overload protection. If the grid voltage remains abnormal after the device adjusts charging power, it will automatically shut down and stop charging.
- Circuit breakers must be installed for the total input of the front-end equipment.
- Do not use flammable, explosive, combustible materials, chemicals, combustible gas, or other dangerous goods near the charging pile.
- Keep the charging point dry and clean. If dirt is present, wipe with a clean, dry cloth. Do not touch the point pin.
- For hybrid cars, recharge only after the engine is turned off. Driving the vehicle while charging is prohibited.
- Keep children away from the charging process to prevent harm.
- Exercise caution when charging during rain, thunder, or adverse weather.
- It is strictly prohibited to use a charging cable that is broken, worn, or exposed. Do not use a charging pile that is obviously knocked down or damaged. If such conditions are observed, move away from the charging post immediately and contact staff.
- In case of fire, electric shock, or other abnormal situations during charging, press the stop button immediately to ensure personal safety.
- Do not attempt to remove, maintain, or modify the charging pile. Improper use may cause damage, leakage, or other issues.
Product Introduction
The VEVOR EV-B06-US series portable charger is designed to address common issues in the portable charging industry. It offers convenient installation, use, and debugging, simple operation and maintenance, accurate measurement, and comprehensive protection functions. It boasts good compatibility and meets national charging standards. The EV-B06-US series portable chargers have an IP66 protection level, providing excellent dustproof and waterproof capabilities for safe indoor and outdoor operation.
Product Parameters
| Type no. | EV-B06-US003A | EV-B06-US003B | EV-B06-US007B |
| Input voltage | AC 120V or AC 240V | AC 240V | AC 240V |
| Output voltage | AC 120V or AC 240V | AC 240V | AC 240V |
| Power output | 3.8KW | 7.7kw | |
| Maximum output current | 16A | 32A | |
| Class of protection | IP66 | ||
| Protection Function | Fire protection, over current, over voltage, under voltage, ground protection, over temperature protection, self monitoring and recovery. | ||
| Indicator light | Standby - Green light steady; Charging - Yellow light blinking; Alarm - Red light on. | ||
| Liquid crystal screen | 3*LED light indicator | 3*LED light indicator | 1.5-inch LCD |
| Mode of charging | Plug and Play/APP charging | ||
| Charging interface | SAE J1772 | ||
| Input plug | NEMA 6-20P | NEMA 10-30P | NEMA 14-50P |
| Material of case | PC+ABS | ||
| Operating temperature | -30~45°C | ||
| Relative humidity | 5% to 95% no condensation | ||
| Overall dimensions | 245*105*63mm(H*W*D) | ||
| Standard of reference | CCS1 (combo/Type 1) AC Level 1 and 2 charging | CCS1 (combo/Type 1) AC Level 2 charging | |
Equipment Instructions
Standby State
After the device is powered on, it enters the standby state. The device standby interface is shown below:
Display shows: 26° C, [Charging Gun Symbol] 16A, 240V, 00.0A, 00.00kWh, 00:00:00
Charging Interface
After inserting the charging gun head into the vehicle charging port, the charging interface is shown below:
Display shows: 26° C, [Charging Gun Symbol] 16A, 240V, 15.6A, 00.01kWh, 00:00:01
Adjust Charging Current
Click the [Button] to adjust the charging current. The charging gear cycles through: 16A-13A-10A-8A-16A. After switching the usage current, plug in the gun head to charge.
Appointment Charging
Click the [Button] to increase the reservation time. You can choose between 0 and 12H. After the appointment time, the device will automatically enter the charging state. All models included in this manual can be charged via APP Appointment charging.
Mobile Phone APP Charging Operation Instructions
APP Download and Binding Use
To download the smart APP, enter the following address in your mobile browser: https://developer.tuya.com/cn/docs/iot/tuya-smart-app-smart-life-app-advantages?id=K989rqa49rluq. Click the website and follow the prompts to install.
QR code download is available, but QR codes are excluded from this document.
Binding and Using Devices
Open the installed APP. Click "Agree privacy Statement" to register using your mobile phone number or social software. Log in to the APP after successful registration.
Long press [Button A] on the charging panel. "APP START" will appear on the display screen to enter the APP mode.
Press and hold the charging panel again. The display screen will show "Plug and Charge" to enter the Plug and Play charging mode. Ensure your mobile phone's Location, Bluetooth, and Wi-Fi are enabled. If the charging device is in standby state, the APP will automatically search for the charging device, and the device name will be displayed.
Adding Device (Manual)
Click "+" in the upper right corner of the APP to manually add the device. Select the category "Energy saving" from the left column, find the device type "Car charging pile (Bluetooth + WIFI)", click to enter, and then click "Confirm indicator flashing" or "Fast flashing" as prompted. Enter the Wi-Fi password (the password for the Wi-Fi connected to your mobile phone) and click "Next" to match the password. Always set the bound device as prompted. After binding, charge the device according to the APP interface.
Device WIFI Reset
| Model | Reset Procedure | Return to Status Interface |
| EV-B06-US 003A and EV-B06-US 003B | Press both [Button A] and [Button R] on the lower panel simultaneously for 3 seconds. After the display screen shows "WIFI Reset", the device's WiFi will be reset. | Under the WiFi reset interface, simultaneously press [Button A] and [Button R] on the device panel for 2 seconds to return to the device status interface. |
| EV-B06-EU 007B | Press both [Button A] and [Button H] on the lower panel simultaneously for 3 seconds. After the display screen shows "WIFI Reset", the device's WiFi will be reset. | Under the WiFi reset interface, simultaneously press [Button A] and [Button H] on the device panel for 2 seconds to return to the device status interface. |
Note: The APP allows setting charging current, reservation time, and other functions. You can also query real-time charging status. The APP controls the charging function, independent of the device's charging mode.
Charging Fault Description
Charging Indicator LED Indicator Status Table
| Device Status | Three-color indicator status (green light: standby, yellow light: charging, red light: failure) |
| Standby mode | Green light steady on |
| The gun has been fired | Steady yellow light |
| The gun is charging | Yellow light flashing |
| Switch current gear status: | |
| EV-B06-US003A | Press the current button and the yellow light will flash once (8A). |
| EV-B06-US003B | Press the current button and the yellow light will flash twice (10A). |
| EV-B06-US007B | Press the current button and the yellow light will flash 3 times (13A). Press the current button and the yellow light will flash 4 times (16A). |
| CP fault | The red light is on. |
| Overpressure and underpressure | The red light flashes once per second. |
| The PE cable is not connected | The red light flashes once in two seconds. |
| Over-Current | The red light flashes every four seconds. |
| Electrical leakage of equipment | The green and red lights flash once every second. |
| Equipment overtemperature | The green and red lights flash every two seconds. |
Fault Display Description (EV-B06-US007B)
Ground Fault
Image displays "Ground Fault". The ground wire is not connected or the ground wire connection is poor.
CP Fault
Image displays "CP Fault". The device detects that the CP voltage exceeds 6V ± 0.8 or 9V ± 0.8. It reports a CP fault, recovers the voltage to within range, and resolves the fault.
Overcurrent Fault
Image displays "Overcurrent Fault". If the charging current exceeds the threshold and continues for 5 seconds, the device will disconnect charging and report a fault that cannot be automatically restored.
Undervoltage Fault
Image displays "Undervoltage Fault". The rated input voltage is 240V. A fault is reported if the voltage value is lower than 192V±5V.
Overvoltage Fault
Image displays "Overvoltage Fault". The rated input voltage is 240V. A fault is reported if the voltage value is higher than 288V±5V.
Installation Instructions
List of Parts
| Category | Item | Quantity | |
| General purpose accessories | Product specification | 1 copy | |
| Storage bag | 1 PCS | ||
| Adapter plug cable (equipped with EV-B06-US003A) | 1PCS | ||
| Wall mount installation | Wall mount | 1 PCS | |
| Wall mounted fasteners | |||
| Expansion screw | M8*60 expansion screw | 4 PCS | |
| Charging cable hook | Iron hook | 1 PCS |
Installation Method: Wall Hanging
- Take out the provided wall mounting fasteners and carefully check the installation dimensions of the screw holes.
- Select the installation location of the device. The lowest position of the equipment should be a wall mounted fastener 1200 mm above the ground.
- Drill 2 holes with a diameter of 8mm according to the location of the fixed screw holes for the wall mounted fasteners. Tap in the expansion rubber plugs. Fix the mounting plate with nuts to secure the chassis. Dimension unit is mm.
Made In China
Contact Us â Official VEVOR Support
开发者平台文档中心-涂鸦开发者
